Emko ESM-9944-N Bedienungsanleitung
Emko
Temperaturregler
ESM-9944-N
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Emko ESM-9944-N (2 Seiten) in der Kategorie Temperaturregler. Dieser Bedienungsanleitung war für 15 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/2
ESM-9944-N / ESM-9945-N
COOKING CONTROLLERS
Electr cal W r ngs� � �
D mens ons� �
ESM-9945-N
SET
°C
°F
P
O1
O2
+ -
Temperature Un t Ind cator� �
Programm ng Mode Ind cator� �
Temperature Control Output Status
T me End Output Status�
Encoder Button
Temperature Ind cator�
Steam Output Status(ESM9945N)
T me nd cator� � �
Steam Start-Stop Button
(ESM9945N)
T me Start-Stop Button�
If cooking time is not active, starts
cooking time. If cooking time is
started, cooking time is cancelled
and buzzer is silenced.
Temperature Un t Ind cator� �
Front Panel Def n t on� � �
ESM-9945-N
SET
°C
°F
P
O1
O2
+ -
96 mm / 3.78 nch�
96 mm / 3.78 nch�
84 mm / 3.31 nch�
11.5 1mm / 0.45 nch�
Max mum 15 mm / 0.59 nch� �
Panel Cut-out
92 mm / 3.62 nch(m n)� �
92 mm / 3.62 nch(m n)� �
129 mm / 5.08 nch(m n)� �
129 mm / 5.08 nch(m n)� �
Panel Mount ng�
Access and Change Set Value
Temperature Set Value
Time Set Value
Note : If no operat on for 10 seconds, dev ce automat cally ex ts from Set Value Screen w thout sav ng the value.� � � � � �
Press encoder button
to observe the set value.
Turn left encoder button
to decrease or turn r ght �
to ncrease the set value.�
Press encoder button
to save new set value
and return ma n screen. �
+
°C
°F
P
O1
O2
++
Set Value Screen
SET
ESD-995 0-N
+
°C
°F
P
O1
O2
++
Ma n ScreenMa n Screen ��
+
°C
°F
P
O1
O2
++
Set Value Screen
+
°C
°F
P
O1
O2
++
Press encoder button
to observe the set value.
SET
+
°C
°F
P
O1
O2
++
Set Value Screen
Press encoder button
to save new set value
and return main screen.
Turn left encoder button
to decrease or turn right
to increase the set value.
SET
Ma n Screen�
+
°C
°F
P
O1
O2
++
SET
Set Value Screen
+
°C
°F
P
O1
O2
++
Ma n Screen�
+
SET
°C
°F
P
O1
O2
++
ESM-9944-N / ESM-9945-N Cook ng Controllers�
- 4 d g ts d splay� � �
- J type Thermocouple Input or
K type Thermocouple Input or
R type Thermocouple Input or
S type Thermocouple Input or
2 or 3 w re PT 100 Input �
- Adjustable Process Offset Value
- Programmable ON/OFF, P, PI, PD ve PID control types
- Adaptat on of PID coeff c ents to the system by Auto Tune/Self Tune� � �
- Work ng t me select on n m nutes or seconds� � � � �
- Vo ced warn ng v a nternal buzzer� � � �
- Cover sw tch nput� �
- Steam output (ESM-9945-N)
ESM-9944-N / ESM-9945-N cook ng controllers are ma nly used for Bakery � �
appl cat ons, fermantat on cab nets, ceram cs and glass ovens, gra n dr er � � � � � � �
cab net, ndustr al fryer, ncubators. Accurate and advanced controll ng s � � � � � �
performed w th selectable ON-OFF, P, PI, PD ve PID, Self-Tune PID, Auto-�
Tune PID funct ons.�
DISPLAY
Temperature D splay:� 16 mm Red 4 d g ts LED D splay� � �
Led Ind cators:� O1 (Temperature Control Output Status LED), O2 (T me Control �
Output Status LED), Steam Output LED(ESM-9945-N), T me Ind cator, � �
Temperature Ind cator, P(Programm ng Mode LED),ºC, ºF LEDs� �
OUTPUT
