La Crosse Technology WS-7017U-IT Bedienungsanleitung

La Crosse Technology Wetterstation WS-7017U-IT

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für La Crosse Technology WS-7017U-IT (9 Seiten) in der Kategorie Wetterstation. Dieser Bedienungsanleitung war für 44 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/9

WS-7017U-IT

Wireless 915 MHz

Radio-Controlled Weather Station

Instruction Manual

FCC ID: OMOTX29U (transmitter)

RF Exposure mobile:

The internal / external antennas used for this mobile transmitter must

provide a separation distance of at least 20 cm (8 inches) from all

persons and must not be co-located or operating in conjunction with

any other antenna or transmitter.”

Statement according to FCC part 15.19:

This device complies with Part 15 of the FCC Rules. Operation is subject

to the following two conditions: (1) this device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

Statement according to FCC part 15.21:

Modifications not expressly approved by this company could void the

user’s authority to operate the equipment.

Statement according to FCC part 15.105:

NOTE:

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause

harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

INVENTORY OF CONTENTS

1. The Wireless Weather Station/ (Figure 1).

2. One remote temperature sensor with mounting bracket (Figure 2).

3. Three each, 1/2" Philips screws.

4. Instruction manual and warranty card.

ADDITIONAL EQUIPMENT (not included)

1. Two fresh AA 1.5V Alkaline batteries for the Wireless Weather

Station.

2. Two fresh AA 1.5V Alkaline batteries for the remote temperature

sensor.

3. One, Philips screwdriver for mounting.

ABOUT WWVB (Radio Controlled Time)

The NIST (National Institute of Standards and Technology-Time and

Frequency Division) WWVB radio station is located in Ft. Collins,

Colorado, and transmits the exact time and date signal continuously

throughout the United States at 60 kHz. The signal can be received up

TABLE OF CONTENTS

Topic Page

Inventory of Contents/Additional Equipment 3

About WWVB 3

Quick Set-Up Guide 4

Detailed Set-Up Guide 5

Battery installation 5

Program Mode

Program Sequence and Default Settings 7

Function Keys 7

Setting the LCD Contrast 7

Setting the Time Zone 8

Daylight Saving Time Setting 8

Radio-controlled Time Setting 9

12/24-hour Time Setting 9

Setting the Time 10

Setting the Year, Day and Month 11

Setting the Snooze 11

Setting the Temperature Format 11

Setting the Forecast Sensitivity 12

Features

Weather Forecast Icons and Tendency Arrows 13

Indoor Temperature, Humidity, & Comfort

Level Indicator 14

Outdoor Temperatures 14

Minimum & Maximum Records (Indoor,

Outdoor, & Resetting) 14

Additional Remote Control Sending Units

(Set-Up, Viewing, & Operation) 15

Mounting 17

Troubleshooting 19

Maintenance & Care 20

Specifications 20

Warranty Information 20

This product offers:

INSTANT TRANSMISSION

is the

stat e-of -t he-ar t new wireles s

transmission technology, exclusively

designed and developed by LA

C R O S S E T E C H N O L O G Y.

INSTANT TRANSMISSION

offers you can an immediate update

(every 4 seconds!) of all your outdoor data measured from the

transmitters: follow your climatic variations in real-time!

GB P.2 GB

P.3

Figure 1

Time LCD

Date LCD

Forecast LCD

Indoor LCD

Outdoor LCD

Mounting

Bracket

TX29U-IT remote

temperature

sensor

Figure 2

SI ZE AA LR6

to 2,000 miles away through the internal antenna in the Weather Station.

However, due to the nature of the Earth’s Ionosphere, reception is

very limited during daylight hours. The Weather Station will search for

a signal every night when reception is best. The WWVB radio station

derives its signal from the NIST Atomic clock in Boulder, Colorado. A

team of atomic physicists is continually measuring every second, of

every day, to an accuracy of ten billionths of a second per day. These

physicists have created an international standard, measuring a second

as 9,192,631,770 vibrations of a Cesium-133 atom in a vacuum. For

more information on the atomic clock and WWVB please see the NIST

website at http://www.boulder.nist.gov/timefreq/stations/wwvb.htm.

QUICK SET-UP GUIDE

Hint:

Use good quality Alkaline Batteries and avoid rechargeable

batteries.

1. Have the Wireless Weather Station and remote temperature sensor

3 to 5 feet apart.

2. Batteries should be out of both units for 10 minutes.

3. Place the batteries into the remote temperature sensor first then

into the Wireless Weather Station.

