La Crosse Technology WS-9077U-IT Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für La Crosse Technology WS-9077U-IT (2 Seiten) in der Kategorie Wetterstation. Dieser Bedienungsanleitung war für 13 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/2
Battery
Cover
INSTANT TRANSMISSION is the state- -the-art new of
wireless transmission technology, exclusively designed and
developed by LA CROSSE TECHNOLOGY.
INSTANT TRANSMISSION oers you an immediate update
( !) of all your outdoor data measured from every 4 seconds
the transmitters: follow your climatic variations in real-time!
This product oers:
INTRODUCTION:
The Wireless Forecast Station features radio-controlled time, date, forecast
icons, indoor temperature and outdoor temperature on a stylish display.
WIRELESS FORECAST STATION:
SETUP INSTRUCTIONS STEP BY STEP:
Step 1:
Remove battery cover from the outdoor transmitter.
Slide the battery cover down and lift off the back of
the transmitter
Insert 2 NEW AA batteries (not included) into the
TX29U-IT transmitter. Observe the correct polarity.
Keep the Forecast Station and transmitte within 10 r
feet during setup (15 minutes).
Step 2:
Remove battery cover from Forecast Station: insert a solid object in the
space provided at the upper-central position of the battery cover, then push
down and pull out to remove the battery cover.
Insert 2 NEW AA batteries (not included) into the back of the Forecast
Station. Observe the correct polarity (see marking inside the battery
compartment).Do NOT mix old and new batteries.
The will display, time (12:00) and indoor temperature. Forecast Station
Within 3 minutes the Outdoor temperature should be displayed.
Trouble shooting:
After 3 minutes, the Outdoor temperature does not show up in the if
designated area on the Forecast Station, remove batteries from both units
and start the setup process again.
For optimal reception performance, of the 915MHz signal, the outdoor
transmitter should be placed within 330 feet (100 meters) from the Forecast
Station.
WWVB RADIO CONTROLLED TIME
The NIST radio station, WWVB, is located in Ft. Collins, Colorado and
transmits the exact time signal continuously throughout the United States at
60 kHz. The signal can be received up to 2,000 miles away through the
internal antenna in the Forecast Station. However, due to the nature of the
Earth’s Ionosphere, reception is very limited during daylight hours. The
Forecast Station will search for a signal every night when reception is best.
The tower icon will show solid when the Forecast Station has received the
WWVB signal.
No tower icon displayed. The Forecast Station was unable to receive a
signal at this time.
Reposition the Forecast Station for better signal reception or try again at
bedtime.
Note: In case the Forecast Station is not able to detect the WWVB signal
(disturbances, transmitting distance, etc.); the time can be manually set by
following the . Program Menu
FUNCTION BUTTONS:
PROGRAM MENU:
The forecaste station has four function buttons on the front. The SET button
will move through the program menu. The IN or OUT button will change a
value. Press and release the SET button after each step to be moved to the
next step. Exit the programming mode at any time by pressing the CH
button.
CONTRAST: Hold the SET button for ve seconds. LCD and a number
from 0-7 will ash. To increase or decrease the contrast of the LCD
display, press and release the IN button. Press and release the SET
button to confirm and move to the next item.
TIME ZONE: The Time Zone will ash, showing a number following by
the letter h. Use the IN to change the Time Zone. North American Note:
Time Zones are negative numbers: -4h Atlantic, -5h Eastern,- -6h Central,
7h Mountain, -8h Pacic, -9h Alaskan and -10h Hawaiian. Press and
release the SET button to confirm and move to the next item.
DAYLIGHT SAVING TIME: 0 1 DST will show with either (O) or (On)
flashing. Most states use DST, so this should be set to 1. However if
your location does not use DST, use the IN button to turn it 0. Press and
release the SET button to confirm and move to the next item.
RADIO-CONTROLLED TIME: RCC will show with ON or OFF ashing.
Use the IN button to set the RCC signal. Press and release the SET
button to confirm and move to the next item.