Temperature Control Output : Relay (7A@250V at res st ve load) or opt onal V� � �
SSR Dr ver Output (Max mum 10mA, 17V )� � Z
T me Output : �Relay (5A@250V at res st ve load) or opt onal SSR Dr ver V� � � �
Output (Max mum 10mA, 17V )�Z
Steam Output(ESM-9945) : Relay (5A@250V at res st ve load) or opt onal V� � �
SSR Dr ver Output (Max mum 10mA, 17V )� � Z
Bes des these, there � �s an �nternal buzzer for vo ced warn ng.� �
SPECIFICATIONS
INPUT
Process Input: TC/RTD
Thermocouple (TC): J, K, R and S (IEC584.1)(ITS90)
Thermores stance (RTD):� 2 or 3 w re Pt100 ( IEC 751) (ITS90)�
Measurement Range: Please refer to parameter n parameters sect on.� �
Accuracy: ± 0.25% of scale for thermocouple and thermores stance.�
Cold Junct on Compensat on:� � Automat cally ±0.1°C/1°C�
L ne Compensat on: � � Max mum 10 Ohm�
Sensor Break Protect on:� Upscale
Sampl ng Cycle: �0.1 second
CONTROL
Control Forms: ON/OFF, P, PI, PD veya PID (Control form can be
programmed by the user.)
SUPPLY VOLTAGE
230V (±15%) 50/60Hz - 3VAV
115V (±15%) 50/60Hz - 3VAV
24V (±15%) 50/60Hz - 3VAV
(Must be determ ned � �n order.)
ENVIRONMENTAL RATINGS and PHYSICAL SPECIFICATIONS
Operat ng Temperature:� 0...50ºC
Hum d ty :� � 0-90%RH (none condens ng)�
Protect on Class: �IP65 at front , IP20 at rear
We ght: � 370 gr.
D mens on: � � 96 x 96 mm, Depth: 100 mm
Panel CutOut: 92 x 92 mm
To reduce the effect of electr cal no se on dev ce, low voltage l ne (espec ally sensor � � � � �
� � � � �nput cables) w r ng must be separately from h gh current and voltage l ne. If
poss ble, use sh elded cable abd sh eld must be connected to ground only one s de.� � � �
Output-1
TC
PT-100
4 5 10 11 12 13 14 15
Output-2
7A@250V 5A@250V 5A@250VV V V
6 7 8 9
D g tal Input� �
Output-3
NCCNO CNO CNO
ESM-9945-N
CAT II
O2
(T me End �
Output)
O1
(Temperature Control
Output)
Supply
Voltage
Sw tch�
N
Supply
Voltage
L
1A T
S gorta�O3
(Steam
Output)
Cover
Sw tch�
Temperature
Sensor Input
Output-1
TC
PT-100
4 5 10 11 12 13 14 15
Output-2
7A@250V 5A@250VV V
6 7 8 9
D g tal Input� �
NCCNO CNO
ESM-9944-N
CAT II
O2
(T me End�
Output)
O1
(Temperature Control
Output)
Supply
Voltage
Sw tch�
N
Supply
Voltage
L
1A T
S gorta�Cover
Sw tch�
Temperature
Sensor Input
Instruct on Manual. ENG ESM-994X-N 01 V02 02/18�
1- Before mount ng the dev ce n your panel, make � � �
sure that the cutouts s of the r ght s ze.� � �
2- Check front panel gasket pos t on.� �
3- Insert the dev ce through the cutout. If the �
mount ng clamps are on the un t, put out them before � �
� � �nsert ng the un t to the panel.
4- Insert the mount ng clamps to the two of �
des gnated holes that located on four s des of dev ce.� � �
5- Drag the mount ng clamps n d rect on 5 unt l the � � � � �
dev ce completely mmob le w th n the panel.� � � � �
6- In order to remove dev ce push on the mount ng � �
clamp as shown w th arrow 6 and pull back.�
3
2
1
4
5
Access the Parameters
SET
+
°C
°F
P
O1
O2
++
Press encoder
button dur ng 10 seconds. �
Ma n Screen�
SET
+
°C
°F
P
O1
O2
++
Press encoder
button dur ng 10 seconds. �
Ma n Screen�
SET
If no pr vacy lock dent f cat on � � � � �
Parameters Screen w ll be �
observed. If pr vacy lock s � �
� � � �dent f ed, w ll be observed.
