Emko CHANNEL8A-N Bedienungsanleitung
Emko
Temperaturregler
CHANNEL8A-N
Lesen Sie kostenlos die š deutsche Bedienungsanleitung fĆ¼r Emko CHANNEL8A-N (4 Seiten) in der Kategorie Temperaturregler. Dieser Bedienungsanleitung war fĆ¼r 11 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/4
ENGī ī CHANNEL8A-Nī 01ī V00ī 03/17
CHANNEL8A-N
8ī CHANNEL ANALOGī SCANNER
96ī xī 96ī DINī 1/4
12ī Ā±ī 1ī mmī /ī 0.47ī inch 84ī mmī /ī 3.31ī inch
ī 15 0.59ī inchmmī /
92mm/3.62ī inch
92mm/3.62ī inch
129mm/5.08ī inch(min)
129mm/5.08ī inch(min)
320ī xī 240ī Pixel
TFT LCD
Standart
Function
Buttons
MENU BUTTON
Used to access Menu page.
ENTER BUTTON
Used to go in to selected page, to make parameter's cell
available toī change and to confirm parameterās change.
AUTO BUTTON
Used to auto-scan pages.
BACK BUTTON
Used to go back to previous menu and to cancel
parameter's change.
UP BUTTON
Used to go up in menus and lists and also used to increase
parameter's value.
LEFTī BUTTON
Usedī toī goī leftī inī menus.
DOWNī BUTTON
Usedī toī goī downinī menusī andī listsī andī alsoī usedī to
decreaseī parameter'sī value.
RIGHTī BUTTON
Usedī toī goī rightī inī menus.
F4
F1 F2 F3
DELETEī BUTTON
Usedī toī eraseī logsī onī theī screen.
SETTINGS
LOGS
ADVANCE
SETTINGS
LANGUAGE
CHANNEL8A-Nī 8ī Channel Analogī Scanner
-ī 320ī xī 240ī pixelī TFTī LCDī display
-ī 8 Analogī inputs
-ī ON-OFFī control
-ī Relayī orī (pnp āsourceā)ī transistorī output
-ī Sensorī errorī detection
- Adjustableī temperatureī offset
-ī 3ī Differentī alarmī andī pre-alarmī typesī forī eachī channel
(High,ī Lowī andī Band Alarms)
-ī Userī definedī channelī labels
-ī Displayī scanī modes
-ī Operatingī withī Realī Timeī Clockī (RTC)
-ī ModBusī RTUī communicationī protocol
(RS-232,ī RS-485ī andī Ethernetī communication)
-ī Dataī Loggingī toī USBī Flashī Memory
- Adjustableī dataī loggingī timeī interval
-ī Passwordī protectionī forī programmingī mode
CHANNEL8A-N series 8 channel analog scanner devices are designed
for measuring and logging temperature. They can be used in many
applications with their, alarm outputs, selectable alarm functions, RS-
232 / RS-485 / Ethernet / USB communications.
SPECIFICATIONS
INPUT
Analogī Inputsī :
Accuracyī :
Samplingī Timeī :
OUTPUT
Relayī :
DISPLAY
LCDī Displayī :
POWERī SUPPLY
ENVIRONMENTAL RATINGS
Operatingī Temperatureī :
Humidityī :
Protectionī Classī :
PHYSICAL SPECIFICATIONS
Weightī :
Dimension :
Panel Cut-Out :
0-20mA /ī 4-2ī mA andī 0-10VDC Analogue
Ā±ī 0.25%ī ofī fullī scale
400ī ms
ax.1A@24V
320x240
0...50Ā°C
0-90%RHī (noneī condensing)
IP65ī atī front,ī IP20ī atī rear
0ī gr.
96 x 96 mm, Depth:96 mm
92 x 92 mm
W
W
40
Resolutionī :
Inputī Ressistanceī :
Transistorī :
14ī Bits
100 forī 0-20mA inputī and
68k forī 0-10Vī input
Resistiveī Loadī 5A@250V
(Electricalī Lifeī :ī 100.000ī operationī (Fullī Load)
PNP(source)ī typeī transistorī outputī (M )
pixel TFT LCD
100ī -ī 240ī V (-%15ī /ī +%10)ī 50/60ī Hz.ī ī 7VA
24ī V (-%15ī /ī +%10)ī 50/60ī Hz.ī ī 7VA
24ī V (-%15ī /ī +%10)ī ī 7W
(Itī mustī beī determinedī inī order.)
