Korg NTS-2 oscilloscope kit Bedienungsanleitung

Korg DJ Ausrüstung NTS-2 oscilloscope kit

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Korg NTS-2 oscilloscope kit (4 Seiten) in der Kategorie DJ Ausrüstung. Dieser Bedienungsanleitung war für 12 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/4
1
Table of Contents
Introduction .............................................................................2
Main features of this unit .........................................................2
Part names and functions ........................................................2
Making connections and turning on the power ......................2
Turning the power on/o...................................................2
Auto power-o function ....................................................2
Four operating modes .............................................................2
Oscilloscope mode (SCOPE) ..............................................................................................2
Function generator mode (WAVE) ..................................................................................2
Spectrum analyzer mode (FFT) ........................................................................................2
Tuner mode (TUNER) ..........................................................................................................2
Basic operations .......................................................................3
Oscilloscope mode (SCOPE) .....................................................3
Explanations of each parameter ........................................3
Function generator mode (WAVE) ...........................................3
Button 1 (button 3): explanations of each parameter ........3
Button 2 (button 4): explanations of each parameter .......3
CATEGORY = Oscillator .......................................................................................................3
CATEGORY = LFO .................................................................................................................3
CATEGORY = Noise ..............................................................................................................3
CATEGORY = Pulse ..............................................................................................................3
CATEGORY = Envelope .......................................................................................................3
Spectrum analyzer mode (FFT) ................................................3
Explanations of each parameter ........................................3
Tuner mode (TUNER) ................................................................4
Explanations of each parameter ........................................4
Global mode .............................................................................4
1: Input ....................................................................................................................................4
2 : SETTINGS ..........................................................................................................................4
3 : SETTINGS ..........................................................................................................................4
Specications ...........................................................................4
Published 06/2022© 2022 KORG INC. www.korg.com
E 1
NTS-2 oscilloscope kit
MULTIFUNCTIONAL UTILITY KIT
Owner’s Manual
* All product names and company names are the trademarks or registered trademarks
of their respective owners.
2
En Introduction
ank you for purchasing the Multifunctional Utility Kit for the Nu:Tekt NTS-2 Os-
cilloscope Kit. To help you get the most out of your purchase, please read this manual
carefully.
Main features of this unit
is product is an assembly kit that you can use to build a digital oscilloscope. Aside
from letting you view audio output waveforms and CV signals, this oscilloscope func-
tions as a spectrum analyzer, oers a built-in tuner for tuning analog synthesizers, and
lets you output LFO, CV and other signals with its function generator.
Part names and functions
1
5 6 7 8 9
3 4
10
(Bottom)
2
1. Mode button
Use this button to switch between operating modes. Each time you press the button,
the mode changes.
a. Oscilloscope (SCOPE)
b. Function generator (WAVE)
c. Spectrum analyzer (FFT)
d. Tuner (TUNER)
e. Global (GLOBAL)
2. Buttons 1–4
e functions assigned to these buttons dier, depending on the operating mode.
3. START/STOP button
Starts and stops measurement. In function generator mode, this is also used to
output waveforms to an external device.
