Extech 380396 Bedienungsanleitung
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Extech 380396 (17 Seiten) in der Kategorie Messung. Dieser Bedienungsanleitung war für 2 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/17
User Manual
Digital High Voltage Insulation Tester
Model 380395 380396 or
2 380395_380396- - _V1.5 /en US 10 23
Introduction
Congratulations on your purchase of the Extech 380395 (120V) or 380396 (220V) High Voltage Insulation
Tester is meter provides four Insulation Resistance test ranges plus Continuity, AC/DC Voltage, . Th
Polarization Index and Dielectric Absorption Ratio measurements. This meter is shipped fully tested and
calibrated and, with proper care and , will provide years of reliable service. use
Features
• Auto ranging 6000 count LCD display with bargraph
• Selectable LCD backlight level function facilitates working dimly illuminated areas. in
• MAX/MIN, PEAK, Relative, and Data hold functions for DC/AC voltage measurements.
• Designed to the following safety standards:
IEC 61010-1 (CAT IV 600V Pollution degree 2)
IEC 61010-031 (Requirements for hand-held probes)
• Insulation test range: 0. 61MΩ to 0GΩ.
• Insulation test voltages: 500 0V, 100 V, 1 5 . 500V, and 000V
• AC/DC voltage: 0.5 V to 600 V.
• 200mA Continuity.
• Resistance: 0.1 Ω to 6kΩ.
• Auto-discharge function & voltage output warning function.
• E cally discharged after measurements. Discharge lectric charges stored in capacitive circuits are automati
status can be check using the real time voltage graph. ed bar
• LIVE circuit warning symbols plus audible warning.
• Live circuit detection prevents insulation test if voltage > 30 V is detected.
• Auto-power off function and battery check.
• Programmable Test Timer measurement function.
• Polarization Index measurement (PI).
• Dielectric Absorption Ratio measurement (DAR).
• Power source: Eight (8) 1.5V ‘C’ Cell Batteries.
3 380395_380396- - _V1.5 /en US 10 23
Safety
International Safety Symbols
This symbol, adjacent to another symbol or terminal, indicates the user must refer to the manual for
further information.
This symbol, adjacent to a terminal, indicates that, under normal use, hazardous voltages may be
present.
Danger: identifies conditions and actions that pose hazard(s) to the user.
Warning: alerts the user to avoid electric shock.
Caution: identifies conditions and actions that may damage the Insulation Resistance tester.
Operating Caution: identifies conditions where the user needs to take extra care during the
operation of the Insulation resistance tester
Danger: Use of this instrument in a manner not specified by the manufacturer may impair safety
features/protection provided by the equipment. Read all of the safety information carefully before
using or servicing the instrument.
This symbol indicates that the meter uses double or reinforced insulation.
Safety Notes
• Do not exceed the maximum allowable input range for any functions. of the meter’s
• Set the function switch OFF when the meter is not in use.
• Remove the batteries the meter is to be stored for longer than 60 days.if
Warnings
• Set the function switch to the appropriate position before measuring.
• Do not measure current on a circuit whose voltage exceeds 600V.
• When changing ranges always disconnect the test leads from the circuit under test.
• Do not use the Insulation resistance tester if it is damaged or if metal parts are exposed. Also, check
the meter for cracks or missing plastic.
• Be careful when working above 30V AC rms or 30V DC. Such voltages pose a shock hazard. Discharge all
circuit loads under test after measuring high voltage.
• Do not replace the batteries with the tester in a wet environment.
• Place the test leads in the proper input terminals. Ensure that the test leads are firmly connected to the
Insulation Resistance tester’s input terminals.
• Ensure that the Insulation Resistance tester is switched off when opening the battery compartment.
Produktspezifikationen
| Marke: | Extech |
| Kategorie: | Messung |
| Modell: | 380396 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Extech 380396 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Messung Extech
19 Juni 2024
19 Juni 2024
5 Juni 2024
29 Mai 2024
22 April 2024
21 April 2024
14 April 2024
7 April 2024
31 März 2024
10 März 2024
Bedienungsanleitung Messung
- Messung Hama
- Messung REV
- Messung Voltcraft
- Messung Bosch
- Messung Laserliner
- Messung Velleman
- Messung Powerfix
- Messung Alecto
- Messung Beurer
- Messung Bresser
- Messung König
- Messung TFA
- Messung Black And Decker
- Messung Trotec
- Messung DeWalt
- Messung Pioneer
- Messung Megasat
- Messung Smartwares
- Messung Garmin
- Messung GOCLEVER
- Messung Perel
- Messung Workzone
- Messung Microlife
- Messung Rossmax
- Messung Amprobe
- Messung Meec Tools
- Messung Metrix
- Messung IHealth
- Messung Ansmann
- Messung Westfalia
- Messung Livington
- Messung Silverline
- Messung Yato
- Messung Be Cool
- Messung Toolland
- Messung AS Schwabe
- Messung Hager
- Messung Kyoritsu
- Messung Eurolite
- Messung GW Instek
- Messung KERN
- Messung Milwaukee
- Messung Eizo
- Messung Testo
- Messung Victron Energy
- Messung Peak
- Messung Kübler
- Messung Carrier
- Messung Lund
- Messung SHX
- Messung Gima
- Messung Testboy
- Messung Danfoss
- Messung Fantini Cosmi
- Messung Multimetrix
- Messung BENNING
- Messung Fluke
- Messung FLIR
- Messung Vemer
- Messung Oregon Scientific
- Messung Ridgid
- Messung Stabila
- Messung Hikmicro
- Messung Entes
- Messung Gossen Metrawatt
- Messung Hameg
- Messung Joy-it
- Messung Megger
- Messung Muller
- Messung PCE Instruments
- Messung RK Technology
- Messung Sanwa
- Messung Sonel
- Messung Uni-T
- Messung VirtuFit
- Messung Wachendorff
- Messung TFA Dostmann
- Messung Vimar
- Messung Owon
- Messung PeakTech
- Messung Comark
- Messung Dahua Technology
- Messung YSI
- Messung Aluratek
- Messung SRS
- Messung Eltako
- Messung H-Tronic
- Messung HT Instruments
- Messung Beha-Amprobe
- Messung Chauvin Arnoux
- Messung Werma
- Messung Eastron
- Messung Emko
- Messung Pancontrol
- Messung X-Rite
- Messung CESYS
- Messung Trumeter
- Messung Kemo
- Messung ORNO
- Messung Tempest
- Messung TDE Instruments
- Messung Zircon
- Messung Kreg
- Messung Apollo Ultrasonic
- Messung BJZ
- Messung Adwa
- Messung Greisinger
- Messung Qubino
- Messung Beckmann & Egle
- Messung Weidmüller
- Messung Janitza
- Messung CEM
- Messung Klein Tools
- Messung Daytronic
- Messung AREXX
- Messung Delta Ohm
- Messung Camille Bauer
- Messung Rigel Medical
- Messung UHoo
- Messung Seaward
- Messung AstroAI
- Messung P3 International
- Messung Seek Thermal
- Messung ClimeMET
- Messung Fixpoint
- Messung Condtrol
- Messung Cliff
- Messung Water-i.d.
- Messung Stahlwille
- Messung KS Tools
- Messung AkYtec
Neueste Bedienungsanleitung für -Kategorien-
4 August 2024
24 Juni 2024
24 Juni 2024
23 Juni 2024
23 Juni 2024
23 Juni 2024
23 Juni 2024
22 Juni 2024
21 Juni 2024
21 Juni 2024