Klavis Flexshaper Bedienungsanleitung


Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr Klavis Flexshaper (13 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war fĂĽr 8 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/13
Flexshaper
Flexshaper
Flexshaper
Flexshaper Flexshaper user manual V1.3 Page of 1 13
F
F
F
FFle
le
le
lelex
x
x
xxs
s
s
ssha
ha
ha
hahap
p
p
ppe
e
e
eer
r
r
rr voltage mapper
CV-controlled voltage mapper and waveshaper
Introduction
The Flexshaper is a highly versatile module when it comes to modify evolving voltages in other
directions and levels. Five settings allow you to fold/expand/clip/compress/invert partially or
completely any or audio signal. The module can act as an envelope-shaping tool, frequency CV
multiplier, waveshaper, clipper, distortion, limiter, curve changer, and more. Five CV inputs offer
limitless control over the placement of the voltage points for dynamic signal sculpting.
Flexshaper
Flexshaper
Flexshaper
FlexshaperFlexshaper
Features at a glance
• Process from DC to full audio range
• Unipolar/bipolar input mode switch
• Nominal & clip level LEDs
• Output signal LED
• Input gain knob for nominal level setting,
allows clean flat clipping when overdriven
• Five manual voltage mapping potentiometers
• Five CV control of the voltage mapping points
• Simultaneously active unipolar and bipolar outputs
• Firmware update via a simple audio file
• Compact and skiff-friendly module
Flexshaper
Flexshaper
Flexshaper
Flexshaper Flexshaper user manual V1.3 Page of 2 13
Installation and security
Purpose
This module is meant for installation in a Eurorack-compliant chassis.
It adheres to Eurorack Doepfer mechanical and electrical specifications.
Do not attempt using this module in other mechanical or electrical contexts.
Installation
Before the installation, disconnect the mains power supply from your modular system. Some
power supplies are not safely isolated; there is a risk of injury!
See in the specifications if this module requires 5V from the supply rails. If 5V is needed and your
rack is not providing 5V, do not attempt connection!
Check that the current consumption requirements of this module, when added to your installed
set of modules do not exceed the available current from your supply. This is done by adding up
the current draw of all modules (mA) separately for each of 5V, 12V and -12V rails. (1000mA = 1
amp). If any of these 3 sums exceeds the available current of your supply for that voltage, do not
connect the module to your system; you need a stronger power supply.
The provided supply flat cable can only be inserted in the appropriate orientation at the back of
the module, so there is no risk of error on that end. However, you should pay attention to the
orientation of the cable in the socket of the supply PCB inside your chassis. Cheap sockets
without shrouding may allow you to plug in the connector the wrong way!
The red stripe on the cable should match a stripe printed on the supply board. The stripe also
indicates the -12V side. In case there is no stripe, a -12V marking is a safe indication of the
orientation.
Double check that the connectors are fully inserted and correctly oriented before switching on
the power supply. In case of an anomaly, switch off the power supply immediately and check
everything again.
Flexshaper
Flexshaper
Flexshaper
Flexshaper Flexshaper user manual V1.3 Page of 3 13
Firmware update
If needed, the product can be updated by playing an audio file such as “Flexshaper_1.00.wav”.
Not finding any file on Klavis web product’s page means there is no update available.
Procedure
• Connect a mono or stereo cable between your audio playing device headphone output
and the Flexshaper input.
• Prepare to play the audio file
• Set the play level of your playing device at two thirds
• While pressing the Bipolar button, switch on your modular case supply
• The yellow LED will flash
• Start playing the audio file
If everything goes fine
• The yellow LED will go steady es on
• As the update is progressing, the output white LED will go brighter
• When the white and green LEDs are flashing, the firmware is updated successfully
• Press the button to restart the module
If the sound level is too low
• The red, yellow and white LEDs will blink
• Stop audio playback
• Slightly increase the audio playback level
• Press the button
• Start audio playback from the beginning
If there is an error during the playback
• The red and white LEDs will blink
It is possible that the sound setting was too loud to begin with.
Diminish the sound level drastically and restart the procedure.
Playback error can also be due to various parasitic sound causes:
• Touching the cable
• Using sound-generating features of your phone or computer
• Some power saving feature affects the audio playback
• Surrounding noisy modules, bad electrical grounding or modular supply noise


Produktspezifikationen

Marke: Klavis
Kategorie: Nicht kategorisiert
Modell: Flexshaper

Brauchst du Hilfe?

Wenn Sie Hilfe mit Klavis Flexshaper benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Klavis

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung fĂĽr -Kategorien-