Press encoder button to access
Password Screen.
+
°C
°F
P
O1
O2
++
Enter the password using
encoder button. Turn left
encoder button to decrease or
turn right to increase value.
Approve password using
encoder button.
+
°C
°F
P
O1
O2
++
Password Screen
If Parameters Screen is
active, "P" led blinks. To
observe previous parameter,
turn encoder button left. To
observe next parameter, turn
encoder button right. Press
encoder button to observe
parameter value.
+
°C
°F
P
O1
O2
++
Parameters Screen
: Process nput type select on parameter. (Default: ) � �
J type (Fe,Cu,N ) Thermocouple; -200ºC,900ºC ; -328ºF,1652ºF�
J type (Fe,Cu,N ) Thermocouple; -199.9ºC,900.0ºC ; -199.9ºF,999.9ºF�
K type (N ,Cr,N ) Thermocouple; -200ºC,1300ºC ; -328ºF,2372ºF� �
K type (N ,Cr,N ) Thermocouple; -199.9ºC,999.9ºC ; -199.9ºF,999.9ºF� �
R type (Pt13%RhPt) Thermocouple; 0ºC,1700ºC ; 32ºF,3092ºF
R t p (Pt13%RhPt) Thermocouple; 0.0ºC,999.9ºC ; 32.0ºF,999.9ºF� �
S t p (Pt10%RhPt) Thermocouple; 0ºC,1700ºC ; 32ºF,3092ºF� �
S t p (Pt10%RhPt) Thermocouple; 0.0ºC,999.9ºC ; 32.0ºF,999.9ºF� �
PT100 Thermores stance; -200ºC,650ºC ; -328ºF,1202ºF�
PT100 Thermores stance; -199.9ºC,650.0ºC ; -199.9ºF,999.9ºF�
: Un t select on parameter. or can be chosen. (Default: )� �
: Operat on scale m n mum(Low L m t) value. It changes accord ng to � � � � � �
the process nput type and scale. (Default: -200) �
: Operat on scale max mum(H gh L m t) value. It changes accord ng to � � � � � �
the process nput type and scale. (Default: 900) �
: Process set value low l m t parameter. It can be adjusted between � �
Operat on Scale M n mum( ) and Process Set Value H gh L m t( ).� � � � � �
(Default:-200)
: Process set value h gh l m t parameter. It can be adjusted between � � �
Process Set Value Low L m t( ) and Operat on Scale Max mum( ) � � � �
and (Default: 900)
: Process offset value. It can be adjusted as a degree( or ), from
-10% of scale to 10% of scale.It s added to the process value. (Default: 0)�
: Output control type parameter. It can be selected or .