4. Value knob
Press to select a sub-menu, and turn to edit the selected parameter.
5. INPUT 1, 2 jacks
Connect a stereo (or mono) mini cable here to input the signal you wish to measure.
is lets you monitor the audio output from your musical instrument or input a CV
signal.
6. THRU 1, 2 jacks
Used as a thru out for the signal input from the INPUT 1 and 2 jacks.
7. OUTPUT 1, 2 jacks
Outputs the function generator signal.
Connect these jacks to your device with monaural mini plugs.
8. USB (Type-C) port
Use the included USB cable to connect this unit to the USB port on your computer
or to a commercially available USB standards-compliant AC adapter (at least 5 V
DC 550 mA).
9. Power button
Turns the power on and o. Hold this button down for approximately one second to
turn the power o.
10. Battery compartment
Making connections and turning on the power
USB (type portC)
USB cable
SIGNAL IN
SIGNAL OUT
NTS-2 oscilloscope kit
USB adapter AC
(USB 2.0 compatible)
(commercially available)
Computer
Use the included USB cable to connect this unit to the USB port on your computer
or to a commercially available USB standards-compliant AC adapter (at least 5 V DC
550mA).
Make sure to use the included USB cable.
Use a cable that’s no more than 3 m long when connecting your peripherals to this
unit.
Make sure to use an AC adapter that’s compliant with USB 2.0 standards. Note that
some standards-compliant USB AC adapters might not operate correctly.
Turning the power on/o
Long-press the power button to turn on the unit.
Long-press the power button again to turn the unit o.
Auto power-ofunction
e Nu:Tekt NTS-2 features an auto power-o function that automatically turns the
unit o aer one hour has elapsed without the knob, switches, buttons or other controls
being operated. e auto power-o function is enabled by factory default.
Auto power-o can be disabled using the steps below.
1. Use the mode button to enter global mode.
2. Press button 4 (SETTINGS: Power) a number of times to select “Auto Power
O(USB)” or “Auto Power O(Battery)”.
3. Turn the value knob to change the value to “innite”.
Four operating modes
Oscilloscope mode (SCOPE)
You can view the waveforms from up to four input sources. e functions below are
assigned to buttons 1–4.
1: DISPLAY: Switches between input signals.
2: VERTICAL: Sets the display range for the vertical screen direction (voltage).
3: HORIZONTAL: Sets the display range for the horizontal screen direction (time).
4: TRIGGER: Sets which change in input signal causes the display to update.
Function generator mode (WAVE)
In this mode, signal is output from the OUTPUT 1 and 2 jacks. ese outputs can be
used even while an input signal is being received. You can use the START/STOP button
to turn the waveform output on/o, continuously output the waveform by holding
down the button, or output only one cycle of the waveform (one-shot) by just pressing
the button. e functions below are assigned to buttons 1–4.
1: CATEGORY: Selects the waveform for OUTPUT 2, sets the level and so forth.
2: EDIT: Congures the detailed settings for the OUTPUT 2 waveform.
3: CATEGORY: Selects the waveform for OUTPUT 1, sets the level and so forth.
4: EDIT: Congures the detailed settings for the OUTPUT 1 waveform.
Spectrum analyzer mode (FFT)
is mode lets you observe the frequency characteristics of the input signal, by using a
spectrum analyzer that employs an FFT (fast Fourier transform) algorithm. e func-
tions below are assigned to buttons 1–4.
1: INPUT: Switches between input signals.
2: VERTICAL: Sets the display range for the vertical screen direction (voltage).
3: HORIZONTAL: Sets the display range for the horizontal screen direction (time).
4: TRIGGER: Sets which change in input signal causes the display to update. Nor-
mally, this is set to AUTO.
Tuner mode (TUNER)
is mode measures the pitch of the input signal from the oscillator of an analog syn-
thesizer or other source. You can select between a horizontal meter and a needle-type
(VU) meter view. e functions below are assigned to buttons 1–4.
1: DISPLAY: Selects the tuner display mode.
2: INPUT: Switches between input signals to measure.
3: CALIB: Adjusts the pitch lower or higher than the reference pitch of A=440Hz.
You can adjust the pitch within a range of 410–480 Hz.
4: SCOPE: Switches the oscilloscope display on/o.
3
Basic operations
1. Each time you press buttons 1–4, the parameter assigned to the button in question
changes one at a time and is shown in the popup screen in the display.
2. Once the desired parameter is shown, turn the value knob to edit the value.
3. Measurement starts/stops with each press of the START/STOP button.