12/24-HOUR TIME MODE: Either 12h or 24h will flash on the display.
Use the IN button to change from 12-hour to 24-hour time. Press and
release the SET button to confirm and move to the next item.
HOUR AND MINUTES: The Hour and Minutes Use the will flash. IN
button to advance the Hour. Use the button to advance the OUT
Minutes. Press and release the SET button to confirm and move to the
next item.
YEAR: The Year will ash. Use the IN button to set the year. Press and
release the SET button to confirm and move to the next item.
MONTH AND DATE: The Month and Day will ash. Use the IN button to
advance the . button to advance the . Press and Month Use the OUT Date
release the SET button to confirm and move to the next item.
SNOOZE TIME: Although numbers will flash, this feature is not used as
there is no alarm on this unit. Press and release the SET button to
conrm and move to the next item.
FAHRENHEIT OR CELSIUS: °C°F or will ash. Use the IN button to
select your preference. Press and release the SET button to conrm and
move to the next item.
FORECAST SENSITIV arrowsITY: Two air pressure tendency will
appear and a number will ash under the forecast icon. Press and
release the IN button to select the desired forecast sensitivity setting. The
lowest number is used near the coastline, the highest number is for the
desert, and middle number is for everywhere else. Press and release the
SET button to conrm and exit.
WEATHER FORECAST ICO NS:
The weather forecasting feature is estimated to be 75% accurate. The
weather forecast is based solely upon the change of air pressure over time.
In areas where the weather is not affected by the change of air pressure, this
feature will be less accurate.
There are 3 possible weather forecast icons that will be displayed :
Sunnyindicates that the weather is expected to improve (not that the
weather will be sunny).
Sun with Cloudsindicates that the weather is expected to be fair (not that
the weather will be sunny with clouds).
Clouds with Rainindicates that the weather is expected to get worse (not
that the weather will be rainy).
The weather icons change when the unit detects a change in air pressure.
The icons change in order, from “sunny” to “partly sunny” to “cloudy” or the
reverse. If the symbols do not change then the weather has not changed, or
the change has been slow and gradual.
Weather Tendency Arrows:
These arrows reect current changes in the air pressure.
Up arrow: indicates air pressure is increasing, weather expected to
improve or remain good.
Down arrow: indicates air pressure is decreasing, weather is
expected to become worse or remain poor.
No arrow: No arrow means the pressure is stable.
VIEW CHANNELS:
The Forecast Station can receive up to 3 outdoor transmitters. Extra TX29U-
IT s may be found online or at your retailer. Additional transmitters transmitter
allow you to monitor remote temperature of up to 3 locations within a 330 Ft
wireless range of the Forecast Station.
Press and release the CH button to view a dierent channel. A
shift from one “boxed” number to the next should be observed
in the OUTDOOR LCD.
Note: When only one transmitter is connected, you cannot see
other channels and the channel indicator will not show.
OUTDOOR TRANSMITTER RECEPTION ICON:
When the signal is successfully received from the outdoor transmitter, the
icon will be solid.
The icon will ash when searching for the outdoor transmitter signal.
If reception is not successful, the icon will not be shown in LCD.
MIN/MAX DATA:
View Indoor MIN/MAX Data: Press and release the IN button to view the
Minimum, Maximum and Current Indoor Temperatures and humidity records.
The Time and Date will ash to show when the Minimum or Maximum
Temperature occurred.
Note: The indoor Humidity is not time and date stamped.
Reset Indoor MIN/MAX Data:
tton to select the individual indoor Max or Min Press and release the IN bu
record you wish to reset.
The record is now reset to the Hold the SET button for five seconds.
current day's reading.
Wireless Forecast Station
Model WS-9077U-IT | Quick Setup Guide
View Outdoor MIN/MAX Data: Press and release the OUT button to view
the Minimum, Maximum, and Current Outdoor Temperature records. The
Time and Date will ash to show when the Minimum or Maximum
Temperature occurred.