V
Z
V
V
Z
Electricalī Wiringī Diagram
Deviceī withī Relayī Outputs
RSī 232
COMMUNICATION
5ī xī 5A@250V
COMMON-1
COMMON-2
16 21 22 23 24 25 26 27 28 29 3017 18 19 20
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
CH-1 ALARM
OUTPUT
CH-
OUTPUT
2 ALARM
CH-
OUTPUT
3 ALARM
CH-
OUTPUT
4 ALARM
CH-
OUTPUT
5 ALARM
CH-
OUTPUT
6 ALARM
CH-
OUTPUT
7 ALARM
CH-
OUTPUT
8 ALARM
GENERAL ALR.
OUTPUT
GENERAL PRE-ALR.
OUTPUT
5ī xī 5A@250V
USBī 2.0
COMMUNICATION
ETHERNET
OR
RS485
COMMUNICATION
CH-1CH-2CH-3CH-4CH-5CH-6CH-7CH-8
100...240Vī ī ī ī ī -ī %15;+%10)ī 50/60Hzī 7VA
24Vī ī ī ī ī ī (-%15;+%10)ī 50/60Hzī 7VA
24Vī ī ī ī ī ī (-%15;+%10)ī 7W
L
(+)
N
(-)
Deviceī withī Transistorī Outputs
RSī 232
COMMUNICATION
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
USBī 2.0
COMMUNICATION
ETHERNET
OR
RS485
COMMUNICATION
100...240Vī ī ī ī ī ī ī ī (-ī %15;+%10)ī 50/60Hzī 7VA
24Vī ī ī ī ī ī (-%15;+%10)ī 50/60Hzī 7VA
24Vī ī ī ī ī ī ī (-%15;+%10)ī 7W
L
(+)
N
(-)
iRS485, Ethernet and USB communications are optional
16 21 22 23 24 25 26 27 28 29 3017 18 19 20
CH-1 ALARM
OUTPUT
CH-
OUTPUT
2 ALARM
CH-
OUTPUT
3 ALARM
CH-
OUTPUT
4 ALARM
CH-
OUTPUT
5 ALARM
CH-
OUTPUT
6 ALARM
CH-
OUTPUT
7 ALARM
CH-
OUTPUT
8 ALARM
GENERAL ALR.
OUTPUT
GENEAL PRE- ALR.
OUTPUT
10ī xī 1A@24V
TRANSISTORī OUTPUTS
POWERī SUPPLY
24Vī ī ī ī ī ī ī ī ī ī Ā±%15
iRS485, Ethernet and USB communications are optional
Relayī Outputs
(Alarmī Outputsī for
Channelsī 6ī toī 8,
General Alarmī Outputī and
Generalī Pre-Alarmī Outputī )
CHī =ī CHANNEL
Powerī Supplyī Input
(Itī mustī beī determinedī inī order.)
Common1 Common2
Relayī Outputs
(Alarmī Outputsī for
Channelsī 1ī toī 5)
Powerī Supplyī Input
(Itī mustī beī determinedī inī order.)
Transistorī Outputs
(Alarmī Outputsī for
Channelsī 1ī toī 8,
General Alarmī Outputī and
Generalī Pre-Alarmī Outputī )
CHī =ī CHANNEL
Maximum
CHANNEL8A-NFrontī Viewī andī Dimensionsī of
Panelī Cut-Out
1-Before mounting the device
in your panel, make sure that
the cut-out is of the right size.
2-Check front panel gasket
position
3-Insert the device through the
cut-out. If the mounting clamps
are on the unit, put out them
before inserting the unit to the
panel.
Panelī Mounting
Installationī Fixingī Clamp
The unit is designed for panel
mounting.
1-Insert the unit in the panel
cut-out from the front side.
2- Insert the mounting clamps
to the holes that located top
and bottom sides of device and
screw up the fixing screws until
the unit completely immobile
within the panel.
Removingī fromī theī Panel
1-Loosen the screws.
2-Pull mounting clamps from
top and bottom fixing sockets.