(All remote temperature sensors must be started before the Wireless

Weather Station)

4. DO NOT PRESS ANY BUTTONS FOR 15 MINUTES.

In this time the Wireless Weather Station and remote temperature

sensor will start to talk to each other and the display will show both the

indoor temperature and humidity, and an outdoor temperature. If the

Wireless Weather Station does not display both temperatures after the

15 minutes please retry the set up as stated above. After both indoor

and outdoor temperatures are displayed for 15 minutes you can place

your remote temperature sensor outdoor and set your time.

The remote temperature sensor should be placed in a dry, shaded

area. The temperature sensor has a range of 330 feet. Keep in mind

that the 330 feet is in open air with no obstructions and that radio

waves DO NOT curve around objects. Actual transmission range will

vary depending on what is in the path of the signal. Each obstruction

(roof, walls, floors, ceilings, thick trees, etc.) will effectively cut signal

range in half.

Example:

A Wireless Weather Station with a 330 feet range is mounted

on an interior wall, so that the signal has to pass through one interior

wall, one exterior wall, and across the 10 feet width of the room between

the 2 walls. The first wall will reduce the range to 165 feet, and the

second wall will reduce the range to 87 feet. Factoring in the 10 foot

room, this leaves a maximum of 77 feet of remaining signal range.

This allowance is typically enough for a frame wall with non-metallic

siding; however certain materials can reduce range even further. Metal

siding, stucco, and some types of glass can reduce signal range by as

much as 3/4 or more, compared to the 1/2 reduction typical of most

obstructions. It is possible to receive a signal through these materials,

however maximum range will be much less due to their tendency to

absorb or reflect a much larger portion of the sensor’s signal.

To complete the set up of your Wireless Weather Station after the 15

minutes have passed please follow the steps that follow in the Detailed

Set-Up Guide.

DETAILED SET-UP GUIDE

I. BATTERY INSTALLATION

(When one temperature sensor is being used)

1. First, insert the batteries to the temperature sensor (see “A. Remote

Temperature Sensor” below).

2. Within 30 seconds of powering up the sensor, insert the batteries

to the Weather Station (see “B. Wireless Weather Station” below).

Once the batteries are in place, all segments of the LCD will light

up briefly. Following the indoor temperature and humidity, and the

time as 12:00 will be displayed. If they are not shown in LCD after

60 seconds, remove the batteries and wait for at least 60 seconds

before reinserting them. Once the indoor data is displayed user

may proceed to the next step.

3. After the batteries are inserted, the Weather Station will start

receiving data signal from the sensor. The outdoor temperature

should then be displayed on the Weather Station. If this does not

happen after 2 minutes, the batteries will need to be removed from

both units and reset from step 1 and the signal reception icon is no

longer shown.

A. REMOTE TEMPERATURE SENSOR

1. Remove the mounting bracket. The bracket snaps on and off easily.

GB P.4 GB

P.5

Battery Cover

2. Remove the battery cover, by sliding the cover down.

3. Observing the correct polarity install 2 AA batteries. The batteries

will fit tightly (to avoid start-up problems make sure they do not

spring free).

4. Replace the battery cover by sliding upwards. Be sure battery cover

is on securely.

B. WIRELESS WEATHER STATION

1. Remove the battery cover. To do this, insert a solid object in the

space provided at the lower-central position of the battery cover,

then push up and pull out on the battery cover.

2. Observe the correct polarity, and install 2 AA batteries.

3. Replace the battery cover.

* When the signal is successfully received by the Weather Station,

the icon will be switched on. (If not successful, the icon will not be

shown in LCD) So the user can easily see whether the last reception

was successful (icon on) or not (icon off). On the other hand, the

short blinking of the icon shows that a reception is being done now.

• If the signal reception is not successful on the first frequency

(915MHz) for 45 seconds, the frequency is changed to 920MHz

and the learning is tried another 45 seconds. If still not successful

the reception is tried for 45 seconds on 910MHz. This will also be

done for re-synchronization.

PROGRAM MODE

Programming Note: If 30 seconds is allowed to pass, or the CH button

is pressed during the programming mode, the unit will confirm/set the

last information entered-the display will stop flashing and return to

normal time-date readings. If you don’t leave the program mode during

the programming of sections III through XII, you can advance to step 4

of the next program setting. If you do leave the program setting (or

want to program a specific setting) follow each instructional step to

program that setting.

I. PROGRAMMING SEQUENCE AND DEFAULT SETTINGS

The programming sequence and default (factory) settings are as

follows:

LCD Contrast 5

Time Zone -5 (Eastern)

Daylight Saving Time 1 (on)

Radio-controlled time receptionON

12/24-hour time 12

Time 12:00

Year 2006

Day and Month 1.1.