is product is a multi-tool intended for use with musical instruments. Do not use
this product for anything under than its intended purpose, such as for calibrating
measurement devices and so on.
Oscilloscope mode (SCOPE)
Oscilloscope mode lets you monitor the input signals coming from the four input sourc-
es (INPUT 1, 2 L/R).
Use VERTICAL to set the voltage range for the vertical screen direction. For example, a
“5V” setting will display a 5 V voltage for each mark on the vertical axis.
Use HORIZONTAL to set the time scale in the horizontal screen direction.
Use the DISPLAY setting to select the inputs shown on the oscilloscope, display multiple
inputs separately or stacked on top of each other, or to display two inputs as an image
for comparing two dierent signals. To compare two signals with each other, set the
vertical and horizontal directions to the same setting.
Use TRIGGER to set the timing at which the scope measures the signal input.
Explanations of each parameter
Button#/NAME Pop Up Enc. Push Enc. Value
1: DISPLAY Overlay 1 ch mode 1L, 1R, 2L, 2R
2 ch mode 1L-1R, 1L-2L, 1R-2R, 2L-2R
4 ch mode ---
Separate-2 2 ch mode 1L-1R, 1L-2L, 1R-2R, 2L-2R
4 ch mode ---
Separate-4 --- ---
X-Y XY 1L-1R, 1L-2L, 1R-2R, 2L-2R
XY-TY overlay 1L-1R, 1L-2L, 1R-2R, 2L-2R
2: VERTICAL 1L Input mode
(DCnAC)
Vertical range:
10 mV–10 V/div (10 m, 20 m,
50 m, 0.1, 0.2, 0.5, 1, 2, 5, 10)
1R
2L
2R
3: HORIZONTAL Sec/Div --- Horizontal range:
50us–1 s/div (50, 100, 200,
500, 1 m, 2 m, 5 m, 10 m,
20m, 50 m, 100 m, 200 m,
500 m, 1)
Position Set position to zero Change center position
4: TRIGGER Auto Set trigger level to
zero
Set trigger level:
−5.00 V–5.00 V (0.01 V step)
Rise
Fall
Rise single
Fall single
START/STOP --- --- Oscilloscope RUN/STOP
* Buttons 1–4 + value knob (when the popup is shown): edits the popup item.
* Button 4 + value knob: push to edit what is triggered.
* START/STOP button: controls the run/stop and single mode standby.
Function generator mode (WAVE)
Use this mode to output oscillator /noise signals that can be handled as audio, or to out-
put LFO/PULSE/envelope signals that can be handled as CV signals. OUTPUT 1 and 2
are completely independent, and dierent categories can be selected and used for each.
Button 1 (button 3): explanations of each parameter
Button#/NAME Pop Up Enc. Push Enc. Value
1 (3): CATEGORY
CATEGORY ---
Oscillator
LFO
Noise
Pulse
Envelope
VOLUME Vpp n dBu Set Output Level
CYCLE MODE ---
Cont.
1-Shot
Push
INPUT
MONITOR ---
O
Input 1L
Input 1R
Input 2L
Input 2R
Button 2 (button 4): explanations of each parameter
CATEGORY = Oscillator
Button#/NAME Pop Up Enc. Push Enc. Value
2: EDIT
WAVE TYPE --- Sine, Square, Tri, Saw-Rise, Saw-
Fall
PITCH Frequency n Note 0.01–10.00 kHz / C-0 – G9
SHAPE Set shape to 50% 0–100%
PHASE Set phase to 0° −180 – +180°
CATEGORY = LFO
Button#/NAME Pop Up Enc. Push Enc. Value
2: EDIT
WAVE TYPE --- Sine, Square, Tri, Saw-Rise, Saw-
Fall
FREQUENCY Frequency n BPM 0.01–10.00 kHz / 0.5–600.0 BPM
DIRECTION Set direction to ± −, ±, +
PHASE Set phase to 0° −180 – +180°
CATEGORY = Noise
Button#/NAME Pop Up Enc. Push Enc. Value
2: EDIT
WAVE TYPE --- White, Pink
TIME Period n BPM 1 ms–10.0 s / 0.5–600.0 BPM
--- --- ---
DUTY Set duty to 100% 0–100%
CATEGORY = Pulse
Button#/NAME Pop Up Enc. Push Enc. Value
2: EDIT
WAVE TYPE --- Positive, Negative
TIME Period n BPM 1 ms–10.0 s / 0.5–600.0 BPM
--- --- ---
DUTY Set duty to 50% 0–100%
CATEGORY = Envelope
Button#/NAME Pop Up Enc. Push Enc. Value
2: EDIT
WAVE TYPE --- Linear, Exp.
TIME Period n BPM 1 ms–10.0 s / 0.5–600.0 BPM
SHAPE Set shape to 50% 0–100%
DUTY Set duty to 100% 0–100%
Spectrum analyzer mode (FFT)
Spectrum analyzer mode uses an FFT (fast Fourier transform) function that lets you
monitor the reference waveform along with a frequency spectrogram of the input
signal. is is useful for seeing where the eects of a lter or the changes you make to a
waveform appear in the frequency bands.
Explanations of each parameter
Button#/NAME Pop Up Enc. Push Enc. Value
1: INPUT -- Input mode: ACnDC 1L, 1R, 2L, 2R
2: VERTICAL INPUT 1L Input mode: ACnDC VERTICAL RANGE:
10 mV–10 V/div (10 m,
20m, 50 m, 0.1, 0.2, 0.5, 1,
2, 5, 10)
INPUT 1R
INPUT 2L
INPUT 2R
3: HORIZONTAL Sec/Div --- Time range (50 us–1 s/div)
Position Set position to zero Change center position
FFT
Range
--- FFT max Range
(1k–20kHz)
FFT
Position
--- FFT min Range (0–19 kHz)
4: TRIGGER AUTO,
Rise, Fall
Set trigger level to
zero
Set trigger level:
−5.00V–5.00 V (0.01 V step)
START/STOP - - FFT RUN/STOP
* Buttons 1–4 + value knob (when the popup is shown): edits the popup item.
* START/STOP button: controls the run/stop and single mode standby.

