Extron TLP 1000TV Bedienungsanleitung

Extron Fernbedienung TLP 1000TV

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Extron TLP 1000TV (4 Seiten) in der Kategorie Fernbedienung. Dieser Bedienungsanleitung war für 7 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/4

Product Category

IMPORTANT:

Refer to www.extron.com for

the complete TLP 1000 Series

user guide before connecting

the product to the power source.

TLP 1000MV and TLP 1000TV • Setup Guide

Overview

The Extron TLP 1000MV (wall-mounted) and TLP 1000TV (desk-mounted) TouchLink™ Panels provide simple and versatile

conﬁguration and control for a range of IP Link® control systems. Graphic and text objects are displayed on the screen.

These objects have system control functions associated with them and the touch overlay allows you to activate or regulate

those functions.

These touchpanels communicate through an Ethernet connection to a conﬁgurable IP Link control processor. Video and

audio input is provided by a twisted pair cable connected to an MTP transmitter.

NOTE: The network output must be connected to a network switch, hub, or router that is connected to an Ethernet

LAN or the Internet. An Extron IP Link controller must also be connected to the same network. Suggested

models include IPL T S series (for example, IPL T S4), IPL 250, IPL T CR48, IPL T SFI244, or IPCP 505.

Extron strongly recommends that power is provided by a Power over Ethernet (PoE) power supply.

This guide provides basic instructions for experienced installers to mount and perform initial conﬁguration on the

TLP 1000 series of touchpanels. Full instructions and reference material can be found in the TLP 1000MV and TLP 1000TV

User Guide, which is available on the Extron website (www.extron.com).

Front Panel Features

Extron TLP 1000MV Extron TLP 1000TV

a when no motion has been detected for a user-deﬁned period of time, the unit goes into sleep Motion Sensor —

mode. When motion is detected by the sensor, the screen display is restored and active.

b is located below the LCD screen.Microphone —

c — is unlit during normal operation. The LED blinks red if the connection to the IP Link Connection status LED

controller is lost.

d one on each top corner can be programmed to provide system feedback. They light red or Programmable LEDs —

green and can blink or light solid.

e has a 1024x600 resolution with a touch overlay. Extron software is used to design and conﬁgure a LCD screen —

graphic user interface to display buttons, text, or icons, which have user-deﬁned functions associated with them.

f Two speakers placed under the screen, on either side of the panel, provide audible feedback for the user.Speakers —

g (can only be seen from above the unit) monitors ambient light level and adjusts screen brightness.Light Sensor —

Product Category

810

Extron TLP 1000MV

Use the Extron pry tool to remove the front faceplate of the

TLP 1000MV:

h activates the for calibrating Menu button — on-screen menus

the unit (see page 3).

i allows the unit to be reset in any of four Reset button —

different modes (see “ ” on page 4).

Reset Modes

j provides feedback about the reset status when the Reset LED —

user presses the reset button (see “ ” on page 4).

Reset Modes

TLP 1000MV Reset Buttons and LED

Rear Panel Features

Extron TLP 1000MV Extron TLP 1000TV

h (Menu button), i (Reset button), and j (Reset LED) — see “TLP 1000MV Reset Buttons and LED“ above.

k Three MTP signal adjustments are available for S-video luminance gain (VID/Y), S-video MTP Signal Adjustments —

chrominance gain (C), and sharpness (S). For composite video signals, the gain is controlled by the VID/Y adjustment.

l A twisted pair cable, terminated with an RJ-45 connector, provides video and audio input MTP Input (optional) —

from an Extron MTP transmitter. For the TLP 1000TV, the MTP port is in the top surface of the recessed area, indicated

by the red arrow.

CAUTION: Ensure the MTP cable is connected to the MTP input and the network cable is connected to the

Network input. The voltages carried by the cables is different and connecting the MTP cable to the

Network input will damage the touchpanel unit.

m A twisted pair cable, terminated Network and Power over Ethernet Connector —

with an RJ-45 connector, provides network connection. For the TLP 1000TV, the LAN

port is in the top surface of the recessed area, indicated by the blue arrow.

Extron recommends using the Power over Ethernet (PoE) power supply (provided).

Use straight-through cables to connect the LAN-IN port to a network switch and the

PWR LAN-OUT port to the LAN port of the touchpanel (see the ﬁgure to the right).

Connect the IEC power cord to a convenient 100 VAC to 240 VAC, 50-60 Hz power

source.

An Extron IP Link control interface must also be connected to the same network

domain as the TouchLink Panel. See the note on page 1 for a list of suggested models.

CAUTION: Do not connect any power supply before reading the Cautions about power supplies in the “Panel

Features” section of the .TLP 1000MV and TLP 1000TV User Guide

n Extron recommends using the PoE power supply (provided). As an alternative, Power connector (optional) —

you may choose to connect the two pole, 3.5 mm captive screw connector from the 12 VDC, 1.0 A power supply (not

provided) to the power supply socket on the rear panel.

o For use with the Extron LPVM-1 (part number ). For VESA mounting holes (TLP 1000TV only) — 60-1099-02

complete mounting options of both the TLP 1000MV and TLP 1000TV, see the .TLP 1000MV and TLP 1000TV User Guide

PWR LAN-OUT LAN-IN

To Networ

k Switch

To TLP 1000

Power er Ethernet (PoE) wer Supplyov Po

Product Category

Initial Conguration

Before use, conﬁgure the touchpanel, using the on-screen menus.