Snooze (this function not used) 10

Temperature Format ˚F

Forecast Sensitivity 2

Please note that while there is a snooze adjustment in the programming

this is an unused function as there is no alarm on the Wireless Weather

Station.

II. FUNCTION KEYS

The function keys are located on the front of the unit directly below the

LCD.

III. SETTING THE LCD CONTRAST

1. Press and hold the SET button for 5 seconds.

2. “LCD” will show in the time LCD and the number setting will flash.

Note:

There are 8 LCD contrast levels to choose from-”Lcd 0" is the

lightest, and “Lcd 7” is the darkest.

GB P.6 GB

P.7

Battery Cover

Sensor signal

reception icon*

3. Press and release the IN button to select the level you desire.

4. Press and release the SET button to confirm and advance to the

Time Zone setting.

IV. TIME ZONE SETTING

1. Press and hold the SET button for 5 seconds.

2. “LCD” will show in the time LCD and the number setting will flash.

3. Press and release the SET button again.

4. The time zone will flash in the date LCD.

5. Press and release the IN button to select your time zone.

Note:

When a time zone for the U.S. is selected the corresponding

abbreviation will appear above the time (please see the table on the

next page). It is possible to select any time zone from -12 GMT to +12

GMT (for example to see the time in another country)

TIME ZONES

GMT 0

ALT Atlantic -4

EST Eastern -5

CST Central -6

MST Mountain -7

PST Pacific -8

ALA Alaska -9

HAW Hawaii -10

6. Press and release the SET button to confirm and advance to the

Daylight Saving Time setting.

V. DAYLIGHT SAVING TIME (DST) SETTING

1. Press and hold the SET button for 5 seconds.

2. “LCD” will show in the time LCD and the number setting will flash.

3. Press and release the SET button twice.

4. “DST” will appear in the date LCD and either “1” or “0” will flash.

5. Press and release the IN button to select DST on or off.

“DST 0” indicates that the feature is off and the WWVB will not change

times automatically. “DST 1” indicates that the feature is on and the

WWVB will change times automatically.

Note:

Some locations (Arizona and Hawaii) do not follow Daylight

Saving Time, and should select “DST 0.”

6. Press and release the SET button to confirm and advance to the

radio-controlled time on/off setting.

VI. RADIO-CONTROLLED TIME ON/OFF SETTING

1. Press and hold the SET button for 5 seconds.

2. “LCD” will show in the time LCD and the number setting will flash.

3. Press and release the SET button 3 times.

4. “RCC” will appear in the date LCD and “ON” or “OFF” will flash in

the time LCD.

5. Press and release the IN button to select radio-controlled time on

or off.

6. Press and release the SET button to confirm and advance to the

12/24-hour time setting.

VII. 12 OR 24 HOUR TIME SETTING

1. Press and hold the SET button for 5 seconds.

2. “LCD” will show in the time LCD and the number setting will flash.

3. Press and release the SET button 4 times.

4. “12h” or “24h” will flash in the time LCD.

5. Press and release the IN button to select 12 or 24-hour time format.

GB P.8 GB

P.9

Note:

When in the 12-hour format “P.M.” will appear to the left of the

hour in the time LCD between the hours of noon and midnight.

6. Press and release the SET button to confirm and advance to the

time setting.

VIII. TIME SETTING

There are two methods by which the time and date can be set:

A. Automatically via WWVB reception, or

B. Manually.

A. WWVB (Remote Control Time)

This method requires you to do nothing, except wait for the signal to be

received, and to select a time zone. Reception usually takes

approximately 10 minutes during optimal conditions. The best condition

for reception is at night, between midnight and 6:00 am-when there is

less atmospheric interference. To keep your time as accurate as

possible, Wireless Weather Station conducts a WWVB search every

night between these hours, and overrides any manually set time. The

WWVB tower icon (appearing in the TIME LCD) will flash when a signal-

search is in progress and a signal is being received, and will remain

steady when the signal has been received. If the WWVB time has not

been received after 10 minutes of battery installation, you may manually

set the time or leave the time function alone (reception will occur

regardless). After a successful reception, no more reception attempt

would be made until the following day.

B. MANUAL TIME SETTING

Note:

When in the 12-hour format “P.M.” will appear to the left of the

hour in the time LCD between the hours of noon and midnight.

1. Press and hold the SET button for 5 seconds.

2. “LCD” will show in the time LCD and the number setting will flash.

3. Press and release the SET button 5 times.

4. The time will flash in the time LCD.

5. Press and release the IN button to advance the hours.

6. Press and release the OUT button to advance the minutes.

7. Press and release the SET button to confirm and advance to the

year setting.

IX. SETTING THE YEAR, DAY AND MONTH

Note:

Reception of the WWVB signal will also set the date and day.

