GE Profile JXDFT214 Bedienungsanleitung

GE Nicht kategorisiert Profile JXDFT214

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für GE Profile JXDFT214 (6 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 3 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/6
49-2001155 Rev. 0 08-22 GEA
Drawer Front Accessory JXDF21T for RV Range
Owner's Manual and
Installation Instructions
Installation Instructions
Use Figure 1 to determine the preferred mounting position of the drawer front to the drawer face.
WARNING Position the drawer front in relation to the
drawer face so that the top of the drawer front is at least
1/2" below the bottom of the range door. This positioning is
important to ensure proper airflow for combustion and cooling
to your range. Proper positioning of the drawer front will also
ensure the range door will not interfere with the drawer front as
the range door and drawer open and close (see Figure 2).
Figure 2
Top of drawer front should
be at least 1/2" below
bottom of range door.
NO SCREW ZONE
NO SCREW ZONE
Overall Width = 21-1/2" (544 mm)
7-3/4" (195 mm) 7-3/4" (195 mm) 3"
(77 mm)
3"
(77 mm)
4"
(100 mm)
4"
(100 mm)
2-3/4"
(70 mm)
1"
(25 mm)
1"
(25 mm)
Overall
Height =
11-1/2"
(292 mm)
6-5/16"
(161 mm)
5-3/16"
(131 mm)
Figure 1
Pilot Holes
x6
What you will need for installation:
• Tape Measure
• Drill with drill bits
• 6 Screws
• Screwdriver
249-2001155 Rev. 0
Use one of the following 2 methods for proper installation:
Method 1: Use existing 6 holes
• The drawer front comes with 6 extruded pilot holes for attaching to the drawer face.
• Referencing the screw spacing from Figure 1, mark on the front face of the drawer where the 6 pilot holes will align.
• Use an appropriately sized drill bit to drill clearance holes through the drawer face.
• It is recommended to use 6 screws with a sheet metal thread that are at least #8 size and long enough to go through
the drawer face and secure into the drawer front. Ensure the screws are not too long and do not interfere with the front
panel of the drawer front.
• Screw the drawer front to the drawer face being careful not to over tighten and strip the screws.
Method 2: Create new pilot holes (use this method if you prefer to mount the drawer
front using holes other than the 6 existing holes)
• It is recommended to use 6 attachment screws positioned around the perimeter of the drawer face. The screws should
be positioned vertically and horizontally as far as possible on the drawer face to ensure maximum stiffness of the
drawer front. Be sure to avoid the "no screw zone" locations from Figure 1.
• It is recommended to use 6 self-tapping screws with a sheet metal thread that are at least #8 size and long enough to
go through the drawer face and secure into the drawer front. Ensure the screws are not too long and do not interfere
with the front panel of the drawer front.
• Use an appropriately sized drill bit to drill clearance holes through the front face of the drawer. This step is optional if
using self-tapping screws.
• Screw the drawer front to the drawer face being careful not to over tighten and strip the screws.
Installation
Care and Cleaning
Painted Drawer Panel
Clean the painted drawer panel with soap and water or a
vinegar and water solution. Do not use commercial oven
cleaners, cleaning powders, steel wool or harsh abrasives
on any painted surface.
Stainless Steel Handle
Do not use a steel wool pad; it will scratch the surface. To
clean the stainless steel surface, use warm sudsy water or
a stainless steel cleaner or polish. Always wipe the surface
in the direction of the grain. Follow the cleaner instructions
for cleaning the stainless steel surface. Cleaners with
oxalic acid such as Bar Keepers Friend Soft Cleansers will
remove surface rust, tarnish, and small blemishes. Use
only a liquid cleanser free of grit and rub in the direction of
the brush lines with a damp, soft sponge.
49-2001155 Rev. 0 08-22 GEA
Façade de tiroir en accessoire JXDF21T
pour cuisinière de VR
Manuel d'utilisation et
instructions d'installation
Instructions d’installation
Utilisez la figure 1 pour déterminer la position de montage préférée pour la façade du tiroir par rapport à l a face du tiroir.
AVERTISSEMENT Positionnez la façade du tiroir par
rapport à la face du tiroir de façon que le haut de la façade
du tiroir se trouve à un minimum de 1/2 po sous le bas de la
porte de la cuisinière. Ce positionnement est important pour
assurer une circulation d'air appropriée pour la combustion
et le refroidissement de votre cuisinière. Le positionnement
correct de la façade du tiroir permet également de s'assurer
que la porte de la cuisinière n'interfère pas avec la façade du
tiroir lorsque la porte de la cuisinière et le tiroir s'ouvrent et se
ferment (voir la Figure 2).
Figure 2
Le haut de la façade du
tiroir doit se trouver à un
minimum de 1/2 po sous
le bas de la porte de la
cuisinière.
Matériel nécessaire pour l’installation :
• Ruban à mesurer
• Perceuse avec forets
• 6 vis
• Tournevis
Largeur hors tout = 21 1/2 po (544 mm)
7-3/4 po (195 mm) 7-3/4 po (195 mm) 3 po
(77 mm)
3 po
(77 mm)
4 po
(100 mm)
4 po
(100 mm)
2-3/ po
(70 mm)
1 po
(25 mm)
1 po
(25 mm)
Hauteur
hors tout =
11 1/2 po
(292 mm)
6-5/16 po
(161 mm)
5-3/16 po
(131 mm)
Figure 1
Trous de
guidage x 6
Hauteur hors tout = 11 1/2 po (292 mm)
Hauteur hors tout = 11 1/2 po (292 mm)


Produktspezifikationen

Marke: GE
Kategorie: Nicht kategorisiert
Modell: Profile JXDFT214

Brauchst du Hilfe?

Wenn Sie Hilfe mit GE Profile JXDFT214 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert GE

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-