3-Pull the unit through the
front side of the panel
Definitionī ofī Frontī Panel
AGND
Processī Inputs
(4-20mA /ī 0-20mA)
(0-10ī V)
ı
+
ı
+
ı
+
ı
+
ı
+
ı
+
ı
+
ı
+
ı
+
ı
+
0-20mA Z
0-10V Z
4-20mA Z
0-20mA Z
0-10V Z
4-20mA Z
0-20mA Z
0-10V Z
4-20mA Z
0-20mA Z
0-10V Z
4-20mA Z
0-20mA Z
0
-10VZ
4-20mA Z
0-20mA Z
0-10V Z
4-20mA Z
0-20mA Z
0-10V Z
4-20mA Z
0-20mA Z
0-10V Z
4-20mA Z
AGND
Processī Inputs
(4-20mA /ī 0-20mA)
(0-10ī V)
ı
+
ı
+
ı
+
ı
+
ı
+
ı
+
ı
+
ı
+
ı
+
ı
+
0-20mA Z
0-10V Z
4-20mA Z
0-20mA Z
0-10V Z
4-20mA Z
0-20mA Z
0-10 VZ
4-20mA Z
0-20mA Z
0-10V Z
4-20mA Z
0-20mA Z
0-10VZ
4-20mA Z
0-20mA Z
0-10V Z
4-20mA Z
0-20mA Z
0-10V Z
4-20mA Z
0-20mA Z
0-10V Z
4-20mA Z
CH-1CH-2CH-3CH-4CH-5CH-6CH-7CH-8
96ī mmī /ī 3.78ī inch
96ī mmī /ī 3.78ī inch
F1 F2 F3 F4
A
1
2
3
F1 F2 F 3 F4
A
1
2
F1 F2 F 3 F4
A
F4F1 F2 F3
A
3
1
2
F1 F2 F 3 F4
A
MAINī OPERATIONī SCREEN
MAINī OPERATIONī (CHANNEL-1ī SCREEN)
i
i
i
MENUī SCREEN
OPERATORī PARAMETERS
PASSWORDī SCREEN
Pressī F1ī orī F2ī directionī buttons
toī moveī toī theī Settingsī tab.
Whenī theī F1ī menuī buttonī isī pressed
whileī theī mainī screenī isī onī theī page,ī the
menuī pageī isī displayed.
PARAMETERS
CHANGE
PARAMETERS
CHANGE
OPERATORī PARAMETERS
(CHANNEL-1ī PARAMETERS)
Pressī F3ī button.ī Ifī password
isī differentī fromī 0,ī password
screenī opens.
Enterī theī passwordī valueī using
theī F1ī andī F2ī buttons.
Confirmī theī charactersī oneī by
oneī byī pressingī F3ī button.
Onceī youī haveī confirmedī the
lastī character,ī youī willī proceed
toī theī operatorī parameters
screen.
Pressī theī F1ī andī F2ī buttonsī to
highlightī theī channelī andī pressī theī F3
button.
Selectī theī relevantī parameter
withī theī F1ī andī F2ī buttons.
Pressī theī F3ī buttonī toī select
theī parameter.
Useī theī F1ī andī F2ī buttonsī toī change
theī valueī ofī theī parameter.
Pressī theī F3ī buttonī toī save
theī parameterī value.
DEVICEī SETTINGS
(Rs485ī SETTINGS)
DEVICEī SETTINGS
(USBī SETTINGS)
DEVICEī SETTINGS
(ETHERNETī SETTINGS)
DEVICEī SETTINGS
(DATEī TIMEī SETTINGS)
Withī theī F1ī andī F2ī buttonsī youī can
selectī andī changeī theī USB
parameters.ī Useī theī F3ī buttonī to
save.
Withī theī F1ī andī F2ī buttonsī youī can
selectī andī changeī theī RS485
parameters.ī Useī theī F3ī buttonī to
save.
Withī theī F1ī andī F2ī buttonsī youī can
selectī andī changeī theī ETHERNET
parameters.ī Useī theī F3ī buttonī to
save.
Withī theī F3ī buttonī youī canī selectī the
Dateī and Timeī parametersī andī you
canī changeī theī valueī withī theī F1,ī F2
buttons.
i
i
i
Channelī Number
Deviceī Function
Buttons
Alarm Set
Alarm set value for selected channel is can be adjusted according to this parameter.
It can be adjust between -200 0
O O
C to +65 C.
Pre. Alarm Set
Pre- Alarm set value for selected channel is can be adjusted according to this
parameter. It can be adjust between -200 0
O O
C to +65 C.
i
F4F1 F2 F3
Channelī Label
PreAlarmī Status
Alarmī Status
Channelsī Names
Processī Value
F4F1 F2 F3
F4F1 F2 F3
Alarmī Messages
Channelī Output
Status
Channelī Number
F4F1 F2 F3 F4F1 F2 F3
F4F1 F2 F3 F4F1 F2 F3
F4F1 F2 F3 F4F1 F2 F3
F4F1 F2 F3 F4F1 F2 F3
F4F1 F2 F3F4F1 F2 F3
F4F1 F2 F3 F4F1 F2 F3
F4F1 F2 F3 F4F1 F2 F3
F4F1 F2 F3
F1
F1 F2
F3
F1
F2
F3
F1
F2
F1
F2 F3
F1
F2
Operatorī Passwordī Change
Passwordī forī deviceī isī adjustedī byī thisī parameter.Operator
DEVICEī SETTINGS
(PASSWORDī CHANGE)
Useī theī F1ī andī F2ī buttonsī toī change
theī valueī ofī theī parameter.ī Confirmī the
charactersī oneī byī oneī byī pressingī F3
button.