The reception of the signal will override any programmed date and

day.

1. Press and hold the SET button for 5 seconds.

2. “LCD” will show in the time LCD and the number setting will flash.

3. Press and release the SET button 6 times.

4. The year will flash in the date LCD.

5. Press and release the IN button to advance the year.

6. Press and release the SET button to confirm and advance to the

day/month setting.

7. The day and month will flash in the date LCD.

8. Press and release the IN button to advance the month.

9. Press and release the OUT button to advance the day.

10.Press and release the SET button to confirm and advance to the

snooze setting.

X. SETTING THE SNOOZE

Note:

This is an unused function of the Wireless Weather Station and

should be disregarded. The setting has no bearing on the operation.

Please press and release the SET button to advance to select the

temperature format.

XI. SELECTING ˚F OR ˚C

1. Press and hold the SET button for 5 seconds.

2. “LCD” will show in the time LCD and the number setting will flash.

3. Press and release the SET button 9 times.

4. Either “˚F” or “˚C” will flash in the time LCD.

5. Press and release the IN button to select the temperature format.

6. Press and release the SET button to confirm and advance to the

forecast sensitivity setting.

GB P.10 GB

P.11

XII. SETTING THE FORECAST SENSITIVITY

Note:

The forecast sensitivity can be adjusted to allow for areas that

have a higher or lower sensitivity to changing air pressure (for example

coastal areas have more pressure change than areas such as southern

Arizona).

The numbers correspond to the amount of air pressure change

necessary to trigger a change in the forecast icon. Areas that tend to

have more air pressure change would set the sensitivity to 3, while

areas that experience lower than normal air pressure change would

set the sensitivity to 1.

1. Press and hold the SET button for 5 seconds.

2. “LCD” will show in the time LCD and the number setting will flash.

3. Press and release the SET button 10 times.

4. Either “1”, “2” or “3” will flash in the time LCD.

5. Press and release the IN button to select the forecast sensitivity

6. Press and release the SET button to confirm the forecast sensitivity

and complete the programming.

FEATURES OF THE WS-7017U-IT

I. WEATHER FORECAST

The weather forecasting feature is estimated to be 75% accurate and

is for the upcoming 12 to 24 hours. The weather forecast is based

solely upon the change of air pressure over time. The WS-7017U-IT

averages past air-pressure readings to provide an accurate forecast-

creating a necessity to disregard all weather forecasting for 12-24 hours

after the unit has been set-up, reset, or moved from one altitude to

another (i.e. from one floor of a building to another floor). In areas

where the weather is not largely affected by the change of air pressure,

the sensitivity setting should be set to 1.

A. WEATHER ICONS

There are 3 possible weather icons that will be displayed in the

FORECAST LCD:

Sunny-indicates that the weather is expected to improve (not that the

weather will be sunny).

Sun with Clouds-indicates that the weather is expected to be fair (not

that the weather will be sunny with clouds).

Clouds with Rain-indicates that the weather is expected to get worse

(not that the weather will be rainy).

These icons indicate the expected weather change in the next 12 to

24 hours. The icon does not give an exact prediction of the weather,

however it should be viewed as a generalization of the expected weather

change (for example a “sunny” icon indicates the weather is expected

to improve).

The weather icons change when the unit detects a change in air

pressure. The icons change in order, from “sunny” to “partly sunny” to

“cloudy” or the reverse. It will not change from “sunny” directly to “rainy”,

although it is possible for the change to occur quickly. If the symbols

do not change then the weather has not changed, or the change has

been slow and gradual.

B. WEATHER TENDENCY ARROWS

Other possible displays in the FORECAST LCD are 2 weather tendency

arrows, one that points up (on the left side of the LCD) and one that

points down (on the right side of the LCD). These arrows reflect current

changes in the air pressure. An arrow pointing up indicates that the

GB P.12 GB

P.13

WWVB Tower Icon

(indicates time reception)

Weather Tendency Arrow

Remote Sensor

Number (Up to 3

Total)

Forecast Icon

Comfort Level

Indicator

Satellite Icon

(indicates outdoor

transmission)

air pressure is increasing and the weather is expected to improve or

remain good, an arrow pointing down indicates that the air pressure is

decreasing and the weather is expected to become worse or remain

poor.

II. INDOOR TEMPERATURE, HUMIDITY, AND COMFORT LEVEL

INDICATOR

The current indoor temperature (viewed on the left) and relative humidity

(viewed on the right) are displayed in the INDOOR LCD. The comfort

level indicator is located at the center of the INDOOR LCD. The indicator

will display a happy face icon when the temperature is between 68˚F

and 79˚F (20˚C and 25.9˚C), and the humidity is between 45% and

65%. A sad face icon will be displayed when the temperature and

humidity are outside the mentioned ranges.