(Default: )
: Hysteres s value. It can be adjusted from 1º(po nt representat on:� � �
0.1º) to 20º. (Default: 3)
: M n mum ON/OFF control output t me parameter. It can be adjusted � � �
from 0 to 60 seconds. (SSR Default: 0 ; Relay Default: 5)
: Proport onal band (P). It can be adjusted from %1.0 to %100.0.�
(Default: 10.0)
: Output Control Per od. If control output s SSR, It can be adjusted � �
from 0.5 to 150.0 seconds. If control output s Relay, It can be adjusted 60.0 �
to 150.0 seconds. (SSR Default: 10.0 ; Relay Default: 60.0)
: Proport onal Offset value. Th s parameter s used for sh ft ng the � � � � �
proport onal band. It can be adjusted from (-Operat on Scale Max mum /2) � � �
to (Operat on Scale Max mum /2). (Default: 0)� �
: Integral T me. It can be adjusted from 0 to 3600 seconds. �
(Default: 100)
: Der vat ve T me. It can be adjusted from 0.0 to 999.9 seconds.� � �
(Default: 25.0)
Bak mı
Adjustment of Hysteres s Value for ON/OFF Control�
Time
Time
Temperature
Set Value
Temperature
Control Output
Temperature
Hysteresis
In ON/OFF control algor thm, temperature value s tr ed to keep equal to set � � �
value by open ng or clos ng completely last control element. ON/OFF controlled � �
system, temperature value osc llates cont nuously. Temperature value’s � �
osc llat on per od or ampl tude around set value changes accord ng to controlled � � � � �
system. For reduc ng osc llat on per od of temperature value, a threshold zone � � � �
� � � � �s formed below or around set value and th s zone s named hysteres s. Act on
of control output s descr bed w th f gures below.� � � �
Temperature
Control Output
Temperature
Set Value
Temperature
ON/OFF
Conrol Form
with
Hysteresis
Other Informat ons�
Manufacturer Informat on:�
a
Emko Elektron k Sanay ve T caret A. .� � � Ş
Dem rta Organ ze Sanay Bölges Karanf l Sk. No:6 16369 � ş � � � �
BURSA/TURKEY
a
Phone : +90 224 261 1900
Fax : +90 224 261 1912
a
Repa r and Ma ntenance Serv ce Informat on:� � � �
a
Emko Elektron k Sanay ve T caret A. .� � � Ş
Dem rta Organ ze Sanay Bölges Karanf l Sk. No:6 16369 � ş � � � �
BURSA/TURKEY
a
Phone : +90 224 261 1900
Fax : +90 224 261 1912
Order ng Informat ons� �
Supply VoltageA
Customer
3
4
5
9
24V (±%15) 50/60HzV
115V (±%15) 50/60HzV
230V (±%15) 50/60HzV
Input TypeBC
Conf gurable20 �
Scale
See Parameters ( )
In package,
-One piece unit
-Two pieces mounting clamp
-One piece instruciton manual
A visual inspection of this product for possible damage occured
during shipment is recommended before installation. It is your
responsibility to ensure that quali ed mechanical and electrical fi
technicians install this product.
If there is danger of serious accident resulting from a failure or
defect in this unit, power o the system and the electrical ff
connection of the device from the system.
The unit is normally supplied without a power switch or a fuse.
Use power switch and fuse as required.
Be sure to use the rated power supply voltage to protect the unit
against damage and to prevent failure.
Keep the power o until all of the wiring is completed so that ff
electric shock and trouble with the unit can be prevented.
Never attempt to disassemble, modify or repair this unit.
Tampering with the unit may results in malfunction, electric shock
or re.fi
Do not use the unit in combustible or explosive gaseous
atmospheres. During the equipment is put in hole on the metal
panel while mechanical installation some metal burrs can cause
injury on hands, you must be careful.
Montage of the product on a system must be done with it's
mounting clamp. Do not do the montage of the device with
inappropriate mounting clamp. Be sure that device will not fall
while doing the montage.
It is your responsibility if this equipment is used in a manner not
speci ed in this instruction manual.fi
Before beg nn ng nstallat on of th s product, please read � � � � �
the nstruct on manual and warn ngs below carefully.� � �
Installat on�
Warranty
EMKO Elektronik warrants that the equipment delivered is free from defects
in material and workmanship. This warranty is provided for a period of two
years. The warranty period starts from the delivery date.
This warranty is in force if duty and responsibilities which are
determined in warranty document and instruct on manual performs by the
customer completely.
Ma ntenance�
Repairs should only be performed by trained and specialized personnel. Cut
power to the device before accessing internal parts. Do not clean the case
with hydrocarbon-based solvents (Petrol, Trichlorethylene etc.). Use of
these solvents can reduce the mechanical reliability of the device. Use a
cloth dampened in ethyl alcohol or water to clean the external plastic
case.