Useī theī F1ī buttonī toī moveī to
theī "YES"ī tabī andī pressī theī F3
button.ī Inī 1-3ī secondsī the
deviceī willī returnī toī factory
settings.
F4F1 F2 F3 F4F1 F2 F3
TECHNICIANī PARAMETERS
(CONTROL PARAMETERS
TECHNICIANī PARAMETERS
PASSWORDī SCREEN
TECHNICIANī PARAMETERS
PASSWORDī SCREEN
TECHNICIANī PARAMETERS
PASSWORDī INPUTī SCREEN
Pressī F1ī orī F2ī directionī buttons
toī moveī toī the Advanced
Settingsī tab.
PARAMETERS
CHANGE
DEVICEī SETTINGS
(RS232ī SETTINGS)
Pressī F3ī button.ī Ifī password
isī differentī fromī 0,ī password
screenī opens.
Enterī theī passwordī valueī using
theī F1ī andī F2ī buttons.
Confirmī theī charactersī oneī by
oneī byī pressingī F3ī button.
Onceī youī haveī confirmedī the
lastī character,ī youī willī proceed
toī theī operatorī parameters
Useī theī F1ī andī F2ī buttonsī toī scrollī to
theī Controlī parametersī andī pressī the
F3ī button.
Selectī theī relevantī channelī withī theī F1
andī F2ī buttons.
Pressī theī F3ī buttonī toī select
theī parameter.
Useī theī F1ī andī F2ī buttonsī toī change
theī valueī ofī theī parameter.ī Pressī the
F3ī buttonī toī saveī theī parameterī value.
Withī theī F1ī andī F2ī buttonsī you
canī selectī andī changeī theī RS232
parameters.ī Useī theī F3ī buttonī to
save.
F4F1 F2 F3 F4F1 F2 F3
F4F1 F2 F3 F4F1 F2 F3
F4F1 F2 F3 F4F1 F2 F3
F4F1 F2 F3 F4F1 F2 F3
F4F1 F2 F3F4F1 F2 F3
F1
F1 F2
F3
F1
F2
F3
F1
F2
F1
F2 F3
F3
F3
F3
F3
TECHNICIANī PARAMETERS
(CHANNEL-1)
TECHNICIANī PARAMETERS
(CHANNEL-1ī PARAMETERS)
Mainī Operationī Screensī Definetion Accessingī toī theī Operatorī Parameterī Pages
Ifī theī displayī typeī parameterī valueī ī Screenī Typeī =ī MULTIPLE
If the display scan parameter value Screen Change = ENABLE, each main
operation screen is showing on LCD screen during time defined by Change
Time parameter value.
Ifī theī displayī typeī parameterī valueī ī Screenī Typeī =ī SINGLE
Channelī Name
Processī Value
MAINī OPERATIONī (CHANNEL-4ī SCREEN)
Pressī number
F2ī orī F3
buttonsī for
accessingī the
relevantī channel
screen.
If the display scan parameter value Screen Change = ENABLE, each main
operation screen is showing on LCD screen during time defined by Change
Time(sec) parameter value
If more than one alarm messages is present, each alarm message is
showing on LCD screen during 1 second.
MAINī OPERATIONī SCREEN
OPERATORī PARAMETERS
PASSWORDī SCREEN
OPERATORī PARAMETERS
PASSWORDī INPUTī SCREEN
OPERATORī PARAMETERS
(CHANNEL-1)
OPERATORī PARAMETERS
(CHANNEL-1ī PARAMETERS)
Accessingī toī theī Technicianī Parameterī Pages
Operatorī Pagesī Parametersī Definetions
If no operation is performed for 20 seconds in operator parameters section,
device turns to main operation screen automatically.
If the device has a optional RS485 communication then RS 485 page is
observed, If the device has a optional USB communication then USB page is
observed.
If no operation is performed for 20 seconds in operator or technician
parameters section, device turns to main operation screen automatically.
If the device has a optional ETHERNET communication then ETHERNET
page is observed, otherwise this page is not observed.
MAINī OPERATIONī SCREEN
MENUī SCREEN
Whenī theī F1ī menuī buttonī isī pressed
whileī theī mainī screenī isī onī theī page,ī the
menuī pageī isī displayed.
DEVICEī SETTINGS
(DEFAULTī SETTINGS)
A
A
A
A A
A A
A A
A A
A A
A A
A A
AA
AA
A A
AA
AA
A A
A
Unitī Select
Type of unit value is adjusted according to this parameter for selected channel which is
shown on display.The value of parameter C, Bar, Ph, %, mm, m.
