Halfords High Mount 3 Bedienungsanleitung
Halfords
Fahrradträger
High Mount 3
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Halfords High Mount 3 (8 Seiten) in der Kategorie Fahrradträger. Dieser Bedienungsanleitung war für 5 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/8
Product may differ from images shown
Special Recommendations
Avoid any vehicle bodywork of insufficient
strength, trim and items such as aerofoils or
spoilers.
IMPORTANT! Carrier straps must always be re-
tightened after cycles have been mounted to the
carrier. Straps should be checked routinely for
signs of wear and abrasion, and any worn straps
must be replaced immediately.
After driving for a few miles STOP and check that
all straps are secure and tight. If necessary,
tighten the straps and tidy away any loose ends.
This must be repeated at suitable intervals
depending on the nature of the road.
Do not exceed 45kg maximum load (3 adult
cycles) or 30kg maximum load (2 adult cycles)
when the carrier is used on a booted saloon.
To ensure full compliance with the road traffic
regulations, the use of lighting board/ number
plate is required if your vehicle’s existing
lighting/number plates are obscured by the use of
the carrier.
Drive with care, the handling characteristics of
your vehicle will be affected when carrying cycles,
(e.g. cornering, braking, side winds etc).
Retain these instructions for future reference,
ensure that any other users of the cycle carrier are
familiar with their contents.
The carrier may obstruct the rear window wiper of
your vehicle. DO NOT operate the wiper with the
carrier fitted.
When positioning cycles on the carrier ensure that
they do not project beyond the profile of the
vehicle and that no part of any cycle can touch the
paintwork.
The use of rear mounted cycle carriers may be
restricted in certain countries outside the UK.
Always check with the relevant national tourist
authorities prior to commencing your journey.
Use cloth or foam padding to prevent abrasion
damage occurring between the frames of your
cycles, or from contact between the cycles and
the cycle carrier.
Care must be taken when positioning and loading
the cycle carrier to avoid placing cycle tyres near
the exhaust, and to ensure that a satisfactory
ground clearance is maintained between the
cycles and the road. Extra care should be taken
when negotiating rough road surfaces, humps and
ferry ramps.
All lengths are approximate.
Kit Contents
Panel hook Chassis hook
Dumbbells
160cm
95cm
Main frame
Please follow instructions carefully to ensure the safety of yourself and other road users.
The initial assembly and fitting of the carrier will take approximately 15 minutes.
Before you begin:
• Due to the contruction of boot lids we recommend only two cycles be carried on saloon
cars with this carrier.
• Make sure all parts are included in the package.
• Ensure that the vehicle boot lid/rear bumper are free from dirt and grime.
High Mount 3 Bike Carrier
Fitting Instructions
Made in the UK
Halfords Ltd, Washford
Redditch, B98 0DE
PI386-02
halfords hi 3 bike 1/2/10 15:13 Page 1
!
1
2 3
6
7
Release the bottom 2 adjuster levers and position the
carrier as illustrated.
There are indicator marks on the ratchet adjusters. Using
these as a guide, lift the bottom support tube counting 5
teeth spacing, then lock in position.
The quick release action should be firm for both opening
and closing. The tension may be set by releasing the
handle and turning clockwise.
Note: It is important that indicator marks on the ratchet
adjusters are in the same positions on both sides.
Lower strap assembly
Select 2 x 95cm straps and assemble the chassis hooks
as illustrated.
Warning: Ensure that the straps are fully tightened on
the chassis hooks.
Feed the strap through the lower set of cambuckles.
WARNING: ENSURE THAT THE STRAPS ARE
INSERTED THROUGH THE CAMBUCKLES IN THE
CORRECT DIRECTION.
4 5
Side strap assembly
Select 2 x 95cm straps and assemble panel hooks
as illustrated.
Note: Ensure that the straps are fully tightened on the
panel hooks.
Feed the strap through the middle set of cambuckles.
WARNING: ENSURE THAT THE STRAPS ARE
INSERTED THROUGH THE CAMBUCKLES IN THE
CORRECT DIRECTION.
Top edge fittings Attachment of the upper
straps to the vehicle
Offer the carrier to the vehicle with the lower tube
approximately 50mm above the upper face of the
bumper. Adjust the upper arm to sit against the tailgate of
your vehicle. The carrier upper support arm should not
rest in the middle of any body panel or glass panel; it
should be positioned in the upper or lower third of the
panel. The carrier main frame should be leaning towards
your vehicle (A) maintaining reasonable clearance,
typically approximately 8cm (3 inches) from the car
bodywork. This will reduce as the straps are tightened.
Ensure that the cycle support arms are adjusted to be
above horizontal (B). Once the carrier is set in the correct
position fully tighten all quick release adjusters.
Top edg e fit ti ng s Select 2 x 160cm straps and assemble
dumbbells as illustrated. Open the tailgate, and from
inside your vehicle thread the straps over the top edge
leaving the dumbbells hanging free. Carefully close the
tailgate then gently pull the straps until the dumbbells sit
firmly against the interior trim.
NOTE: Panel hooks, as shown in step 4, should not be
fitted to a glass edge. In the absence of any glass edges
to the vehicle tailgate, always use the dumbbells to the
top and panel hooks to the side. If your vehicle has glass
edges to the side and a metal top edge the dumbbells
must be fitted to the glass edge position. If your vehicle
has both glass edges to the top and to the sides then
dumbbells should be fitted in all positions replacing the
panel hooks. Dumbbells (Also known as Glass Edge
Fittings) are available separately as an accessory.
halfords hi 3 bike 1/2/10 15:13 Page 3
Produktspezifikationen
| Marke: | Halfords |
| Kategorie: | Fahrradträger |
| Modell: | High Mount 3 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Halfords High Mount 3 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Fahrradträger Halfords
30 August 2024
Bedienungsanleitung Fahrradträger
- Fahrradträger Thule
- Fahrradträger Hapro
- Fahrradträger Fiamma
- Fahrradträger Westfalia
- Fahrradträger Scosche
- Fahrradträger Fischer
- Fahrradträger Atera
- Fahrradträger Bosal
- Fahrradträger BusBiker
- Fahrradträger Buzz Rack
- Fahrradträger Cordo
- Fahrradträger EUFAB
- Fahrradträger Menabo
- Fahrradträger MFT
- Fahrradträger Mont Blanc
- Fahrradträger Mottez
- Fahrradträger Peruzzo
- Fahrradträger Pro User
- Fahrradträger Saris
- Fahrradträger Spinder
- Fahrradträger Twinny Load
- Fahrradträger Uebler
- Fahrradträger Volkswagen
- Fahrradträger Volvo
- Fahrradträger XLC
- Fahrradträger AL-KO
- Fahrradträger Cruz
- Fahrradträger Norauto
- Fahrradträger Elite
- Fahrradträger Bikemate
- Fahrradträger EAL
- Fahrradträger FollowMe
- Fahrradträger Master Load
- Fahrradträger Berger & Schröter
- Fahrradträger Hamron
- Fahrradträger Yakima
- Fahrradträger EQ Max
- Fahrradträger Erickson
- Fahrradträger MovaNext
- Fahrradträger LAS
- Fahrradträger Apai Genie
Neueste Bedienungsanleitung für -Kategorien-
15 Oktober 2024
14 Oktober 2024
11 Oktober 2024
10 Oktober 2024
7 Oktober 2024
7 Oktober 2024
5 Oktober 2024
3 Oktober 2024
30 September 2024
25 September 2024