III. OUTDOOR TEMPERATURE

The temperature received from the remote temperature sensor is viewed

in the OUTDOOR LCD. When there is more than one remote

temperature sensor unit in operation, a “boxed” number will appear to

the right of the temperature. This indicates which remote temperature

sensor unit (1, 2, or 3) is currently displaying its data in the OUTDOOR

LCD. (This feature is explained in further detail in section V-Adding

Remote Temperature Sensors).

IV. MINIMUM AND MAXIMUM TEMPERATURE RECORDS

The WS-7017U-IT keeps a record of the MINIMUM and MAXIMUM

temperature, and the time and date of their occurrence-for both the

indoor and outdoor modes.

A. VIEWING THE INDOOR TEMPERATURE AND HUMIDITY

RECORDS

1. Press the IN button once. “MIN” appears above the indoor

temperature and the LCD will flash, indicating that the minimum

temperature and humidity, and the time and date of occurrence of

the indoor temperature are displayed. The minimum records will

display for 30 seconds before returning to the normal display mode.

2. Press the IN button again (once while “MIN” is still displayed, twice

otherwise). “MAX” appears above the indoor temperature and the

LCD will f lash, indicating that the maximum temperature and

humidity, and the time and date of occurrence of the indoor

temperature are displayed.

3. While “MAX” is still displayed press the IN button again to return to

the current data display. Or you can wait 30 seconds, during either

the minimum or the maximum readings, and the unit will

automatically return to current data readings.

B. VIEWING THE OUTDOOR TEMPERATURE RECORDS

1. Press the OUT button once. “MIN” appears above the outdoor

temperature and the LCD will flash, indicating that the minimum

temperature, and the time and date of occurrence are displayed.

The minimum records will display for 30 seconds before returning

to the normal display mode.

2. Press the OUT button again (once while “MIN” is still displayed,

twice otherwise). “MAX” appears above the outdoor temperature

and the LCD will flash, indicating that the maximum temperature

and the time and date of occurrence are displayed.

3. While “MAX” is still displayed press the OUT button again to return

to the current data display. Or you can wait 30 seconds, during

either the minimum or the maximum readings, and the unit will

automatically return to current data readings.

C. RESETTING THE MIMIMUM AND MAXIMUM RECORDS

1. All the indoor records (minimum and maximum) will be reset after

the IN button is pressed and held for 5 seconds.

2. All the outdoor records (minimum and maximum) will be reset after

the OUT button is pressed and held for 5 seconds.

V. ADDING REMOTE TEMPERATURE SENSORS (OPTIONAL)

The WS-7017U-IT is able to receive signals from 2 additional

temperature sensors. The following are instructions for the set-up of

temperature sensor units with the WS-7017U-IT. These extra sensors

can be purchased through the same dealer as this unit.

1. Remove all the batteries from the receiver and sensor(s) and wait

60 seconds. During these 60 seconds, press any button 20 times

to discharge any excess power.

2. Insert the batteries to the first temperature sensor.

3. Within 30 seconds of powering up the f irst sensor, insert the

batteries to the Weather Station. Once the batteries are in place,

all segments of the LCD will light up briefly. Following this the indoor

temperature and indoor humidity, time as 12:00, calendar, and

GB P.14 GB

P.15

weather icons will be displayed. If they are not shown in LCD after

60 seconds, remove the batteries and wait for at least 60 seconds

before reinserting them.

4. The outdoor temperature from the first sensor (channel 1) should

then be displayed on the Weather Station. If this does not happen

and the signal reception icon is not shown, after 2 minutes, the

batteries will need to be removed from both units and reset from

step 1.

5. Insert the batteries to the second sensor as soon as the outdoor

temperature readings from the first sensor are displayed on the

Weather station.

NOTE:

You must insert the batteries into the second sensor within 10

seconds of reception of the first sensor.

6. The outdoor temperature from the second sensor and the “channel

2” icon should then be displayed on the Weather Station. If this

does not happen after 2 minute, the batteries will need to be removed

from all the units and reset from step 1.

7. Insert the batteries to the third sensor as soon as the “channel 2”

icon and outdoor data are displayed on the Weather Station. Then

within 2 minutes, the channel 3 outdoor data from the third sensor

will be displayed and the channel icon will shift back to “1” once the

third sensor is successfully received. If this is not happen, user shall

restart the setting up from step 1.

NOTE:

You must insert the batteries into the third sensor within 10

seconds of reception of the second sensor.