Produktspezifikationen

Marke: Korg
Kategorie: DJ Ausrüstung
Modell: NTS-2 oscilloscope kit

Brauchst du Hilfe?

Wenn Sie Hilfe mit Korg NTS-2 oscilloscope kit benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung DJ Ausrüstung Korg

Korg

Korg DT-10 Bedienungsanleitung

8 Oktober 2024
Korg

Korg OT-120 Bedienungsanleitung

27 September 2024
Korg

Korg DTR-2000 Bedienungsanleitung

26 September 2024
Korg

Korg A4501 Bedienungsanleitung

15 September 2024
Korg

Korg Pitchclip 2+ Bedienungsanleitung

4 September 2024
Korg

Korg CA-30 Bedienungsanleitung

3 September 2024
Korg

Korg Pitchblack X Pro Bedienungsanleitung

1 September 2024
Korg

Korg KAOSS Replay Bedienungsanleitung

28 August 2024
Korg

Korg AW-2+ Bedienungsanleitung

27 August 2024
Korg

Korg Kaoss PAD Bedienungsanleitung

24 August 2024

Bedienungsanleitung DJ Ausrüstung

Neueste Bedienungsanleitung für -Kategorien-

Line 6

Line 6 HX Effects Bedienungsanleitung

15 Oktober 2024
Tascam

Tascam XS-3 Bedienungsanleitung

2 Oktober 2024
Audio-Technica

Audio-Technica AT-VM95EN Bedienungsanleitung

29 September 2024
Behringer

Behringer CMD DC-1 Bedienungsanleitung

28 September 2024
Festo

Festo CPX-E-CEC-M1 Bedienungsanleitung

24 September 2024
BeamZ

BeamZ StarFuzer Bedienungsanleitung

24 September 2024
Focusrite

Focusrite Clarett 4Pre USB Bedienungsanleitung

23 September 2024
Cambridge

Cambridge TT50 Bedienungsanleitung

23 September 2024
Native Instruments

Native Instruments Traktor Kontrol S3 Bedienungsanleitung

22 September 2024
Pro-Ject

Pro-Ject VC-E Bedienungsanleitung

21 September 2024