Extron TLP 350MV Bedienungsanleitung

Extron Fernbedienung TLP 350MV

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Extron TLP 350MV (4 Seiten) in der Kategorie Fernbedienung. Dieser Bedienungsanleitung war für 10 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/4

TLP 350MV • Setup Guide

Overview

The Extron® TLP 350MV is a wall-mounted TouchLink™ Panel that

provides simple and versatile conﬁguration and control for a range

of IP Link® control systems.

Graphic and text objects are displayed on the screen. These objects

have system control functions associated with them and the

Touchpanel allows you to control those functions.

Two BNC connectors allow the screen to be used to preview composite video or S-video.

NOTE: The RJ-45 output on the rear panel of the TLP 350MV must be connected to a network switch, hub, or router that

is connected to an Ethernet LAN or the Internet. An Extron IP Link controller must also be connected to the same

network. Suggested models include IPL T S series (for example, IPL T S4), IPL 250, IPL T CR48, or IPL T SFI244 .

This guide provides basic instructions for experienced installers to mount and perform initial conﬁguration on the

TLP 350MV. Full instructions and reference material can be found in the , which is available on the TLP 350MV User Guide

Extron Web site (www.extron.com).

TLP 350MV Front Panel Features

Figure 1. TLP 350MV Front Panel (left) and Front Panel with Bezel Removed to Show Recessed Buttons (right).

a monitors the level of ambient light and adjusts the screen brightness and button backlighting.Light sensor —

b provides a graphical user interface with a pressable touch screen display.3.5 inch LCD screen —

c provides audible feedback.Speaker —

d detects movement in front of the panel. When no motion has been detected for a user-deﬁned Motion detector —

period of time, the unit goes into sleep mode, which shuts down the screen display and inactivates all the buttons.

When motion is detected, these functions are restored.

e can be conﬁgured to perform user-deﬁned functions, using the Extron Global Eight backlit push-buttons —

Conﬁgurator software.

f intended for volume control but it can be conﬁgured for other functions.Encoder knob —

Two buttons and an LED are recessed behind the bezel. Remove the bezel using the

Extron removal tool inserted into the tabs on the bottom of the panel, as shown in the

ﬁgure at right.

g activates the on screen menus for calibrating and setting the unit.Menu button —

h allows the unit to be reset in any of four different modes. See the Reset button —

"Reset Modes" section on the back page of this setup guide.

i is visible only when the faceplate has been removed. It lights as an Reset LED —

indicator for the reset modes.

ExtronExtron

Remove Bezel

at Tabs

Extron Removal Tool

TLP 350MV • Setup Guide (Continued)

Mounting the TLP 350MV

Decide where to mount the TLP 350MV and whether to use a 3-gang mud ring or a 3-gang UL-certiﬁed junction box. The

mounting instructions are slightly different depending on your choice:

Using a Mud Ring

1. Use the template provided with the mud ring to mark

the wall. For the mud ring provided, the hole must be

5 25/32 inches (14.68 cm) wide x 3 7/8 inches (9.83 cm) high.

2. Cut a hole in the wall. To avoid making the hole too big, cut

inside the lines you marked.

3. Test the ﬁt by inserting the mud ring into the hole in the wall.

If necessary, use a rasp or ﬁle to enlarge the hole.

4. Insert the mud ring into the hole and use a screw driver to

turn and tighten the locking arms until they clamp the mud

ring to the mounting surface. Do not overtighten.

5. Secure the wall adapter (provided) to the junction box, using

the four screws (provided).

6. Use the Extron removal tool provided to separate the bezel

from the TLP 350MV (see ﬁgure on previous page).

7. Extron recommends using the provided Power over Ethernet (PoE) power

supply. Connect a network switch to the "LAN In" port and run a second cable

from the "Pwr LAN Out" port to the Touch Panel mounting site (see the ﬁgure below).

CAUTION: Whether you use a PoE power supply or a 12 VDC power supply (not provided), you must read the

caution in the Power Supply section of the .TLP 350MV User Guide

NOTE: If both a PoE power supply and a 12 VDC power supply are present, the unit will draw power from the PoE

power supply only.

8. Run video cables with to the mounting site. Leave enough slack in the cables to connect them to the TLP 350MV. Pull

the cables through the mud ring. Connect the cables as shown in the diagram below.

9. Plug the cables into the rear panel connectors of the TLP 350MV (refer the ).TLP 350MV User Guide

10. Secure the TLP 350MV to the mud ring using the two screws provided (top center and bottom center).

11. Do not replace the bezel at this time. You will need access to the recessed Menu and Reset buttons to conﬁgure the

unit.

