Holman EzySpray 5L Bedienungsanleitung

Holman Nicht kategorisiert EzySpray 5L

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Holman EzySpray 5L (4 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 8 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/4
2
D
3a
2a
Do not attempt to unscrew
the PRESSURETANK lid–
doing so will break the
pressurised seal and
void your warranty!
COMPONENTS
A. SPRAY HEAD
B. WAND
C. TRIGGER
D. HOSE
E. EzySpray® PRESSURETANK
F. WAND THREAD
G. LOCKING NUT
H. TANK OUTLET
I. PRESSURE GAUGE
J. SCHRADER VALVE
K. 12mm HOSE CONNECTION
L. PRESSURE RELEASE VALVE
M. GRAB HANDLE
N. PLUNGER
O. TANK OPENING
P. INLET VALVE CONNECTOR
INTRODUCTION
The portable and lightweight
HOLMAN EzySpray® is an essential tool
for your garden maintenance. The patented
pre-pressurised air tank requires no
manual pumping–connect your garden
hose, fill the reservoir, and away you go!
A standard garden spray would require
manual pumping roughly 1,250 times
for 50L of spraying; the EzySpray
®
doesn’t need a single pump.
To fill your EzySpray®, simply connect
a garden hose to the tank. The gauge
indicates how full the tank is, and the spray
wand gives all the control you need.
Adding fertiliser, herbicide or other additives to
your EzySpray® is easy. Unhook the handle, and
pour in concentrate before filling with water.
For more info and support, visit
www.holmanindustries.com.au
I
2
SPRAY HOSE CONNECTION
a. Remove the protective end cap from the ( )TANKOUTLET H
b. Screw one end of the ( ) onto the HOSE D TANKOUTLET H ( )
c. Screw the other end of the onto the threaded HOSE
end of the SPRAYWAND assembly
LFor the easiest assembly, be sure to screw the hose onto
the tank outlet screwing onto the spray wandbefore
1
SPRAY WAND ASSEMBLY
a. Screw the SPRAY HEAD( ) onto the A WAND THREAD ( )F
b. Loosen (do not remove) the ( ) on the ( )LOCKING NUT G TRIGGER C
c. Insert the opposite end of the ( ) through WAND B
the locking nut on the TRIGGER
d. Tighten the locking nut on the TRIGGER
e. This completes the assembly of the SPRAY WAND
A
A
B
F
B
B
C
G
C
2c
D
C
1a
1c
1b
D
J
Need help? Visit www.holmanindustries.com.au/5l-ezyspray/ for more product information or support.holmanindustries.com.au/ for additional helpScan me with your phone for more resources!
Your EzySpray® is not suitable
for drinking under any
circumstance
3
TANK PRESSURE CHECK
Before filling your EzySpray®, be sure to check the pressure gauge
a. Locate the ( ) on the side of the PRESSUREGAUGE I PRESSURE TANK ( )E
b. Check the pressure gauge reads at least 1 BAR
This is required for the pressurised tank to work correctly
c. If pressure is satisfactory, proceed to Steps 4 and 5
d. If the pressure gauge is low, follow the Re‑pressurise
process in Troubleshooting
Before
filling, the
dial should
read roughly
1bar here
When filling,
the dial will
indicate how
much water is
in the tank
KEEP AIR
NEAR
1 BAR!
WATER
MAX
2
3
45L
B
A
R
0
2 4
5
6
3
AIR LOW
1
L
H
M
Made under license from
Pressuresac Pty Ltd,
Kinglake Australia.
PATENTS
Australia: 2007209766
New Zealand: 569888
United Kingdom: GB2449588
Canada: 2,640,600
P
2a
H
2
Using a pow
dditive? Dis
with a cup
water firs
5 Tank Filling
Tank Filling
Min. tap pressure required
to fill tank: 350kPa
a. Before filling your EzySpray®,
push excess air from your garden
hose by turning on the tap
LThis will stop additional air
using the EzySpray® capacity
b. Once water is flowing out,
you can turn off the tap
c. Locate the 12mm snap‑on
HOSE CONNECTION ( )K
d. Attach the INLET VALVE
CONNECTOR ( )P
e. Add a standard 12mm garden
hose (Q) onto this connection
f. Ensure the INLET VALVE ( ) is P
open and turn the garden hose
tap on begin filling
Watch the
pressure gauge
as the reservoir
fills with water
LThe gauge should begin
moving towards MAX level
g. If your water source is high
pressure, it may trigger
the PRESSURE RELEASE
VALVE ( ) when full to L
stop your EzySpray®
from over‑pressurising:
h. If your water source
is low pressure, the
EzySpray® will stop
filling when it reaches
the maximum pressure
i. Once your EzySpray® is
full, turn off your tap and
close the ( )INLET VALVE P
j. Disconnect the INLET
VALVE ( ) and garden hoseP
LHigh or low pressure
circumstances are fine
and shouldn’t damage
your EzySpray®
Watch for excess
water from the
hose when
disconnecting
5c-e
c
4f
Introducing Spray Additives
®Ensure the SPRAY HOSE
( ) is attached when D
removing or replacing
the GRAB HANDLE to
avoid excess additive or
water squirting out of the
PRESSURE TANK outlet
i. After removing the
GRABHANDLE, follow
your additive instructions to
pour the correct amount into
the TANK OPENING ( )O
j. Insert the PLUNGER into the
TANK OPENING, in the position
shown above, push down and
rotate clockwise to hook the
GRABHANDLE back into place
k. Follow TankFilling Step5 in
to fill the tank with water
and mix in the additive
4 Spray Additives
Removing the Grab Handle
a. Push down on the
GRABHANDLE ( )M
b. Twist counter‑clockwise to
unhook the GRAB HANDLE
from the PRESSURE TANK ( )E
c. Pull the GRAB HANDLE out
of the PRESSURE TANK
d. Place the GRABHANDLE
somewhere clean to
avoid dirt touching the
lubricated PLUNGER ( )N
e. Add fertiliser or other
additives to your EzySpray®
before filling with water
f. Optional: To include more
additive, insert the plunger to
push the first shot into the tank
g. Optional: For powder additives,
include a cup of water in
addition to the additive
h. Repeat Steps 4c and d
as necessary to introduce
ore additive
E
I
K
L
4a
L
5g
4b
M
O
O
N
4e
D
D
D
M
N
KPQ
4 5
Question Answer
Why won’t my EzySpray® work?
Why is the pressure gauge
reading below 1 bar?
nYour EzySpray® may need
to be re‑pressurised:
nThis is only necessary if
the pressure is below 1
bar. It should be able to
hold this minimum pressure
for an extended period
a. Locate SCHRADER (bike)
VALVE( ) on the opposite J
side to the ( )GAUGE I
b. Unscrew the lid off the valve
c. Attach a standard bike pump
d. Pump air in until the gauge
reads at least 1 bar
nCheck the PRESSURE
GAUGE( ) to ensure I
water is in the tank
nCheck hose for kinks
and blockages
nCheck wand for blockages
nTry each setting on the
spray head and check
this for blockages
Why is the pressure release
valve triggered and spraying
water during filling?
nThis is perfectly normal
and means the tank
is full of water
nTurn off your tap and
disconnect your garden hose
6 Spraying
Spray Functions
LThe SPRAY HEAD ( ) A
includes 4 individual spray
functions: JET, , CONE
SHOWER and MIST
a. Before spraying, twist the
orange section of the SPRAY
HEAD to select the desired
Trigger Action
b. To begin spraying, simply
point the SPRAY HEAD in the
desired direction and pull the
orange ( ) leverTRIGGER C
7 Flushing and Cleaning
Spray Functions
It is important to completely flush your EzySpray® with
clean water when finished with chemical spraying
a. After you have completed your
spraying job and the tank has
run out, connect to a tap and
refill the tank with clean water
b. Point your spray wand into a
bucket or anywhere you don’t
mind the excess fluid flowing
c. Hold down the trigger and
let the contents flow through
until the tank is empty
d. Once the tank is empty, we
recommend storing your
EzySpray® in a dry, protected
space out of direct sunlight
8 Troubleshooting
A
Question Answer
Why is my EzySpray® hose
difficult to screw onto
the tank and wand?
nThe hose included with your
EzySpray ®
is designed for
the best seal possible, which
may be difficult to screw
on during initial assembly
nFor the easiest assembly,
screw the hose onto the
tank outlet before screwing
onto the spray wand
Why has the pressure
gauge stopped rising while
filling with water?
nThe EzySpray® can still be
used when not entirely full
nIt may be due to a
low‑pressure water source–
try filling the tank elsewhere
with higher water pressure
Why doesn’t my garden hose
fit on my EzySpray®?
nYour hose may be 18mm
nUnscrew the 12mm hose
connection and replace
with an 18mm version
nVisit www.holmanindustries.
com.au/product/18mm‑
brass‑sprinkler‑adaptor
for more info
How do I empty my EzySpray®? nPoint your spray wand
anywhere you don’t mind
the excess fluid flowing
nHold the trigger and let
the contents spray until
the tank is empty
C
A
J
6b
8c
8a
Don’t leave full
for extended
periods of
time!