IMPORTANT:

Transmission problems will arise if the setting for multiple

sensors is not followed as described above. Should transmission

problems occur, it is necessary to remove the batteries from all units

and start again the set-up from step 1.

VI. VIEWING AND OPERATING WITH MULTIPLE REMOTE

TEMPERATURE SENSOR UNITS

1. To view the temperature of a different remote temperature sensor

unit, press and release the CH button. A shift from one “boxed”

number to the next should be observed in the OUTDOOR LCD.

2. To view the Minimum/Maximum temperature: first select which

remote temperature sensor to read data from (indicated by the

“boxed” number), then press the OUT button. Pressing this button

once will display the minimum temperature, and the date and time

the data was recorded. Pressing this button a second time (while

“MIN” is still displayed, otherwise press the button twice) will display

the same data for the maximum recordings.

6. To reset the Minimum/Maximum readings, it is necessary to select

which remote temperature sensor you wish to reset. Press and

hold the OUT button for 5 seconds, the records for the selected

remote temperature sensor unit will be reset.

MOUNTING

Note:

Before permanently mounting ensure that the Wireless Weather

Station is able to receive WWVB signals from the desired location.

Also, extreme and sudden changes in temperature will decrease the

accuracy of the Wireless Weather Station, and changes in elevation

will result with inaccurate weather forecasting for the next 12 to 24

hours. These changes will require a 12 to 24 hour wait before obtaining

reliable data. To achieve a true temperature reading, avoid mounting

where direct sunlight can reach the remote temperature sensor or

Wireless Weather Station. While the remote temperature sensor is

weather proof, avoid submersion in water or snow. We recommend

that you mount the remote temperature sensor on an outside North-

facing wall. The sending range is 330ft-obstacles such as walls,

concrete, and large metal objects can reduce the range. Place both

units in their desired location, and wait approximately 15 minutes before

permanently mounting to ensure that there is proper reception. The

Wireless Weather Station should display a temperature in the

OUTDOOR LCD within 4 minutes of setting up.

I. THE REMOTE TEMPERATURE SENSOR

The remote temperature sensor should be mounted with the use of

screws.

A. MOUNTING WITH SCREWS

1. Remove the mounting bracket from the remote temperature sensor.

2. Place the mounting bracket over the desired location.

3. Through the three screw holes of the bracket, mark the mounting

surface with a pencil.

4. Screw mounting bracket onto the mounting surface. Ensure that

GB P.16 GB

P.17

the screws are flush with the bracket.

5. Insert the remote temperature sensor into the bracket.

II. THE WIRELESS WEATHER STATION

The Wireless Weather Station can be mounted in two ways:

• with the table stand or,

• on the wall with the use of a wall hanging screw (not included).

A. USING THE TABLE STAND

The Wireless Weather Station comes with the table stand already

mounted. If you wish to use the table-stand all that is required is to

place the Wireless Weather Station in an appropriate location.

B. WALL MOUNTING

1. Remove the table-stand. To do this, pull down on the stand from

the rear and rotate forward.

2. Fix a screw (not included) into the desired wall, leaving approximately

3/16 of an inch (5mm) extended from the wall.

3. Place the Wireless Weather Station onto the screw using the hanging

hole on the backside.

4. Gently pull the Wireless Weather Station down to lock the screw

into place.

TROUBLESHOOTING

NOTE:

For problems not solved, please contact La Crosse Technology.

Problem: No reception of WWVB time signal.

Solution:

1. Wait overnight for signal.

2. Be sure Weather Station is at least 6 feet from any electrical devices,

such as televisions, computers, or other radio-controlled clocks.

3. Remove batteries for five minutes, reinsert and leave the unit alone

overnight without pressing buttons.

4. If there are still problems, contact La Crosse Technology

Problem: Hour is incorrect (minute and date are correct)

Solution:

Be sure correct time zone and daylight saving time settings are selected.

Problem: The LCD is faint

Solution:

1. Set the LCD contrast to a higher number

2. Replace batteries

Problem: No outdoor temperature is displayed.

Solution:

1. Remove all batteries, reinsert into sender first, then display.

2. Place remote sender closer to display.

3. Be sure all batteries are fresh.

4. Place Temperature Sensor and Weather Station in position so the

straight-line signal is not passing through more than two or three

walls.

Problem:

Temperatures do not match if units are placed next to each other.

Solution:

Each temperature sensor is manufactured to be accurate to within 2˚F

plus or minus and under normal conditions, so two sensors could be

as much as 4˚F different. However, the difference can be exaggerated

further because the sensors are designed for different working

environments. The indoor sensor is less responsive to ambient air

currents because of the shielding effect of the display’s case. In addition,

the case can act as a heat sink to absorb and store heat from external

sources (i.e. handling of the case or radiant heat). Also, the much

greater range of the outdoor temperature sensor requires a different

calibration curve than the indoor range. Error is usually greater at the

extreme ends of a range, making it harder to compare different ranges

with different curves. Under non-laboratory conditions, it is difficult to

compensate for the above factors and obtain an accurate comparison.