Reset Outdoor MIN/MAX Data Press and release the OUT button to select
the individual outdoor Max or Min record you wish to reset.
The record is now reset to the Hold the SET button for five seconds.
current day's reading.
LOW BATTERY:
When this icon appears in the indoor (IN) reading section, replace the
batteries in the Forecast Station.
When this icon appears in the outdoor (OUT) readings section, replace
the batteries in the outdoor transmitter.
POSITIONING THE OUTDOOR TRANSMITTER
To achieve a true temperature reading, avoid mounting where direct sunlight
can reach the remote temperature transmitter Forecast Station. While the or
remote temperature transmitter is weather resistant, avoid submersion in
water or snow. We recommend that you mount the remote temperature
transmitter on an outside North-facing wall. The sending range is 330ft
obstacles such as walls, concrete, and large metal objects can reduce the
range. Place both units in their desired location, and wait approximately 15
minutes before permanently mounting to ensure that there is proper
reception.
Wall Mount:
1) Remove the mounting bracket from the remote temperature
transmitter.
2) Place the mounting bracket over the desired shaded location
(wall or table).
3) gh the Throu screw holes of the bracket, mark the mounting
surface with a pencil.
4) Screw mounting bracket onto the mounting surface. Ensure
that the screws are flush with the bracket.
5) transmitter into the bracket. Insert the remote temperature
Note: Mounting with adhesive tape is not recommended as a permanent
mounting solution. Only use the adhesive tape during set-up process.
POSITION THE WIRELESS FORECAST STATION:
Free Standing: The Station comes with the table stand already Forecast
attached Pull the stand out from the back of the Forecast Station and place .
in an appropriate location.
Wall Hanging
1) Close the table-stand.
2) Fix a screw (not included) into the desired wall, leaving
approximately 3/16 of an inch (5mm) extended from the
wall.
3) Place the Forecast Station onto the screw using the
hanging hole on the backside.
4) Gently pull the Forecast Station down to lock the screw
into place.
CARE AND MAINTENANCE:
Do Not Mix Old and New Batteries
Do Not Mix Alkaline, Standard, Lithium or Rechargeable Batteries
Do not expose the Forecast Station to extreme temperatures, vibration or
shock.
Keep the Forecast Station dry.
Clean the Forecast Station with a soft damp cloth. Do not use solvents or
scouring agents.
The eep it out of reach of children. Forecast Station is not a toy. K
The Forecast Station is not to be used for medical purpose or for public
information, but is determined for home use only.
The specications of this product may change without prior notice.
Improper use or unauthorized opening of housing will void the warranty.
If the unit does not work properly, change the batteries.
SPECIFICATIONS:
Indoor Temperature: 14.1 °F to 139.8 °F
(-10°C to +59.9°C)
Update interval: every 10 seconds
Outdoor Temperature: -39.8°F to + 139.8°F
(-39.9°C to 59.9°C)
Transmission range: Up to 330 feet (open air)
Transmission frequency: 915MHz
Update interval: every 4 seconds
Power Requirements:
Wireless Forecast Station: 2-AA, IEC, LR6 batteries (not included)
TX29U-IT Transmitter: 2- C, LR6 batteries (not included) AA, IE
Dimensions:
Wireless Forecast Station: 5.63" x 3.18" x 1.21"
(143.2 x 80.8 x 30.9mm)
TX29U- Transmit 5.05" x 1.5" x .83" IT ter:
(128.27 x 38.1 x 21.08mm)
WARRANTY INFORMATION:
La Crosse Technology, Ltd provides a 1-year limited warranty on this product
against manufacturing defects in materials and workmanship.
This limited warranty begins on the original date of purchase, is valid only on
products purchased and used in North America and only to the original
purchaser of this product. To receive warranty service, the purchaser must
contact La Crosse Technology, Ltd for problem determination and service
procedures. Warranty service can only be performed by a La Crosse
Technology, Ltd authorized service center. The original dated bill of sale
must be presented upon request as proof of purchase to La Crosse
Technology, Ltd or La Crosse Technology, Ltd’s authorized service center.
