Emko ESM-3720 Bedienungsanleitung

Emko Temperaturregler ESM-3720

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Emko ESM-3720 (3 Seiten) in der Kategorie Temperaturregler. Dieser Bedienungsanleitung war für 13 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/3

2.2 Panel Cut-Out

2. General Description

2.1 Front View and Dimensions of ESM-3720Temperature Controller

Mounting Clamp

Panel Surface

(maximum thickness 15 mm / 0.59 inch)

Front Panel

IP65 protection

NEMA 4X

ESM-3720 77x35 DIN Size Temperature Controller

Instruction Manual. ENG ESM-3720 01 V03 11/17

- 4 Digits Display

- NTC Input or

PTC Input or

(Must be determined in order.)

- Adjustable temperature offset

- PID or

- Operation selection of compressor operates continuously,

stops or operates periodically in case of sensor defect

- Compressor protection delays

- Alarm parameters

- Adjustable internal buzzer according to sensor defect status.

- Password protection for programming section

- Installing parameters using Prokey

- Remote access, data collecting and controlling with Modbus RTU

- Having CE mark according to European Norms

J Type thermocouple Input or,

K Type thermocouple Input or,

2-Wire PT-100 Input or,

2-Wire PT-1000 Input

ON/OFF temperature control

- Selectable heating or cooling function

- Selection of operation with hysteresis

- Adjustable temperature offset

- Set value low limit and set value high limit boundaries

ESM- 20 77 x 35 DIN Size37

Digital Temperature Controller

Operating Temperature : -20 to 70 °C

Max. Operating Humidity : 90% Rh (non-condensing)

Altitude : Up to 2000 m.

Forbidden Conditions:

Corrosive atmosphere

Explosive atmosphere

Home applications (The unit is only for industrial applications)

1.2 General Specifications

1.Preface

ESM-3720 series temperature controllers are designed for measuring and controlling

temperature. They can be used in many applications with their On / Off control form, heating

and cooling control form and easy-use properties. Some application fields which they are

used are below:

Application Fields Applications

Glass Heating

Food Baking Ovens

Plastic Incubators

Petro-Chemistry Storages

Textile, Automative Air Conditioning

Machine Production Industries Etc... Etc...

1.1 Environmental Ratings

3 41615

13 14

A visual inspection of this product for possible damage occurred during shipment is

recommended before installation. It is your responsibility to ensure that qualified mechanical

and electrical technicians install this product.

If there is danger of serious accident resulting from a failure or defect in this unit, power off the

system and separate the electrical connection of the device from the system.

The unit is normally supplied without a power supply switch or a fuse. Use power switch and fuse

as required.

Be sure to use the rated power supply voltage to protect the unit against damage and to prevent

failure.

Keep the power off until all of the wiring is completed so that electric shock and trouble with the

unit can be prevented.

Never attempt to disassemble, modify or repair this unit. Tampering with the unit may results in

malfunction, electric shock or fire.

Do not use the unit in combustible or explosive gaseous atmospheres.

During putting equipment in hole on the metal panel while mechanical installation some metal

burrs can cause injury on hands, you must be careful.

Montage of the product on a system must be done with it’s fixing clamps. Do not do the montage

of the device with inappropriate fixing clamp. Be sure that device will not fall while doing the

montage.

It is your responsibility if this equipment is used in a manner not specified in this instruction

manual.

EMKO Elektronik warrants that the equipment delivered is free from defects in material and

workmanship. This warranty is provided for a period of two years. The warranty period starts

from the delivery date. This warranty is in force if duty and responsibilities which are determined

in warranty document and instruction manual performs by the customer completely.

Repairs should only be performed by trained and specialized personnel. Cut power to the

device before accessing internal parts.

Do not clean the case with hydrocarbon-based solvents (Petrol, Trichlorethylene etc.). Use of

these solvents can reduce the mechanical reliability of the device. Use a cloth dampened in

ethyl alcohol or water to clean the external plastic case.

1.3 Installation

1.4 Warranty

1.5 Maintenance

1.6 Manufacturer Company

Manufacturer Information:

Emko Elektronik Sanayi ve Ticaret A.Ş.

Demirtaş Organize Sanayi Bölgesi Karanfil Sk. No:6 16369 BURSA/TURKEY

Phone : +90 224 261 1900

Fax : +90 224 261 1912

Repair and maintenance service information:

Emko Elektronik Sanayi ve Ticaret A.Ş.

Demirtaş Organize Sanayi Bölgesi Karanfil Sk. No:6 16369 BURSA /TURKEY

Phone : +90 224 261 1900

Fax : +90 224 261 1912

6.5 Alarm Types

All order information of ESM-3720 Temperature Controller are given on the table at above. User may

form appropriate device configuration from information and codes that at the table and convert it to the

ordering codes.Firstly, supply voltage then other specifications must be determined. Please fill the order

code blanks according to your needs.

Please contact us, if your needs are out of the standards.