GB P.18 GB

P.19

MAINTENANCE AND CARE INSTRUCTIONS

• Extreme temperatures, vibration, and shock should be avoided to

prevent damage to the units.

• Clean displays and units with a soft, damp cloth. Do not use solvents

or scouring agents; they may mark the displays and casings.

• Do not submerge in water.

• Immediately remove all low powered batteries to avoid leakage and

damage.

• Opening the casings invalidates the warranty. Do not try to repair

the unit. Contact La Crosse Technology for repairs.

SPECIFICATIONS

Temperature measuring range:

Indoor: 14.1˚F to 139.8˚F with 0.2˚F resolution.

(-9.9˚C to 59.9˚C with 0.1˚C resolution)

“OFL” displayed if outside this range.

Outdoor: -39.8˚F to 139.8˚F with 0.2˚F resolution.

(-39.9˚C to 59.9˚C with 0.1˚C resolution).

“OFL” displayed if outside this range.

Indoor relative humidity measuring range:1% to 99% with 1% resolution.

(Display “- -” if temperature is

OL.F; display “- -” if < 1% and

“99%” if > 99%)

Indoor Temperature checking interval: Every 10 seconds.

Indoor Humidity checking interval: Every 15 seconds.

Outdoor Temperature checking interval

(Remote Temperature Sensor): Every 4 seconds

Outdoor Temperature reception

(Weather Station): Every 4 seconds.

Transmission Range: 330 feet (in open space).

Power Supply:

Weather Station: 2 x AA, IEC LR6, 1.5V.

Remote Temperature Sensor: 2 x AA, IEC LR6, 1.5V.

Battery life cycle: Approximately 24 months.

Recommended battery type: Alkaline.

Dimensions (H x L x W)

Weather Station (without stand): 8.75" x 4" x 1.5"

(222 x 102 x 38 mm)

Remote Temperature Sensor: 5.05" x 1.50" x 0.83"

(128.3 x 38.2 x 21.2 mm)

WARRANTY INFORMATION

La Crosse Technology, Ltd provides a 1-year limited warranty on this

product against manufacturing defects in materials and workmanship.

This limited warranty begins on the original date of purchase, is valid

only on products purchased and used in North America and only to

the original purchaser of this product. To receive warranty service, the

purchaser must contact La Crosse Technology, Ltd for problem

determination and service procedures. Warranty service can only be

performed by a La Crosse Technology, Ltd authorized service center.

The original dated bill of sale must be presented upon request as proof

of purchase to La Crosse Technology, Ltd or La Crosse Technology,

Ltd’s authorized service center.

La Crosse Technology, Ltd will repair or replace this product, at our

option and at no charge as stipulated herein, with new or reconditioned

parts or products if found to be defective during the limited warranty

period specified above. All replaced parts and products become the

property of La Crosse Technology, Ltd and must be returned to La

Crosse Technology, Ltd. Replacement parts and products assume

the remaining original warranty, or ninety (90) days, whichever is longer.

La Crosse Technology, Ltd will pay all expenses for labor and materials

for all repairs covered by this warranty. If necessary repairs are not

covered by this warranty, or if a product is examined which is not in

need or repair, you will be charged for the repairs or examination. The

owner must pay any shipping charges incurred in getting your La Crosse

Technology, Ltd product to a La Crosse Technology, Ltd authorized

service center. La Crosse Technology, Ltd will pay ground return

shipping charges to the owner of the product to a USA address only.

Your La Crosse Technology, Ltd warranty covers all defects in material

and workmanship with the following specified exceptions: (1) damage

caused by accident, unreasonable use or neglect (including the lack

of reasonable and necessary maintenance); (2) damage occurring

during shipment (claims must be presented to the carrier); (3) damage

to, or deterioration of, any accessory or decorative surface; (4) damage

resulting from failure to follow instructions contained in your owner’s

manual; (5) damage resulting from the performance of repairs or

alterations by someone other than an authorized La Crosse Technology,

Ltd authorized service center; (6) units used for other than home use

(7) applications and uses that this product was not intended or (8) the

products inability to receive a signal due to any source of interference..

This warranty covers only actual defects within the product itself, and

does not cover the cost of installation or removal from a fixed installation,

normal set-up or adjustments, claims based on misrepresentation by

the seller or performance variations resulting from installation-related

circumstances.