La Crosse Technology, Ltd will repair or replace this product, at our option
and at no charge as stipulated herein, with new or reconditioned parts or
products if found to be defective during the limited warranty period specified
above. All replaced parts and products become the property of La Crosse
Technology, Ltd and must be returned to La Crosse Technology, Ltd.
Replacement parts and products assume the remaining original warranty, or
ninety (90) days, whichever is longer. La Crosse Technology, Ltd will pay all
expenses for labor and materials for all repairs covered by this warranty. If
necessary repairs are not covered by this warranty, or if a product is
examined which is not in need or repair, you will be charged for the repairs or
examination. The owner must pay any shipping charges incurred in getting
the La Crosse Technology, Ltd product to a La Crosse Technology, Ltd
authorized service center. La Crosse Technology, Ltd will pay ground return
shipping charges to the owner of the product to a USA address only.
The La Crosse Technology, Ltd warranty covers all defects in material and
workmanship with the following specied exceptions: (1) damage caused by
accident, unreasonable use or neglect (including the lack of reasonable and
necessary maintenance); (2) damage occurring during shipment (claims must
be presented to the carrier); (3) damage to, or deterioration of, any accessory
or decorative surface; (4) damage resulting from failure to follow instructions
contained in the owner’s manual; (5) damage resulting from the performance
of repairs or alterations by someone other than an authorized La Crosse
Technology, Ltd authorized service center; (6) units used for other than home
use (7) applications and uses that this product was not intended or (8) the
products inability to receive a signal due to any source of interference.. This
warranty covers only actual defects within the product itself, and does not
cover the cost of installation or removal from a xed installation, normal set-
up or adjustments, claims based on misrepresentation by the seller or
performance variations resulting from installation-related circumstances.
LA CROSSE TECHNOLOGY, LTD WILL NOT ASSUME LIABILITY FOR
INCIDENTAL, CONSEQUENTIAL, PUNITIVE, OR OTHER SIMILAR DAMAGES
ASSOCIATED WITH THE OPERATION OR MALFUNCTION OF THIS PRODUCT.
THIS PRODUCT IS NOT TO BE USED FOR MEDICAL PURPOSES OR FOR
PUBLIC INFORMATION. THIS PRODUCT IS NOT A TOY. KEEP OUT OF
CHILDREN’S REACH.
This warranty gives you specic legal rights. You may also have other rights
specic to the State. Some States do not allow the exclusion of
consequential or incidental damages therefore the above exclusion of
limitation may not apply to you.
For warranty work, technical support, or information contact:
La Crosse Technology, Ltd
2817 Losey Blvd. S.
La Crosse, WI 54601
Contact Support: 1- -782-1610 608
Product Registration:
www.lacrossetechnology.com/support/register
The complete instruction manual is available at:
http://www.lacrossetechnology.com/9077it
Protected under U.S. Patents:
5,978,738
6,076,044
6,597,990
FCC Disclaimer:
This Device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) the device must accept any interference received,
including interference that may cause undesired operation.
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO
OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS
TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER
AUTHORITY TO OPERATE THE EQUIPMENT
All rights reserved. This handbook must not be reproduced in any form, even
in excerpts, or duplicated or processed using electronic, mechanical or
chemical procedures without written permission of the publisher.
This handbook may contain mistakes and printing errors. The information in
this handbook is regularly checked and corrections made in the next issue.
We accept no liability for technical mistakes or printing errors, or their
consequences.
All trademarks and patents are acknowledged.


Produktspezifikationen

Marke: La Crosse Technology
Kategorie: Wetterstation
Modell: WS-9077U-IT

Brauchst du Hilfe?

Wenn Sie Hilfe mit La Crosse Technology WS-9077U-IT benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Wetterstation La Crosse Technology

Bedienungsanleitung Wetterstation

Neueste Bedienungsanleitung für -Kategorien-