O
Hysteresis
Hysteresis parameter value for Alarm and Pre-Alarm is can be adjusted by this
parameter. It can be adjust between -400 0
O O
C to +40 C.
Band Alarm
Bandwith for Band alarm is can be adjusted by this parameter value.
It can be adjust between -400 0
O O
C to +40 C.
Sensor Alarm
Sensor break alarm for selected channel is can be disable or enable by this parameter.
It can be adjust between 0 to 1. Parameter values;
0 = DISABLE
1 = ENABLE
Offset
Process offset value for selected channel is can be adjusted by this parameter.
It can be adjust between -50.0 0
O O
C to +50. C.
Controlī Parameters-ī Otherī Parameters
Screen Type
Main operation screen type is adjusted by this parameter.
It can be adjust between 0 to 1. Parameter values;
0 = MULTIPLE
1 = SINGLE
Screen Change
It can be adjust between 0 to 1. Parameter values;
0 = DISABLE
1 = ENABLE
Display channel scanner mode is adjusted by this parameter.
Change Time(sec)
Display scan period is adjusted by this parameter. All main operation screen is
displayed during time defined by this parameter. It can be adjust between 1 to 3600
secs.
Baudrate
It can be adjust between 0 to 5. Parameter values;
0 = 4800 3 = 38400
1 = 9600 4 = 57600
2 = 19200 5 = 115200
Modbus communication baudrate for RS232 is can be adjusted by this parameter.
Parity
It can be adjust between 0 to 2. Parameter values;
0 = NONE
1 = ODD
2 = EVEN
Modbus communication parity bit for RS232 is can be adjusted by this parameter.
Stop Bit
It can be adjust between 1 to 2. Parameter values;
1 = 1 Stop bit
2 = 2 Stop bits
Modbus communication stop bit for RS232 is can be adjusted by this parameter.
Id
Modbus communication device ID for RS232 is can be adjusted by this parameter.
This parameter value is can be adjusted from 1 to 247.
File Name
USB file name for recording analogue values is can be adjusted by this parameter. File
name can be adjusted maximum 10 characters. Recording file on usb is csv formatā ā
and all data is seperated each other with tab. Example file format is explained below.
Label
When the analogue values are recorded on USB file, user can be defined label for this
recording. Label can be adjusted maximum 10 characters. Label are recorded at the
end of every lines of file.
Date Record
It can be adjust between 0 to 1. Parameter values;
0 = DISABLE
1 = ENABLE
When the analogue values are recorded on USB file, user can be save the recording
time on the file. Recording time is recorded at the beginning of every lines of file.
Record Time(sec)
It can be adjust between 0 to 3600 secs.
Record time interval is can be adjusted by this parameter. Analogue values are
recorded on USB file with this time interval. If
this parameter value is 0 usb recording is disabled.
Flash Memory āUSB Flash Memory Stick Detected Testā
Detection of the USB memory device being inserted is tested with this parameter.
When the USB memory device is plugged in, the message "OK" is displayed.
DHCP
It can be adjust between 0 to 1. Parameter Values;
0 = DHCP DISABLE
1 = DHCP ENABLE
DHCP is an automatic configuration protocol used on IP networks, If DHCP is enable,
device is adjust our ethernet communication configuration parameters (IP,
Netmask,Gateway) dynamicaly for your network system. If DHCP is disable, you must
adjust ethernet configuration parameters (IP, Netmask,Gateway) for your network
system.
Port No
Ethernet port number is can be adjusted by this parameter.
Netmask
Subnet mask for ethernet communication is can be adjusted by this parameter. If
DHCP is selected as a enable there is no need to adjust to this parameter, if DHCP is
selected as a disable then user must adjust this parameter according to the their own
network system.
Gateway
Gateway for ethernet communication is can be adjusted by this parameter. If DHCP is
selected as a enable there is no need to adjust to this parameter, if DHCP is selected as
a disable then user must adjust this parameter according to the their own network
system.
Ip No
IP address for ethernet communication is can be adjusted by this parameter. If DHCP
is selected as a enable there is no need to adjust to this parameter, if DHCP is selected
as a disable then user must adjust this parameter.
Channel Status
It can be adjust between 0 to 1. If parameter value
0 = DISABLE
1 = ENABLE
Channel is enabled and disabled by this parameter. If channel is selected as a disabled
this channel is can not be observed in main operation scren for single view mode,
channel alarm is not be controlled and analogue value for this channel is can not be
recording on USB file. ,
Channel Name ā āChannels label definition
All channels have their own label, is displayed in main operation screen. channel labels is can
be adjusted by this parameter. Channel labels are can be adjusted maximum 10 characters.