LA CROSSE TECHNOLOGY, LTD WILL NOT ASSUME LIABILITY

FOR INCIDENTAL, CONSEQUENTIAL, PUNITIVE, OR OTHER

SIMILAR DAMAGES ASSOCIATED WITH THE OPERATION OR

GB P.20 GB

P.21

MALFUNCTION OF THIS PRODUCT. THIS PRODUCT IS NOT TO

BE US ED FOR MEDICAL PU RPOS E S OR FO R PU BLIC

INFORMATION. THIS PRODUCT IS NOT A TOY. KEEP OUT OF

CHILDREN’S REACH.

This warranty gives you specific legal rights. You may also have other

rights specific to your State. Some States do no allow the exclusion of

consequential or incidental damages therefore the above exclusion of

limitation may not apply to you.

For warranty work, technical support, or information contact:

La Crosse Technology

2809 Losey Blvd. S.

La Crosse, WI 54601

Phone: 608.782.1610

Fax: 608.796.1020

e-mail:

support@lacrossetechnology.com

(warranty work)

sales@lacrossetechnology.com

(information on other products)

web:

www.lacrossetechnology.com

Questions? Instructions? Please visit:

www.lacrossetechnology.com/7017it

form, even in excerpts, or duplicated or processed using electronic,

mechanical or chemical procedures without written permission of the

publisher.

This handbook may contain mistakes and printing errors. The

information in this handbook is regularly checked and corrections made

in the next issue. We accept no liability for technical mistakes or printing

errors, or their consequences.

All trademarks and patents are acknowledged.

TABLE DES MATIÈRES

Sujet Page

Inventaire/ Équipement supplémentaire 24

A propos du WWVB 24

Guide de paramétrage rapide 25

Guide de paramétrage détaillé

Installation des Piles 26

Mode de programmation

Séquence de programmation et réglages par défaut 28

Touches de fonction 28

Contraste de l’écran LCD 28

Fuseau horaire 29

Heure d’été 29

Heure radiocommandée 30

Format 12/24 H 30

Heure 31

Jour date et année 32

Fonction “Snooze” 32

Format d’affichage de la température 32

Sensibilité des prévisions météo 33

Fonctionnalités

Icônes de prévision météo et flèches de tendance 34

Température et humidité intérieures & Indicateur du

confort intérieur 35

Températures extérieures 35

Relevés minimum & maximum

(intérieur, extérieur & remise à zéro) 36

Émetteurs télécommandés supplémentaires

(Installation, Affichage & Fonctionnement) 37

Fixation 38

Dépistage des pannes 40

Entretien & soin 41

Caractéristiques techniques 42

Informations sur la garantie 42

GB P.22 F

P.23

Produktspezifikationen

Marke:	La Crosse Technology
Kategorie:	Wetterstation
Modell:	WS-7017U-IT

Brauchst du Hilfe?

Wenn Sie Hilfe mit La Crosse Technology WS-7017U-IT benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Wetterstation La Crosse Technology

La Crosse Technology V61 Bedienungsanleitung

8 Oktober 2024

La Crosse Technology WS-7091 Bedienungsanleitung

30 September 2024

La Crosse Technology 308-1414B Bedienungsanleitung

29 September 2024

La Crosse Technology C83349 Bedienungsanleitung

23 September 2024

La Crosse Technology V42-PRO Bedienungsanleitung

22 September 2024

La Crosse Technology WS-9005TWC-IT Bedienungsanleitung

13 September 2024

La Crosse Technology V10V2 Bedienungsanleitung

12 September 2024

La Crosse Technology WS-2308 Bedienungsanleitung

12 September 2024

La Crosse Technology WS-9240U-IT Bedienungsanleitung

11 September 2024

La Crosse Technology WS-9047TWC-IT Bedienungsanleitung

11 September 2024

Bedienungsanleitung Wetterstation

Neueste Bedienungsanleitung für -Kategorien-

Hyundai WSP 3080 Bedienungsanleitung

15 Oktober 2024

JUNG WS10R Bedienungsanleitung

5 Oktober 2024

Auriol Z31055B (IAN 77437) Bedienungsanleitung

3 Oktober 2024

Cresta DSX100 Bedienungsanleitung

2 Oktober 2024

Cresta WXR-815 Bedienungsanleitung

29 September 2024

Livoo SL262 Bedienungsanleitung

24 September 2024

Bresser 70-08001 BF-PRO Bedienungsanleitung

24 September 2024

Globaltronics GT-WS-15w Bedienungsanleitung

22 September 2024

Thierry Mugler WS6440575 Bedienungsanleitung

22 September 2024

Ascot AB1-WS-9 Bedienungsanleitung

21 September 2024