Produktspezifikationen

Marke: Holman
Kategorie: Nicht kategorisiert
Modell: EzySpray 5L

Brauchst du Hilfe?

Wenn Sie Hilfe mit Holman EzySpray 5L benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Nicht kategorisiert Holman

Holman

Holman BX4 Bedienungsanleitung

23 August 2024
Holman

Holman EzySpray 5L Bedienungsanleitung

20 August 2024
Holman

Holman Aspect Wi-Fi Analyst WS5070W Bedienungsanleitung

19 August 2024
Holman

Holman WX8 Bedienungsanleitung

18 August 2024
Holman

Holman BTX8 Bedienungsanleitung

18 August 2024
Holman

Holman BTX1 Bedienungsanleitung

11 Dezember 2023

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-

DAS Audio

DAS Audio AX-112-5 Bedienungsanleitung

16 Oktober 2024
Ferplast

Ferplast Ergocomfort Freetime Bedienungsanleitung

16 Oktober 2024
AEG

AEG MECK52 Bedienungsanleitung

16 Oktober 2024
Makita

Makita UR012G Bedienungsanleitung

16 Oktober 2024
Stihl

Stihl HT 70 Bedienungsanleitung

16 Oktober 2024
Ernesto

Ernesto H14270 Bedienungsanleitung

16 Oktober 2024
IFM

IFM AC901S Bedienungsanleitung

16 Oktober 2024
Nedis

Nedis RFPOM120FBK Bedienungsanleitung

16 Oktober 2024
AEG

AEG E9KLCS01 Bedienungsanleitung

16 Oktober 2024
ART

ART ProChannel II Bedienungsanleitung

16 Oktober 2024