Alarm Type
Alarm type for selected channel is can be adjusted according to this parameter.
It can be adjust between 0 to 2. Parameter values;
0 = LOW 1 = HIGH 2 = BAND
PreAlarm Type
Pre-Alarm type for selected channel is can be adjusted according to this parameter.
It can be adjust between 0 to 2. Parameter values;
0 = LOW 1 = HIGH 2 = BAND
BackLightOnLevel
Display backlight is can be controlled by this parameter value. It can be adjust
between 50 to 100.
BackLightOffLevel
CO mode for backlight; in case off selection no backlight . ThisE parameter is can be
adjusted from 1 to 100.
BackLightOffTime
Time for the access to ecomomic backlight mode. This parameter is can be adjusted
from 10 to 300.
Deviceī Settingsī -ī RS-232ī Settings
Deviceī Settingsī -ī RS-485ī Settings
Baudrate
It can be adjust between 0 to 5. Parameter values;
0 = 4800
1 = 9600
2 = 19200
3 = 38400
4 = 57600
5 = 115200
Modbus communication baudrate for RS485 is can be adjusted by this parameter.
Parity
It can be adjust between 0 to 2. Parameter values;
0 = NONE
1 = ODD
2 = EVEN
Modbus communication parity bit for Rs485 is can be adjusted by this parameter.
Stop Bit
It can be adjust between 1 to 2. Parameter values;
1 = 1 Stop bit
2 = 2 Stop bits
Modbus communication stop bit for Rs485 is can be adjusted by this parameter.
Id
Modbus communication device ID for Rs485 is can be adjusted by this parameter.
This parameter value is can be adjusted from 1 to 247.
Deviceī Settingsī -ī USBī Settings
Deviceī Settingsī -ī ETHERNETī Settings
TcpIp Selection
It can be adjust between 0 to 1.
0 = Modbus RTU Over TCP/IP
1 = Modbus RTU TCP/IP
TCP/IP Protocol is can be adjusted by this parameter.
Deviceī Settingsī -Defaultī Settings
Thisī sectionī isī usedī toī returnī defaultī settingsī back.
Deviceī Settingsī -ī Dateī andī Timeī Settings
Date and Time for device is adjusted by this parameter.
Deviceī Settingsī -ī Passwordī Change
Technician Password for device is adjusted by this parameter.
Deviceī Settingsī -ī Softwareī Update
It allows you to update the device's software with a USB flash memory.
Logs
In this page, events logs are shown.
Languageī Selection
Inī thisī page,ī theī languageī isī selectedī forī theī device.
F4F1 F2 F3
F4F1 F2 F3
SET
HYS
BAND
=
=
=
Alarm or Pre-Alarm Set value
Hysteresis value forAlarm and Pre-Alarm output
Bandwidth for Band Alarm.
ON
OFF
Process Value
ON
OFF
Alarm
Output
Process Value
Alarm
Output
SET
HYS
SET
HYS
ON
OFF
Alarm
Output
Process Value
BandAlarm
LowAlarm
HighAlarm
Operationī Graphicsī of Alarmī andī Pre-Alarmī Types
i
Modbus Addresses
Outputī Status Addresses
Outputsī Status Addresses Unit
CH-1 ALARMī OUT Channel-1 Alarmī Outputī Status
Address
00001
-
CH-2 ALARMī OUT Channel-2 Alarmī Outputī Status 00002
-
CH-3 ALARMī OUT Channel-3 Alarmī Outputī Status 00003
-
CH-4 ALARMī OUT Channel-4 Alarmī Outputī Status 00004
-
CH-5 ALARMī OUT Channel-5 Alarmī Outputī Status 00005
-
CH-6 ALARMī OUT Channel-6 Alarmī Outputī Status 00006
-
CH-7 ALARMī OUT Channel-7 Alarmī Outputī Status 00007
-
CH-8 ALARMī OUT Channel-8 Alarmī Outputī Status 00008
-
GEN. ALR.ī OUT General Alarmī Outputī Status 00009
-
GEN.PRE.ALR.ī OUT Generalī Pre-alarmī Outputī Status 00010
-
Note-1: Outputs status are can be readed with modbus function-1 (read coils).
Device s response for modbus function-1 is always 2 byte data although the modbusā
function request less than 9 outputs port.
