JL Audio MMR-10W-Remote Bedienungsanleitung

JL Audio Kabel für PCs und Peripheriegeräte MMR-10W-Remote

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für JL Audio MMR-10W-Remote (2 Seiten) in der Kategorie Kabel für PCs und Peripheriegeräte. Dieser Bedienungsanleitung war für 7 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/2

FCC Compliance Statement

NOTE: This equipment has been tested and found to comply with

the limits of Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed in accordance

with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which

can be determined by turning the equipment o and on, the user is

encouraged to try to correct the interference by one or more of the

following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit dierent from

that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

Any changes or modications not expressly approved by the party

responsible for compliance could void the user’s authority to operate

this equipment.

Safety Considerations

• Install the receiver module in a dry, well-ventilated location that

does not interfere with your factory-installed systems. If a dry

environment is not available, a location that is not exposed to

heavy splashing may be used. Do not install where it will be directly

exposed to the elements.

• Securely mount the receiver module to avoid coming loose in the

event of a collision, sudden jolt or as a result of repeated vibrations

during normal use.

• While the remote transmitter is designed to be water-resistant, it

should never be submerged under water for prolonged periods or

subjected to high-pressure water spray.

• Do not mount the remote cradle or receiver module in an engine

compartment or areas of extreme heat. Areas exposed to a heater or

hot air should also be avoided.

• Check before drilling to make sure that you will not be drilling into

an exterior panel/hull, fuel tank, gas/brake line, wiring harness or

other vital system.

• Protect all wiring from sharp edges and wear by carefully routing

them, tying them down and using grommets and loom where

appropriate. Secure all wiring using cable ties or wire clamps,

as needed.

Installation Applications

This product is designed for operation in 12 volt, negative-ground

electrical systems. Using this product in systems with positive ground

and/or voltages other than 12 volts may result in damage to the

product and will void the warranty. This product is not certied or

approved for use in aircraft.

What is Included

(1) MMR-10W Remote Transmitter

(1) Remote Cradle

(2) Plastic cable ties

(1) Flat head screw

(1) User Manual

Also Included (MMR-10W only)

(1) MMR-10W Receiver Module

(2) Pan head screws

(1) Quick-release lanyard

Product Description

The MMR-10W is a wireless remote controller designed to add

handheld control functionality to MediaMaster® source units.

Utilizing state-of-the-art, 2.4 GHz wireless technology, the MMR-

10W permits control of your MediaMaster® source unit (with LED

signal conrmation), from up to 150 ft. (45 m) away. The MMR-10W

system consists of a hideaway receiver module and water-resistant

(IP67 rated) remote transmitter. The receiver module is designed to

connect directly to your MediaMaster® and is programmable, with

the ability to pair with up to ten MMR-10W remote transmitters.

A versatile mounting cradle is included, along with a lanyard for

convenient, on-the-go functionality.

IP67 Water Resistance Rating

The MMR-10W remote transmitter has been tested to withstand

immersion in water, up to 1 meter (3.28 ft.) deep, for up to 30 minutes.

Note: While designed to be water resistant, the remote should never

be submerged under water for prolonged periods or subjected to

activity that creates pressure on it that exceeds its depth rating.

Receiver Module Placement & Connection

While the MMR-10W receiver module can be mounted in any

orientation, its installation location should be considered to

optimize RF performance. For example, we recommend that you

avoid mounting the receiver module directly to metal surfaces or

to wire harnesses, especially those containing high-current circuits.

Mounting locations in close proximity to other electronics should also

be avoided to minimize wireless interference. Use the two supplied

pan head screws to mount the receiver module.

The receiver module is designed to connect directly to the 5-pin

“Remote” plug of your MediaMaster®. Use caution when mating

the connectors, as they are keyed and must be aligned to t

properly. Note: If a MMR-20 wired remote controller is installed

with your MediaMaster®, you may use a Y-adaptor (MMC-2Y)

(sold separately) to add/connect the MMR-10W receiver module.

If space directly behind your MediaMaster® is limited, you

may use a remote controller cable (MMC-6 or MMC-25) (each

sold separately) to extend the receiver module’s mounting

options. Once connected, make sure that cables are securely

routed using cable ties and wire clamps, keeping connections

away from areas where they could be submerged in water.

MediaMaster® Wireless Remote Controller

MMR-10W / MMR-10W-Remote

Remote Cradle Mounting

For convenience, a plastic cradle is included to mount the MMR-

10W remote transmitter. The base of the cradle is designed so it can

be installed on a at surface or a tubular structure, such as a pipe/

rail or steering wheel. Note: Select a location that does not interfere

with other factory installed devices or safety equipment. Refer to the

following installation examples for more information.

Surface Mount Example

Attach to a at surface using

the included at head screw.

Pipe/Rail Mount Example

Attach to a straight pipe/rail

using the included plastic

cable ties.

2-Year Limited Warranty (U.S.A.)

Visit www.jlaudio.com for warranty details.

For Service Information in the U.S.A. please call JL Audio customer

service: (954) 443-1100 during normal business hours (Eastern Time)

JL Audio, Inc • 10369 N Commerce Parkway, Miramar, FL 33025

International Warranties:

Products purchased outside the United States of America are covered

only by that country’s distributor and not by JL Audio, Inc.

SKU# 011476 02-14-2017

Replacing the Battery

1. Remove the four screws from

the back of the remote.

2. Gently separate the front half

of the remote.

3. Lift and remove the

silicone keypad from

inside the remote.

4. Turn the remote over to

remove the circuit board.

The battery is installed on

the back of the circuit board.