Before comm ss on ng the dev ce, parameters must be set n� � � � �
accordance w th des red use. Incomplete or ncorrect conf gurat on� � � � �
can cause dangerous st uat ons.� �
Because of l m ted mechan cal l fe of relay output contact, SSR output � � � �
� � � �s recommended wh ch the dev ce use PID control algor tm. The
dev ce w th ON/OFF control algor tm, hysteres s parameter must be � � � �
set a su table value for your system, to avo d too much relay sw tch ng.� � � �
V Vac,→
Z Vdc,→
W Vdc or Vac can be appl ed.→ �
Output-1 (Temperature Control Output)E
Relay Output (7A@250V at Res st ve Load) (NO,NC,C) V� �
1
SSR Dr ver Output (Max. 10mA, 17V ) �Z
2
Output-2 (T me Output)�FG
Relay Output (5A@250V at Res st ve Load) (NO,C) V� �
01
SSR Dr ver Output (Max. 10mA, 17V ) �Z
02
Output-3 (Steam Output) (ESM-9945-N)HI
Relay Output (5A@250V at Res st ve Load) (NO,C) V� �
01
SSR Dr ver Output (Max. 10mA, 17V ) �Z
02
ESM-9945-N(96x96 DIN 1/4)
20
0 1
ESM-9944-N(96x96 DIN 1/4)
20
0
00
1
Access, Change and Record the Parameter Values
: If tune parameter s set to or , dev ce starts to calculate� �
PID parameters automat cally. (Default: ) �
: Dev ce does not calculate PID parameters.�
: Step Response Tun ng operat on.� �
: L m t Cycle Tun ng operat on.� � � �
:Temperature - T me d splay form. If parameter value set as ,only � �
Temperature or T me value s d splayed accord ng to selected page. If � � � �
parameter value set as d fferent from , Temperature and T me value s � � �
d splayed alternately dur ng parameter value. It can be adjusted from � �
0 to 99 seconds. (Default: )
: T mer d splayed form. If parameter value set as , t mer form s � � � �
M nute-Second. If parameter value set as , t mer form s Hour-M nute. � � � �
(Default: )
: T mer counts d rect on parameter. If the parameter set as , t mer � � � �
counts downt-to-up. If the parameter set as , t mer counts up-to-down.�
(Default: )
: T mer count ng method parameter. If the parameter set as , t mer� � �
counts act ve t me. If the parameter set as , t mer counts set t me. � � � �
If parameter set as , th s parameter s not seen. (Default: ) � �
: T mer Relay Pos t on Parameter. If the parameter s , T mer relay � � � � �
becomes act ve pos t on w th the t me start and becomes pass ve at the � � � � � �
end of the t me. If the parameter s , then t me relay becomes act ve at � � � �
the end of the t me. (Default: )�
: Relay act ve t me parameter. If parameter value set as then � �
T me End Output w ll be act ve cont nously. If value set as a d fferent � � � � �
value(from 1 to 9999 seconds), T me End Output w ll be act ve dur ng the � � � �
entered t me. (Default: )�
: Buzzer act ve t me parameter. If parameter value set as , � �
Buzzer w ll be act ve cont nously. If parameter value set as a d fferent � � � �
value (from 1 to 9999 seconds), Buzzer w ll be act ve dur ng the entered � � �
t me. (Default: )�
: D g tal nput c rcu t parameter. If the parameter set as , c rcu t s � � � � � � � �
Normally Open (NO). If the parameter set as , c rcu t s Normally Closed � � �
(NC). (Default: )
: Type of command when d g tal nput act vated. If the parameter set � � � �
as , t mer stops count ng and resets t me. If the parameter set as , � � �
t mer pauses count ng. (Default: )� �
: Steam durat on parameter (ESM9945N). If the Steam Durat on � �
Parameter s selected as then the steam output w l be on dur ng the � � �
Steam button s pressed. If the parameter value set as a d fferent value� �
(from 1 to 9999 seconds), after press ng the steam button, output w ll be � �
on dur ng the Steam Durat on Parameter value. If Steam button s � � �
pressed when steam output s on, steam output w ll be off. (Default: )� �
: Password for access ng to the parameters sect on. It can be � �
adjusted from 0 to 9999. If parameter value s , password screen s not � �
seen. If parameter value s d fferent from and ;� �
-If user enters d fferent value from saved value, dev ce w ll return to � � �
ma n screen automat cally.� �
-If user enters , all parameters can be observed except .