PWR LAN-OUT LAN-IN

To Network SwitchTo TLP 350MV

Power over Ethernet (PoE) Power Supply

C (yellow cable) Video/Y (white cable)

Locking Arms (4)

Screws (2)

Clips (4)

Mud Ring

TLP 350MV

Bezel

LAPT O P

DVD

DOC CAM

AUXIL IARY

DIS PLAY ON

DIS PLAY OF F

MUT E

Using a UL-Certiﬁed Junction Box

1. Locate a wall stud and mark the position where the junction

box will be placed. Use the size speciﬁcations provided by the

manufacturer.

2. Cut a hole in the wall. To avoid making the hole too big, cut

inside the lines you marked in step .1

3. Test the ﬁt by inserting the junction box into the hole in the

wall. If necessary, use a rasp or ﬁle to enlarge the hole.

4. Insert the junction box into the hole in the wall. Secure it to the

stud using two screws or nails, as appropriate. The front edge of

the junction box must be ﬂush with the front surface of the wall.

5. Secure the wall adapter (provided) to the junction box, using the

four screws (provided).

6. Connect a network switch to the "LAN In" port of the PoE

power supply (provided). Run a second cable from the "Pwr LAN

Out" port to the TLP 350MV mounting site (see the ﬁgure on the

previous page).

7. Run video cables to the mounting site. Leave enough slack in the cables

to connect them to the TLP 350MV. Pull the cables through the mud ring.

8. Connect the cables as shown in the diagram at the bottom of the previous page.

9. Secure the TLP 350MV to the wall adapter. Two clips at the top and two at the bottom

audibly click when the panel moves into place. You should also use the two screws provided (top center and bottom

center).

10. Do not replace the bezel at this time. You will need access to recessed the Menu and Reset buttons to conﬁgure the

unit.

Conﬁguring the TLP 350MV (Initial Setup)

Before use, the TLP 350MV must be conﬁgured using the on-screen menus. There are ﬁve different screens (Main, Vol, Time,

IP, and Vid) that can be selected by pressing the appropriate button at the edge of the screen. There is also an Main Exit

button at the bottom left corner of the screen for leaving the menus.

NOTE: Only the screen provides links to the Main Vol Time IP Vid, , , and screens. All other screens have a link to return to

the screen. After calibrating each group of settings, return to the screen to access the next screen.Main Main

Setup Menu

1. Press the recessed Menu button on the front panel to activate the

top-level menu screen. The menu opens at the Main Setup Page.

2. Touch an area of the screen to bring it into focus and use the and Up

Down buttons or the volume control knob to adjust the value. Some

options have a single button and toggle between and when Off On

the button is pressed.

Use the different menu pages to adjust the following options. For more

details, see the user guide.

Main (shown at right) Shows Power over Ethernet status and adjusts —

the Sleep timer, Backlight, Auto Backlight, and LED Backlight functions.

Vol — Adjusts the Master, Click (global button sounds), and Sounds

(playback .wav ﬁles) volume settings.

Time — Sets the correct time and date.

IP — Sets the IP address and the subnet mask, and enables or disables Dynamic Host Conﬁguration Protocol.

Vid — Provides a small video preview window and the controls to calibrate video contrast, color, brightness, and tint.

Main

Vol

Time

IP Exit

Dn Up

OnOn

Sleep: 00000 Sec

Backlight: 075%

Auto

Vid

LED Motion

Backlight

PoE

Active

Wall Stud

Junction Box

Wall Adapter

TLP 350MV

Bezel

LAPT O P

DVD

DO C CAM

AUXI LIARY

DIS PLAY O N

DIS PLAY O FF

MUT E

Scre

ws (2)

Produktspezifikationen

Marke:	Extron
Kategorie:	Fernbedienung
Modell:	TLP 350MV
Bildschirmdiagonale:	3.5 "
RAM-Kapazität:	16 MB
Breite:	163 mm
Tiefe:	44 mm
Gewicht:	400 g
Produktfarbe:	Black, White
Höhe:	114 mm
Eingebautes Display:	Ja
Betriebstemperatur:	0 - 50 °C
Relative Luftfeuchtigkeit in Betrieb:	10 - 90 %
Zertifizierung:	CE, c-UL, UL\nCE, C-tick, FCC Class A, ICES, VCCI
Display-Hintergrundbeleuchtung:	Ja
Display:	TFT
Temperaturbereich bei Lagerung:	-25 - 70 °C
Luftfeuchtigkeit bei Lagerung:	10 - 90 %
Schnittstelle:	Kabelgebunden
Nachhaltigkeitszertifikate:	RoHS
Flash-Speicher:	7 MB
Lagerungstemperaturbereich (T-T):	-13 - 158 °F
Maximale Reichweite:	- m
Temperatur Betriebsumgebung:	32 - 122 °F
Fernbedienung Nutzung:	TV set-top box, DVD/Blu-ray, PC, TV, VCR
Eingangssignal:	Berührungsbildschrim
Display-Auflösung:	320 x 240 Pixel