Extech SDL800 Bedienungsanleitung
Lesen Sie kostenlos die đ deutsche Bedienungsanleitung fĂŒr Extech SDL800 (10 Seiten) in der Kategorie Messung. Dieser Bedienungsanleitung war fĂŒr 5 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/10
USER GUIDE
Vibration Meter
SD Card real-time datalogger
Model SDL800
2 SDL800-en-GB_V1.4 6/15
Introduction
Congratulations on your purchase of the Extech SDL800 Vibration Meter. This meter displays and
stores vibration readings of Acceleration, Velocity and Displacement. Supported measurement units
are meters/s2, ft/s2, g, mm/s, cm/s, in/s, mm and inch. Logged data readings are stored on an SD
card for transfer to a PC. This meter is shipped fully tested and calibrated and, with proper use, will
provide years of reliable service.
Safety
International Safety Symbols
This symbol, adjacent to another symbol or terminal, indicates the user must refer to the
manual for further information.
Meter Description
1. Vibration pickup input jack
2. Measurement Display
3. HOLD and Backlight key
4. Power ON-OFF key
5. Up arrow âČ / UNIT key
6. Down arrow ⌠/ Function key
7. ENTER and LOG key
8. SD card slot
9. Vibration pickup
10. DC Adaptor socket, Reset key
and Data output jack
11. SET and Clock key
12. MAX-MIN key
13. Unit of measure Display
Notes: Items listed in â10â are located behind the snap-off compartment cover on meterâs right side.
Battery compartment, tilt stand, and tripod mount are located on the rear of the instrument
3 SDL800-en-GB_V1.4 6/15
Getting Started
Power ON-OFF
ï· Power the meter by pressing and holding the power button for at least 1.5 seconds.
ï· Press and hold the power button for at least 1.5 seconds to power OFF the meter.
ï· This meter is powered by six (6) 1.5VDC âAAâ batteries or by optional AC adaptor. If the meter
will not switch ON please check that fresh batteries are installed in the rear battery compartment
or, in the case of the AC adaptor, check that the adaptor is connected correctly to the meter and
to an AC source.
Display Backlight
To turn the display backlight ON or OFF, press and hold the backlight button for at least 1.5
seconds. The meter will beep when switching the backlight ON or OFF unless the beeper is
disabled.
Vibration Sensor
Connect the vibration pickup to the cable supplied. Make sure it is firmly attached.
Connect the cable to the meter by attaching it to the BNC connector on the top of the meter.
If the surface to be tested is magnetic, attach the magnetic base to the vibration pickup and attach
the pickup to a flat surface.
If the surface to be tested is not magnetic, hold the pickup against the surface. Do not hold the
cable while making measurements.
Units of Measure
The currently selected unit of measure is shown on the meterâs LCD. To change the unit of
measure, press and hold the UNIT button until the desired unit of measure appears and then
release the UNIT button. The meter begins scrolling through the available units of measure after the
UNIT button has been depressed for at least 1.5 seconds. The saved units will become the default
turn-on units.
UNIT DISPLAY INDICATOR
ACC m/s2
g
VEL mm/s
cm/s
DISP p-p mm
ACC ft/s2
VEL In/s
DISP p-p inch
Produktspezifikationen
| Marke: | Extech |
| Kategorie: | Messung |
| Modell: | SDL800 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Extech SDL800 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Messung Extech
19 Juni 2024
19 Juni 2024
5 Juni 2024
29 Mai 2024
22 April 2024
21 April 2024
14 April 2024
7 April 2024
31 MĂ€rz 2024
10 MĂ€rz 2024
Bedienungsanleitung Messung
- Messung Hama
- Messung REV
- Messung Voltcraft
- Messung Bosch
- Messung Laserliner
- Messung Velleman
- Messung Powerfix
- Messung Alecto
- Messung Beurer
- Messung Bresser
- Messung König
- Messung TFA
- Messung Black And Decker
- Messung Trotec
- Messung DeWalt
- Messung Pioneer
- Messung Megasat
- Messung Smartwares
- Messung Garmin
- Messung GOCLEVER
- Messung Perel
- Messung Workzone
- Messung Microlife
- Messung Rossmax
- Messung Amprobe
- Messung Meec Tools
- Messung Metrix
- Messung IHealth
- Messung Ansmann
- Messung Westfalia
- Messung Livington
- Messung Silverline
- Messung Yato
- Messung Be Cool
- Messung Toolland
- Messung AS Schwabe
- Messung Hager
- Messung Kyoritsu
- Messung Eurolite
- Messung GW Instek
- Messung KERN
- Messung Milwaukee
- Messung Eizo
- Messung Testo
- Messung Victron Energy
- Messung Peak
- Messung KĂŒbler
- Messung Carrier
- Messung Lund
- Messung SHX
- Messung Gima
- Messung Testboy
- Messung Danfoss
- Messung Fantini Cosmi
- Messung Multimetrix
- Messung BENNING
- Messung Fluke
- Messung FLIR
- Messung Vemer
- Messung Oregon Scientific
- Messung Ridgid
- Messung Stabila
- Messung Hikmicro
- Messung Entes
- Messung Gossen Metrawatt
- Messung Hameg
- Messung Joy-it
- Messung Megger
- Messung Muller
- Messung PCE Instruments
- Messung RK Technology
- Messung Sanwa
- Messung Sonel
- Messung Uni-T
- Messung VirtuFit
- Messung Wachendorff
- Messung TFA Dostmann
- Messung Vimar
- Messung Owon
- Messung PeakTech
- Messung Comark
- Messung Dahua Technology
- Messung YSI
- Messung Aluratek
- Messung SRS
- Messung Eltako
- Messung H-Tronic
- Messung HT Instruments
- Messung Beha-Amprobe
- Messung Chauvin Arnoux
- Messung Werma
- Messung Eastron
- Messung Emko
- Messung Pancontrol
- Messung X-Rite
- Messung CESYS
- Messung Trumeter
- Messung Kemo
- Messung ORNO
- Messung Tempest
- Messung TDE Instruments
- Messung Zircon
- Messung Kreg
- Messung Apollo Ultrasonic
- Messung BJZ
- Messung Adwa
- Messung Greisinger
- Messung Qubino
- Messung Beckmann & Egle
- Messung WeidmĂŒller
- Messung Janitza
- Messung CEM
- Messung Klein Tools
- Messung Daytronic
- Messung AREXX
- Messung Delta Ohm
- Messung Camille Bauer
- Messung Rigel Medical
- Messung UHoo
- Messung Seaward
- Messung AstroAI
- Messung P3 International
- Messung Seek Thermal
- Messung ClimeMET
- Messung Fixpoint
- Messung Condtrol
- Messung Cliff
- Messung Water-i.d.
- Messung Stahlwille
- Messung KS Tools
- Messung AkYtec
Neueste Bedienungsanleitung fĂŒr -Kategorien-
4 August 2024
24 Juni 2024
24 Juni 2024
23 Juni 2024
23 Juni 2024
23 Juni 2024
23 Juni 2024
22 Juni 2024
21 Juni 2024
21 Juni 2024