5. Carefully remove the battery

from its holder and replace

with a CR2032 style battery

or equivalent.

6. Reassemble the remote to

ensure a watertight seal.

Receiver Module Programming

Note: The transmitter and receiver included with the MMR-10W

system are already paired.

Up to ten (10) MMR-10W Remote transmitters may be paired to a

single receiver module.

To Pair A New Transmitter (Required for MMR-10W-Remote)

1. Disconnect +12V power from your MediaMaster® by removing the

5-amp fuse from its fuse holder, unplugging its 4-pin power plug,

or switching o its +12V supply circuit.

2. Reconnect +12V power to your MediaMaster®, then immediately

press and hold both and buttons on the transmitter.

3. Continue holding both and buttons for 5 seconds, then

release both buttons.

• If successful, the status LED will emit two quick ashes with any

button press.

• If unsuccessful, the status LED will emit two long ashes with any

button press.

4. Repeat steps 1 to 3 to pair additional transmitters (up to ten total).

Note: This procedure must be completed within 15 seconds after

reconnecting +12V power (step 2).

LED Signal Conrmation

The MMR-10W transmitter is equipped with a red LED mounted

beneath the MUTE button.

The LED will ash once when any button is pressed, and then a second

time when the button is released to verify that the remote’s transmit-

ted signal was successfully received by the receiver module.

• Two short ashes indicate the signal was sent/received successfully.

• Two long ashes indicate the signal was sent, but not successfully

received. Possible failure causes include low battery level, out of

operating range, or the receiver module is not active (MediaMaster®

is turned OFF).

Remote Control Functions

Below is a list of MMR-10W command functions. The functionality

of some controls will vary depending on the current source and/or

last tuner selected. Note: The MediaMaster® source unit only accepts

commands from the MMR-10W when its display is on a Now Playing

Screen or in the SOURCE: Select menu screen:

PWR • Press to turn the source unit ON

• Press and hold for two seconds to turn the source unit OFF

SRC • Press to turn the source unit ON

• Press to cycle through sources (Last tuner/USB/Bluetooth®/AUX)

VOL+• Press to increase volume

VOL–• Press to decrease volume

MUTE

or • Press to mute/unmute audio (AM/FM/WB/SiriusXM®/AUX)

• Press to pause/resume the current selection (USB/Bluetooth®)

• Press to select the next Favorite (AM/FM/WB/SiriusXM®)

• Press to select the next track (USB/Bluetooth®)

• Press and hold to fast-forward (USB)

• Press to select the previous Favorite (AM/FM/WB/SiriusXM®)

• Press to select the previous track (USB/Bluetooth®)

• Press and hold to fast-rewind (USB)

Specications

Operating Frequency 2.4 GHz

Operating Range* Up to 150 ft. (45 m)

Operating Temperature -4 °F to +167 °F (-20 °C to +75 °C)

IP Rating (Transmitter) IP67

IP Rating (Receiver) IP65

Dimensions

(Transmitter)

2.99 in x 2 in x 1.07 in

76 mm x 50.8 mm x 27.2 mm

Dimensions

(Receiver)

4.02 in x 3.01 in x 1.42 in

102.1 mm x 76.5 mm x 36.1 mm

* Maximum operating range will vary based on installation specics and

transmitter battery level.

Steering Wheel Mount Example

Attach to a steering wheel using the

included plastic cable ties.

In case of misplaced transmitters, you may delete all remotes from the

receiver module’s memory. Note: All paired transmitters will stop

working after deletion. Subsequent remote functionality will require

each transmitter to be paired with the receiver.

To Delete All Transmitters

1. Disconnect +12V power from your MediaMaster® by removing the

5-amp fuse from its fuse holder, unplugging its 4-pin power plug,

or switching o its +12V supply circuit.

2. Reconnect +12V power to your MediaMaster®, then immediately

press and hold both VOL VOL+ and – buttons on an

existing (paired) transmitter.

3. Continue holding both VOL VOL+ and – buttons for 5 seconds,

then release both buttons.

• If successful, the status LED will emit two long ashes with any

button press and the transmitter will no longer control your

MediaMaster®.

• If unsuccessful, the status LED will emit two quick ashes with any

button press and the transmitter will still control your Media-

Master®.

Note: This procedure must be completed within 15 seconds

after reconnecting +12V power (step 2).

Produktspezifikationen

Marke:	JL Audio
Kategorie:	Kabel für PCs und Peripheriegeräte
Modell:	MMR-10W-Remote

Brauchst du Hilfe?

Wenn Sie Hilfe mit JL Audio MMR-10W-Remote benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Kabel für PCs und Peripheriegeräte JL Audio

JL Audio MMR-10W-Remote Bedienungsanleitung

3 August 2024

Bedienungsanleitung Kabel für PCs und Peripheriegeräte

Neueste Bedienungsanleitung für -Kategorien-

APC AR7586 Bedienungsanleitung

8 Oktober 2024

Goobay 68874 Bedienungsanleitung

1 Oktober 2024

Goobay 61259 Bedienungsanleitung

1 Oktober 2024

Kogan KAHBCSPLT4A Bedienungsanleitung

1 Oktober 2024

Digitus HD15/HD15 1.8m Bedienungsanleitung

30 September 2024

Netgear AGM731F Bedienungsanleitung

29 September 2024

Laserliner PersonalCable Bedienungsanleitung

24 September 2024

Hama 00200334 Bedienungsanleitung

23 September 2024

StarTech.com USBAUB1MBK Bedienungsanleitung

21 September 2024

StarTech.com USBAUB3MBK Bedienungsanleitung

21 September 2024