Processī Values Addresses
Processī Values Addresses Unit
CH-1ī P.ī VALUE Channel-1ī Processī Value
Address
30001
CH-2ī P.ī VALUE Channel-2ī Processī Value 30002
CH-3ī P.ī VALUE Channel-3ī Processī Value 30003
CH-4ī P.ī VALUE Channel-4ī Processī Value 30004
CH-5ī P.ī VALUE Channel-5ī Processī Value 30005
CH-6ī P.ī VALUE Channel-6ī Processī Value 30006
CH-7ī P.ī VALUE Channel-7ī Processī Value 30007
CH-8ī P.ī VALUE Channel-8ī Processī Value 30008
Note-2: Process values are can be readed with modbus function-4 (read input
register). Because of the process values are displayed on LCD screen with point, the
reading valuesī from modbus is 10 times than the real values.
Parametersī Modbus Addresses
Parameterī Values Addresses Unit
CH-1ī NAME Channel-1ī Name
Address
42000ī -ī 42004
CH-2ī NAME Channel-2ī Name 42005ī -ī 42009String 42005ī -ī 42009
CH-3ī NAME Channel-3ī Name 42010ī -ī 42014
CH-4ī NAME Channel-4ī Name 42015ī -ī 42019
CH-5ī NAME Channel-5ī Name 42020ī -ī 42024
CH-6ī NAME Channel-6ī Name 42025ī -ī 42029
CH-7ī NAME Channel-7ī Name 42030ī -ī 42034
CH-8ī NAME Channel-8ī Name 42035ī -ī 42039
String
String
String
String
String
String
String
FILEī NAME USBī Fileī Name 42040ī -ī 42044String
LABEL USBī Label 42045ī -ī 42049String
CH-1 ALARMī SET Channel-1 Alarmī Setī Value 42050
CH-1ī PRE A.ī SET Channel-1ī Prealarmī Setī Value 42051
CH-1ī HYSTERESIS Channel-1ī Hysteresisī Value 42052
CH-1ī BAND ALARM Channel-1ī Bandwithī Value 42053
CH-2 ALARMī SET Channel-2 Alarmī Setī Value 42054
CH-2ī PRE A.ī SET Channel-2ī Prealarmī Setī Value 42055
CH-2ī HYSTERESIS Channel-2ī Hysteresisī Value 42056
CH-2ī BAND ALARM Channel-2ī Bandwithī Value 42057
CH-3 ALARMī SET Channel-3 Alarmī Setī Value 42058
CH-3ī PRE A.ī SET Channel-3ī Prealarmī Setī Value 42059
CH-3ī HYSTERESIS Channel-3ī Hysteresisī Value 42060
CH-3ī BAND ALARM Channel-3ī Bandwithī Value 42061
CH-4 ALARMī SET Channel-4 Alarmī Setī Value 42062
CH-4ī PRE A.ī SET Channel-4ī Prealarmī Setī Value 42063
CH-4ī HYSTERESIS Channel-4ī Hysteresisī Value 42064
CH-4ī BAND ALARM Channel-4ī Bandwithī Value 42065
CH-5 ALARMī SET Channel-5 Alarmī Setī Value 42066
CH-5ī PRE A.ī SET Channel-5ī Prealarmī Setī Value 42067
CH-5ī HYSTERESIS Channel-5ī Hysteresisī Value 42068
CH-5ī BAND ALARM Channel-5ī Bandwithī Value 42069
CH-6 ALARMī SET Channel-6 Alarmī Setī Value 42070
CH-6ī PRE A.ī SET Channel-6ī Prealarmī Setī Value 42071
CH-6ī HYSTERESIS Channel-6ī Hysteresisī Value 42072
CH-6ī BAND ALARM Channel-6ī Bandwithī Value 42073
CH-7 ALARMī SET Channel-7 Alarmī Setī Value 42074
CH-7ī PRE A.ī SET Channel-7ī Prealarmī Setī Value 42075
CH-7ī HYSTERESIS Channel-7ī Hysteresisī Value 42076
CH-7ī BAND ALARM Channel-7ī Bandwithī Value 42077
*
(ī )
*
(ī )
*
(ī )
*
(ī )
*
(ī )
*
(ī )
*
(ī )
*
(ī )
*
(ī )
*
(ī )
*
(ī )
*
(ī )
*
(ī )
*
(ī )
*
(ī )
*
(ī )
*
(ī )
*
(ī )
*
(ī )
*
(ī )
*
(ī )
*
(ī )
*
(ī )
*
(ī )
*
(ī )
*
(ī )
*
(ī )
*
(ī )
SET(SET -ī (BAND/2)) (SET +ī (BAND/2))
HYS HYS
Technicianī Parameters
Technicianī Pagesī Parametersī Definetions
USB Recording File Example
2011-06-23-17:26:09ī ī ī ī ī ī 130.6ī ī ī ī 129.1ī ī ī ī 130.5ī ī ī ī 129.5ī ī ī ī 130.0ī ī ī ī 129.9ī ī ī ī 130.3ī ī ī ī 129.1ī ī ī ī SAMPLE