1. Press the Menu button once. (See “ “ TLP 1000MV Reset Buttons and LED

for the TLP 1000MV or “ “ for the TLP 1000TV.) The Rear Panel Features

Main menu screen opens (see ﬁgure at right).

2. Touch an on-screen button to highlight and select that option (the button

turns green with a yellow border).

3. Use the and buttons to adjust the value. Some options have a

single button and toggle between and when the button is pressed.

There are ﬁve different screens ( , , , , and ) that

can be selected by pressing the appropriate button at the left side of the screen. There is also an button at the bottom

left corner of the screen for leaving the menus.

Use the screens to adjust the following options (for more information, see the ).TLP 1000MV and TLP 1000TV User Guide

Main — Adjusts the Sleep timer, Backlight, Auto Backlight, and Wake on Motion functions. The screen also provides

information about the PoE status.

Volume — Adjusts the Master, Click, Sounds, and Line In volume settings.

Time — Sets the correct time and date.

Network — Sets the IP address and the subnet mask, and enables or disables Dynamic Host Conﬁguration Protocol.

Video — Provides a small video preview window and the controls to adjust the video contrast, color, brightness, and tint.

Calibration Menu

1. Press the Menu button a second time to open the calibration-screen. (See

“ “ for the TLP 1000MV or “TLP 1000MV Reset Buttons and LED Rear Panel

Features“ for the TLP 1000TV.) The on-screen button in the top left corner

is highlighted.

2. Press the highlighted button until it turns gray and a new button is

highlighted. When all four points have been calibrated, the screen reopens

to the Main Screen.

3. Press to close the on-screen menus.

4. If necessary (for the TLP 1000MV), reattach the faceplate.

Mounting Options

TLP 1000MV

zWall-mounting — using the Extron BB 1000M back box (part number ) or the Extron EWB 1000 wall box 70-887-01

(part number ), either of which must be purchased separately. Follow the instructions provided with the kit. 70-950-02

The unit may also be mounted directly to the wall without a kit, as described on page 4.

zFurniture-mounting — as described on page 4.

zRack-mounting — using the RM 1000M kit (part number ), which must be purchased separately. Follow the 70-886-01

instructions in the user guide provided with the kit.

TLP 1000TV

zDesktop-mounting — by standing the unit on a suitable surface. For added security, the unit may be attached to the

desktop, using two screws, as described in the .TLP 1000MV and TLP 1000TV User Guide

The TLP 1000TV can also be mounted using the Extron SMA-1 Swivel-Mount Adapter (part number ), which 70-747-01

must be purchased separately. Follow the instructions provided with the kit and the TLP 1000MV and TLP 1000TV User

Guide.

zVESA-mounting — using the D-type (75 x 75 mm) mounting pattern. The Extron LPVM-1 kit (part number 60-1099-02)

is optional and must be purchased separately. Follow the instructions provided with the kit. To VESA-mount the TLP

1000TV, the base must be removed from the unit, as described in the .TLP 1000MV and TLP 1000TV User Guide

Main

Volume

Time

Network

Video

Exit

Down Up

Sleep timer: 300 Sec

Down Up

Backlight: 073%

Auto Backlight

Wake on Motion

PoE

Active

Press and Hold

Highlighted Box

Until Color Changes

Produktspezifikationen

Marke:	Extron
Kategorie:	Fernbedienung
Modell:	TLP 1000TV
Bildschirmdiagonale:	10.1 "
Breite:	254 mm
Tiefe:	186 mm
Gewicht:	2400 g
Produktfarbe:	Schwarz
Höhe:	182 mm
Eingebautes Display:	Ja
Betriebstemperatur:	0 - 50 °C
Relative Luftfeuchtigkeit in Betrieb:	10 - 90 %
Paketgewicht:	4000 g
Zertifizierung:	CE, c-UL, UL\nCE, C-tick, FCC Class A, ICES, KCC, VCCI
Display-Hintergrundbeleuchtung:	Ja
Display:	TFT
Temperaturbereich bei Lagerung:	-20 - 60 °C
Luftfeuchtigkeit bei Lagerung:	10 - 90 %
Schnittstelle:	Kabelgebunden
Verpackungsabmessungen (BxTxH):	289 x 311 x 267 mm
Lagerungstemperaturbereich (T-T):	-4 - 140 °F
Maximale Reichweite:	- m
Temperatur Betriebsumgebung:	32 - 122 °F
Fernbedienung Nutzung:	DVD/Blu-ray, PC, TV, VCR
Eingangssignal:	Berührungsbildschrim
Display-Auflösung:	1024 x 600 Pixel