8.Ordering Information

Note-1:If input type is selected PTC or NTC (BC= 12, 18), Temperature sensor is given with the

device.For this reason, if input type is selected as PTC,sensor type (V = 0,1 or 2) or if input type is

selected as NTC, sensor type (V = 0,3 or 4) must be declared in ordering information.

ESM- 2037

V Þ Vac,

Z Þ Vdc

Þ Vdc or Vac can be appliedW

Power Supply

Input

Temperature Sensor

Input

76 mm / 3 inch

OC S P

6 mm / 0.24 inch

34,5 mm / 1.36 inch

65 mm / 2.56 inch

Maximum 15 mm / 0.59 inch

110 mm / 4.33 inch (min)

71 mm / 2.79 inch

29 mm / 1.14 inch

50 mm / 1.97 inch (min)

230V ( %15) 50/60HzV ±

Optional Supply Voltage

- 30 V Z

115 V ( %15) 50/60Hz,±

24 V ( %15) 50/60Hz,±

Standard

A BC D E FG HI /

U V W Z/

/0 1 0 0

1Relay Output (16(8) A@250 V ,at resistive Load, 1 NO )V

Control Output

Supply VoltageA

Input TypeBC Scale(°C)

ESM- 20 37

-50°C/-58°F ; 150°C/302°F

12 PTC (Not-1)

Temp. Sensor which is given with ESM- 20 37

0None

3NTC-M5L20.K1.5 (NTC Sensor, thermoplastic moulded with 1.5 m cable

for cooling application)

4NTC-M6L50.K1.5 (NTC Sensor, stainless steel housing with 1.5 m cable

for cooling application)

9 Customer

115V ( %15) 50/60Hz - 1.5VAV ±

5230V ( %15) 50/60Hz - 1.5VAV ±

0 01 0

810 - 30 V Z

-50°C/-58°F ; 100°C/212°F18 NTC (Not-1)

1PTC-M6L40.K1.5 (PTC Air Probe 1.5 mt Silicon Cable)

2PTCS-M6L30.K1.5.1/8” (PTC Liquid Probe 1.5 mt Silicon Cable)

(77x35 DIN Sizes)

Your Technology Partner

www.emkoelektronik.com.tr

Thank you very much for your preference to

use Emko Elektronik products, please visit our

web page to download detailed user manual.

9.Optional Accessories

RS-485 Communication

Interface

1.RS-485 Module 2.PROKEY Programming Module

The device is programmed(Upload or

Download) by using The parameters.

ESM3720

SET

0°C/32°F ; 800°C/1472°F05 J ,Fe CuNi IEC584.1(ITS90)

0°C/32°F ; 999°C/1830°F10 K ,NiCr Ni IEC584.1(ITS90)

-50°C/-58°F ; 400°C/752°F11 PT 100, IEC751(ITS90)

-19.9°C/-4°F ; 99.9°C/212°F09 PT 100, IEC751(ITS90

-50°C/-58°F ; 400°C/752°F14 PT 1000, IEC751(ITS90)

-19.9°C/-4°F ; 99.9°C/212°F13 PT 1000, IEC751(ITS90

324V ( %15) 50/60Hz - 1.5VAV ±

NTC, PTC,

J or K Type TC

2-Wire PT-100

2-Wire PT-1000

Output-1

Standard

Optional

(Relay Output)

(SSR Drive Output)

2SSR Driver Maximum 20m, Maximum 17V Output ( Z )

224V ( %15) 50/60Hz - 1.5VA ±W

01 Relay Output (5 A@250 V ,at resistive Load, 1 NO )V

Alarm Output

Control Output

Heating or Cooling

Function

PID or ON/OFF Operation

Alarm Output

Output-2

(Relay Output)

Device Type : Temperature Controller

Housing & Mounting : 76mm x 34.5mm x 71mm plastic housing for panel

Mounting. Panel cut-out is 71x29mm.

Protection Class : NEMA 4X (Ip65 at front, Ip20 at rear).

Weight : Approximately 0.20 Kg.

Environmental Ratings : Standard, indoor at an altitude of less than 2000 meters

with none condensing humidity.

o o o o

Storage / Operating Temperature : -30 C to +80 C / -20 C to +70 C

Storage / Operating Humidity : 90 % max. (None condensing)

Installation : Fixed installation

Overvoltage Category : II.