But dev ce does not allow to do any changes n parameters. (Default: )� �
Error Messages
Sensor fa lure n analog nput. If there s no � � � �
sensor connect on or the value that s read from � �
the analog nput goes out of the dev ce scale, � �
warn ng s observed.� �
ESM-9945-N
SET
°C
°F
P
O1
O2
+ -
ESD-9950-N
SET
°C
°F
P
O1
O2
+ -
S
Tune fa lure. If s selected n PID Tune � � �
Parameter( ) and start cond t ons are not � �
okay for Tune operat on, the temperature value �
� � �s d splayed alternately w th message on
d splay dur ng 10 seconds.� �
Parameters Descr pt ons� �
Start ng the Tune operat on� �
1- Enter the parameter and select or . Observe that bl nks.�
(If s selected and start cond t ons are not okay for Tune operat on, � � � �
bl nks dur ng 10 seconds.)� �
2- Dev ce calculates PID control coeff c ents and sets the process value to � � �
wanted value.
Cancell ng tune operat on:� �
1- If sensor breaks;
2-If tune operat on can not be completed n 8 hours;� �
3-Wh le tune operat on s runn ng, f process value becomes greater than � � � � �
process set value;
4-Wh le tune operat on s runn ng, f user changes the process set value;� � � � �
5-Wh le tune operat on s runn ng, f user changes the parameter n menu;� � � � � �
Then tune operat on s canceled and dev ce cont nues to run w th former PID � � � � �
parameters w thout chang ng PID parameters.� �
Tune Operat on�
+
SET
°C
°F
P
O1
O2
++
Parameter Values Screen
To increase parameter
value, turn encoder button
right. Press encoder button
to save.
+
SET
°C
°F
P
O1
O2
++
Parameter Values Screen
To decrease parameter
value, turn encoder button
left. Press encoder button
to save.
+
SET
°C
°F
P
O1
O2
++
Parameters Screen
+
SET
°C
°F
P
O1
O2
++
Parameters Screen
Turn encoder button
left to observe
previous parameter or
turn right to observe
next parameter.
Turn encoder button
left to observe
previous parameter or
turn right to observe
next parameter.
Note1: PID control parameters ( , , , , , ) are not seen when
output control type parameter ( ) s set as .�
Note2: ON/OFF control parameters ( , ) are not seen when output control type
parameter ( ) s set as .�
Note3: parameter s not seen when parameter set as . parameter can be �
seen after parameter.
Note4: parameter s not seen n ESM9944N dev ce. parameter can be seen after � � �
parameter.
Note5: If s d fferent from and user enters on password screen, parameter values � �
except are observed but can not be changed.
Note6: If no operat on for 20 seconds on Parameters Screen, dev ce automat cally returns � � �
Ma n Screen .�
Produktspezifikationen
| Marke: | Emko |
| Kategorie: | Temperaturregler |
| Modell: | ESM-9944-N |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Emko ESM-9944-N benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Temperaturregler Emko
31 August 2024
31 August 2024
31 August 2024
28 August 2024
28 August 2024
28 August 2024
28 August 2024
19 August 2024
15 August 2024
14 August 2024
Bedienungsanleitung Temperaturregler
- Temperaturregler Voltcraft
- Temperaturregler Techno Line
- Temperaturregler Technoline
- Temperaturregler Ventus
- Temperaturregler Cocraft
- Temperaturregler Honeywell
- Temperaturregler Kathrein
- Temperaturregler Inkbird
- Temperaturregler Dimplex
- Temperaturregler JUNG
- Temperaturregler Davis
- Temperaturregler Bulex
- Temperaturregler Fluke
- Temperaturregler Opticlimate
- Temperaturregler ACV
- Temperaturregler Wachendorff
- Temperaturregler Ygnis
- Temperaturregler AstralPool
- Temperaturregler Jumo
- Temperaturregler Ziehl
Neueste Bedienungsanleitung für -Kategorien-
2 Oktober 2024
30 September 2024
28 September 2024
21 September 2024
20 September 2024
19 September 2024
5 September 2024
28 August 2024
28 August 2024
28 August 2024