La Crosse Technology 308-2408FR Bedienungsanleitung


Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr La Crosse Technology 308-2408FR (6 Seiten) in der Kategorie Wetterstation. Dieser Bedienungsanleitung war fĂĽr 34 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/6
Model: 308-2408FR www.lacrosseclock.com/support Page | 1
Model: 308 2408FR-
Instruction Manual
DC: 103015
LED ALARM CLOCK WITH IN/OUT TEMPERATURE
Note: This product
displays temperature in
Fahrenheit only.
Model: 308-2408FR www.lacrosseclock.com/support Page | 2
WWVB Atomic Time Signal Search
After your clock is powered up, it searches for the Atomic time signal for
seven minutes icon flashes. . The
Note: During Atomic time signal search the buttons will not function, . The
LED will change to low brightness and will return to high brightness after
the Atomic time search . search
• Receiving Atomic signal ( icon flashing)
• Successful Reception ( icon becomes static)
• s Failed Reception ( icon disappear )
H es old / WAVE button until your clock giv a short beep to stop or start
the Atomic time . signal reception
During the search, press button once to show reception mode / WAVE
and signal strength Indication:-
• When a strong signal is detected, display shows with 3 bars
• During reception, the signal strength may move from 1 bar to 2 bars
to 3 bars. This is normal since the clock is detecting Atomic time
signal and other signals in the air at the same time.
Press SET will return to the time display with icon flashing.
For information about WWVB Atomic time visit:
www.nist.gov/pml/div688/grp40/wwvb.cfm
G et Started
Step 1: Insert the AC/DC adaptor to a into the back n outlet hen , t
of the clock.
Step 2 I(Optional): nsert 1 x CR2032 Lithium battery (not
included) to the battery compartment on the back of the
clock . The + side of the battery should face up.
T W004
Sensor
Reset
Stand
Battery
Compartment
2 AAA batteries
LED
Model: 308-2408FR www.lacrosseclock.com/support Page | 3
Step 3: Slide open the battery cover of the wireless TW004
sensor, make sure the channel selector is set at position 1
(top position). Insert 2 x AAA batteries (not included) into
the outdoor sensor. Observe the correct polarity.
Step 4: Peel off the protective label on the front of the clock.
Restart: If the outdoor temperature is not displayed after 3
minutes, remove AC power and & outdoor batteries from the clock
sensor. Press any button on the clock 20 times. After 5 minutes,
return to Step 1 above.
Manual Set Time
1. the button Hold SET to enter time set mode.
2. Press the â–Ľ or â–˛ buttons to adjust the values.
3. the button Press TSE to confirm adjustments and move to the next
item.
Time setting order:
1. Time Zone time zones (- 4 04 Default)
2. DST (Daylight Saving Time On/Off)
3. Hour
4. Minutes
5. Snooze Time (05 -60 minutes)
Press the button SET to exit, or 0 seconds without pressing wait 1
buttons to return to the normal time display.
Set Time Alarm
1. the Hold AL ON.OFF button to enter alarm set mode.
2. values. Press the â–Ľ or â–˛ buttons to adjust the
3. the Press AL ON.OFF button to confirm
adjustments.
Time setting order: 1. Hour 2. Minutes
Press the AL ON.OFF button to exit, or wait 8
seconds without pressing buttons to return to the normal time display.
Note: The alarm will sound for two minutes, then shut off completely.
Activate/Deactivate time Alarm
• Press the AL ON.OFF button once to activate the alarm.
• “ ” The letters AL will appear above the time when the alarm is active.
• Press the AL ON.OFF button once again to deactivate the alarm.
TIME ZONES:
04 Pacific
03 Mountain
02 Central
01 Eastern


Produktspezifikationen

Marke: La Crosse Technology
Kategorie: Wetterstation
Modell: 308-2408FR

Brauchst du Hilfe?

Wenn Sie Hilfe mit La Crosse Technology 308-2408FR benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Wetterstation La Crosse Technology

Bedienungsanleitung Wetterstation

Neueste Bedienungsanleitung fĂĽr -Kategorien-