2011-06-23-17:26:10ī ī ī ī ī ī 130.6ī ī ī ī 129.1ī ī ī ī 130.5ī ī ī ī 129.5ī ī ī ī 130.0ī ī ī ī 129.9ī ī ī ī 130.3ī ī ī ī 129.1ī ī ī ī SAMPLE
2011-06-23-17:26:12ī ī ī ī ī ī 130.6ī ī ī ī 129.1ī ī ī ī 130.5ī ī ī ī 129.5ī ī ī ī 130.0ī ī ī ī 129.9ī ī ī ī 130.3ī ī ī ī 129.1ī ī ī ī SAMPLE
2011-06-23-17:26:13ī ī ī ī ī ī 130.6ī ī ī ī 129.1ī ī ī ī 130.5ī ī ī ī 129.5ī ī ī ī 130.0ī ī ī ī 129.9ī ī ī ī 130.3ī ī ī ī 129.1ī ī ī ī SAMPLE
Recording Time CH-1
Value
CH
Value
-2 CH
Value
-3 CH
Value
-4 CH
Value
-5 CH
Value
-6 CH
Value
-7 CH
Value
-8 Label
Calib. Low
Calibration Low value for selected channel can be adjusted according to this
parameter.
Calib. High
Calibration High value for selected channel can be adjusted according to this
parameter.
Sensor Type
Analogue input signal to be applied according to this parameter for selected channel
which is shown on Display.
0 = 4-20 mA 1 = 0-20 mA 2 = 0-10 V
A
A
OC/Ph/Bar
OC/Ph/Bar
OC/Ph/Bar
OC/Ph/Bar
OC/Ph/Bar
OC/Ph/Bar
OC/Ph/Bar
OC/Ph/Bar
OC/Ph/Bar
OC/Ph/Bar
OC/Ph/Bar
OC/Ph/Bar
OC/Ph/Bar
OC/Ph/Bar
OC/Ph/Bar
OC/Ph/Bar
OC/Ph/Bar
OC/Ph/Bar
OC/Ph/Bar
OC/Ph/Bar
OC/Ph/Bar
OC/Ph/Bar
OC/Ph/Bar
OC/Ph/Bar
OC/Ph/Bar
OC/Ph/Bar
OC/Ph/Bar
OC/Ph/Bar
OC/Ph/Bar
OC/Ph/Bar
OC/Ph/Bar
OC/Ph/Bar
OC/Ph/Bar
OC/Ph/Bar
OC/Ph/Bar
OC/Ph/Bar
Internal Recording
The device can record in memory. When a USB memory is inserted, the recordings are
transferred to the USB memory with the file name containing the current date and
time.(Exp: 2017-07-30-09-08-12-CHAN8.txt) icon and transaction status (%)
are displayed on the screen until the transfer is complete.
If you want to eject the USB memory during transfer or recording; Press the F4 button
for 5 seconds and the USB memory must be removed (within 5 seconds) before the
icon on the screen disappears. If the USB stick is not removed during this time, the
transfer will resume from where it left off.
The device can store up to (Record time x 2) daily memos in its memory.Not:
Produktspezifikationen
Marke: | Emko |
Kategorie: | Temperaturregler |
Modell: | CHANNEL8A-N |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Emko CHANNEL8A-N benƶtigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Temperaturregler Emko
31 August 2024
31 August 2024
31 August 2024
28 August 2024
28 August 2024
28 August 2024
28 August 2024
19 August 2024
15 August 2024
14 August 2024
Bedienungsanleitung Temperaturregler
- Temperaturregler Voltcraft
- Temperaturregler Techno Line
- Temperaturregler Technoline
- Temperaturregler Ventus
- Temperaturregler Cocraft
- Temperaturregler Honeywell
- Temperaturregler Kathrein
- Temperaturregler Inkbird
- Temperaturregler Dimplex
- Temperaturregler JUNG
- Temperaturregler Davis
- Temperaturregler Bulex
- Temperaturregler Fluke
- Temperaturregler Opticlimate
- Temperaturregler ACV
- Temperaturregler Wachendorff
- Temperaturregler Ygnis
- Temperaturregler AstralPool
- Temperaturregler Jumo
- Temperaturregler Ziehl
Neueste Bedienungsanleitung fĆ¼r -Kategorien-
2 Oktober 2024
30 September 2024
28 September 2024
21 September 2024
20 September 2024
19 September 2024
5 September 2024
28 August 2024
28 August 2024
28 August 2024