Leisure Luxe LX105 Bedienungsanleitung

Leisure Spülbecken Luxe LX105

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Leisure Luxe LX105 (2 Seiten) in der Kategorie Spülbecken. Dieser Bedienungsanleitung war für 32 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/2
1821-02
Luxe Inset Sinks Fitting Instructions
1. It is recommended that the Inset sink is tted to the
worktop before being permanently xed to the cabi-
net.
2. Place the sink upside down on worktop. Position the
sink relative to the worktop as required, ensuring that
the cabinet framework will be clear of all parts of the
sink.
With sharp soft pencil draw round sink as accurately
as possible. See g. 1.
3. Remove the sink and draw another line 10mm inside
the outline of the sink top following the corner radii
with care. This is the cutting line for the aperture.
Fig. 1
Fig. 3
4. Drill as large a hole as possible inside the cutting line.
Using a pad saw, jig saw or similar, cut out the aperture
to the cutting line.
5. Remove paper backing from the foam tape and stick
down to the worktop, lining up the inner edge of the
tape 3 to 4mm from the edge of the cut, see g. 2. A
neat butt joint of the two ends is desirable. The tape
may be stretched slightly to obtain this. The worktop
should be clean and dry before application.
6. Attach the xing clips to the sink rail as shown in
g. 3 ensuring that the twoprongs’ of the clip face
inwards.
Open the hinge on the clip.
7. Turn the sink upside down and lay the worktop over
the sink. Swing the clip into position. (This is the most
eective method although if the worktop has been
xed to the cabinet, the sink can be placed in the
aperture and the xing eected from underneath).
8. With the sink secured in position the excess sealing
tape should be cut o by carefully running a sharp
knife or razor blade round the periphery of the sink
and then lifting the excess tape away.
Fig. 2
NB The adjustment of the clamping bracket for U.K. mar-
ket suits worktops of thicknesses 27mm to 43mm.
Any variations from these thicknesses will either
require packing under the clips or for the worktops
to be rebated.
Recommended tightening sequence for sink xing
clips
1821-02
After Care Stainless Sinks
Day to Day Care
Routine cleaning of your stainless steel sink is easy if
the following simple procedure is followed
After use wipe the bowl and drainer with a soft damp
soapy cloth, rinse with clean water. In hard-water ar-
eas, an application of Jif will avoid any build-up of dull
lm of waterborne deposits.
Although stainless steel is an extremely durable mate-
rial and will withstand a great deal of hard use, it can
be scratched by hard or sharp objects. If the surfaces
are to be kept in a blemish free condition reasonable
care should be taken when handling such items.
Discolouration and Heavy Staining
Staining of stainless steel in most cases is due to
something being deposited on the steel rather than
an attack on the material itself. The most common
cause of staining is the build up of a thin lm of water
borne deposits on the sink surface, often rst seen as
a rainbow eect. The build up of such a lm can be
avoided by drying the surface of the sink after use as
described above. However, should such a lm ap-
pear, it can be readily removed with a soft damp cloth
and Jif. To remove the lm, apply the Jif neat and rub
vigorously with a damp cloth along the length of the
sink surface. After cleaning rinse thoroughly with
clean water and dry. Wire wool products and ferrous
water supply pipes can leave minute ferrous particles
adhered to the sink surface. Since stainless steel un-
der normal conditions does not rust, these particles
can cause the appearance of small brown rust stains.
These stains can be removed using the procedure
described above.
CAUTION :
Certain household products contain substances
which will attack the stainless steel surface, they are :
1. Bleaches :
Most common domestic bleaches contain Chlorine in
the form of a hypochlorite. Chlorine attacks the micro-
scopic Chromium Oxide lm on the surface and can
cause pitting of the surface. Bleaches should always
be used in the prescribed strength specied by the
manufacturers. Undiluted bleaches can cause pitting
and staining of the surface and should be immedi-
ately rinsed o with plenty of clean water. All cleaning
agents containing hypochlorites are unsuitable for
use with stainless steel and, even highly diluted, can
cause pitting under certain conditions. For this reason
it is strongly recommended that the sink is not used
for soaking clothes or cleaning clothes in hypochlo-
rite solutions for long periods.
2. Silver Dip Cleaners :
These are particularly harmful since they contain
strong acids which can cause discolouration and pit-
ting. The rst sign of this is an iridescent rainbow stain
which turns an etched dull grey colour. Should any
Silver Dip Cleaner come into contact with the surface
of the sink it should be immediately rinsed o with
plenty of clean water.
3. Corrosive Foodstus :
Fruit juices, damp salt, vinegar, readymade mustards,
pickle and mayonnaise can cause pitting and corro-
sion if left in contact with the stainless steel surface
for long periods.
4. Acids :
Sulphuric, Hydrochloric and other strong acids will
cause pitting corrosion, as will photographic develop-
ing liquids. All should be immediately washed o with
plenty of clean water if contact occurs.
Cleaning :
Always use a soft cloth. The use of coarse grit scour-
ing powders or soap lled wire wool cleaning pads is
not recommended, since both will mark the surface of
the sink. Wire wool pads can leave tiny fragments of
wire embedded in the surface and these can rust and
leave small brown rust stains. Vigorous rubbing with a
soft cloth, JIF, neat detergent, cleaning cream or liquid
will remove these stains. Always remove wet cleaning
aids (cloths, containers, etc.) from the sink surface af-
ter use in order to avoid the formation of water marks
and rust stains.
Meadow Lane, Long Eaton,
Nottingham, NG10 2GD, England
Tel: +44 (0) 115 946 4000 Fax: +44 (0) 115 973 6602
E-mail: consumers@rangemaster.co.uk
www.leis uresinks.co.uk
13
EN 13310 : 2003
Kitchen sink made of:
Cleanability:
Load resistance:
Durability:
Pass
NPD / N/A
Pass
GB
Stainless Steel


Produktspezifikationen

Marke: Leisure
Kategorie: Spülbecken
Modell: Luxe LX105
Breite: 1000 mm
Tiefe: 508 mm
Produktfarbe: Edelstahl
Erste Schale Größe: 190 mm
Anzahl der Spülbecken: 1 Becken
Waschbeckenmaterial: Edelstahl
Abtropfbrett: Ja
Position des Abtropfbretts: Rechts
Wasch-/Spülbeckentyp: Bündiges Waschbecken
Form des Beckens: Rechteckig
Form erste Schüssel: Rechteckig
Abfluss: Ja
Wasserhahn enthalten: Nein
Anzahl der Abflüsse: 1
Größe des Abflusses: 35 mm

Brauchst du Hilfe?

Wenn Sie Hilfe mit Leisure Luxe LX105 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Spülbecken Leisure

Bedienungsanleitung Spülbecken

Neueste Bedienungsanleitung für -Kategorien-