Pollution Degree : II, office or workplace, none conductive pollution

Operating Conditions : Continuous

Supply Voltage and Power :

: 115

: 24

:10 - 30

Temperature Sensor Input : NTC, PTC, TC, RTD

NTC input type : NTC (10 k @25 °C )W

PTC input type : PTC (1000 @25 °C )W

Thermocouple input type : J, K (IEC584.1) (ITS 90)

Thermoresistance input type : PT-100, PT-1000 (IEC751) (ITS 90)

Accuracy : ± 1 % of full scale for thermoresistance

Cold Junction Compensation : Automatically ± 0.1°C / ± 1°C

Sensor Break Protection : Upscale

Sampling Cycle : 3 samples per second

Control Form : PID or ON / OFF

Relay Output : A@250 V for Resistive load ( Output)16(8) V

(Electrical life : 100.000 switching at full load)

: 5 A@250 V for Resistive load (Alarm Output) V

Optional SSR Drive Output : Maximum 20mA, Maximum V

Display : 14 mm Red 4 digits LED Display

o o

LED : S (Green), P (Green), C (Yellow), F(Yellow),

Compressor Output (Red), Heating Output (Red)

Internal Buzzer : 83dB³

Approvals :

230V ( %15) 50/60Hz - 1.5VA

V ( %15) 50/60Hz - 1.5VA

V 1.5WZ

15 Z

V ±

W ±

Compressor

7. Specifications

Process High

Alarm

Output

Process Low

Alarm

Deviation High

Alarm

Deviation Low

Alarm

Deviation Band

Alarm

Deviation Range

Alarm

OFF

Alarm

Output

Process Value

OFF

Alarm

Output

Process Value

OFF

Alarm

Output

Process Value

( + )

OFF

Process Value

OFF

Alarm

Output

Process Value

OFF

Alarm

Output

Process Value

OFF

Alarm

Output

Process Value

Deviation Range

High Alarm

Process

Set

Alarm

Hysteresis

Alarm

Set

Alarm

Set

Alarm

Hysteresis

Process

Set

Alarm

Set

Alarm

Hysteresis

( - )

Process

Set

Alarm

Set

Process

Set

Alarm

Hysteresis

( - )

Process

Set

Alarm

Set ( + )

Process

Set

Alarm

Set

Alarm

Hysteresis

Alarm

Hysteresis

Process

Set

( - )

Process

Set

Alarm

Set ( + )

Process

Set

Alarm

Set

Alarm

Hysteresis

Alarm

Hysteresis

Process

Set

( - )

Process

Set

Alarm

Set

Alarm

Hysteresis

6. Changing and Saving Temperature Set Value

Main Operation Screen

When SET button pressed ‘’S’’ led will

be active and temperature set value will

be displayed.

SET Value Screen

Temperature set value can

be changed with increment

and decrement buttons.

When ENTER button pressed

temperature set value can be saved.

‘’S’’ will be inactive and goes back to

main operation screen.

Main Operation Screen

Temperature set value parameter (Default=50) MODBUS ADDRESS:40001

Temperature set value, can be programmed between minimum temperature set value and

maximum temperature set value .

OCPS

4.2 Device Label and Connection Diagram

4. Electrical Wiring Diagram

4.1 Supply Voltage Input Connection of the Device

Note-1 : External fuse is recommended.

Make sure that the power supply voltage is the same

indicated on the instrument.

Switch on the power supply only after that all the electrical

connections have been completed.

Supply voltage range must be determined in order. While

installing the unit, supply voltage range must be controlled

and appropriate supply voltage must be applied to the unit.

There is no power supply switch on the device. So a power

supply switch must be added to the supply voltage input.

Power switch must be two poled for seperating phase and

neutral, On/Off condition of power supply switch is very

important in electrical connection.

External fuse that on power supply inputs must be on V

phase connection.

External fuse that on Zpower supply inputs must be on (+)

connection.

230V CONNECTION DIAGRAMV

5.Front Panel Definition and Accessing to the Menus

BUTTON DEFINITIONS

1. Increment Button :

** It is used to increase the value in the Set screen and Programming mode.

2. Decrement, Silencing Buzzer and Downloading to Prokey Button :

** It is used to decrease the value in the Set screen and Programming mode.

** It is used to silence the buzzer.

** If Prc =0, it is used to download from device to prokey.

3. Set Button :

** In the main operation screen; if this button pressed, temperature set value will be displayed.

Value can be changed using increment and decrement buttons. When Enter button pressed,

value is saved and alarm set value is dislayed. Value can be changed using increment and

decrement buttons. When Enter button pressed, alarm set value is saved and returns back to

main operating screen.

** To access the programming screen; in the main operation screen, press this button for 5

seconds.

**In the main operation screen; press ENTER button for 3 seconds to start auto tune operation.,

4. Enter Button :

** It is used to saving value in the Set screen and programming screen.

LED DEFINITIONS

5. Cooling led :

** This led indicates that cooling control is selected and process output relay is active. If any

of compressor protection time active, this led blinks.

6.Heating led :

** This led indicates that heating control is selected and process output relay is active.

8.Celcius led :

** Indicates that device is in C mode.

9.Fahrenheit led :

** Indicates that device is in F mode.

10.Auto Tune led :

** Indicates that device is operating Auto Tune.

11.Set led :

** Indicates that device is in Set value changing mode.

12.Program led :

**Blinks in programming mode .

7.Alarm led :

** This led indicates that alarm output relay is active.

5 876 7

1110

Cooling

Heating

Sensor Offset Parameter ( Default = 0 ) MODBUS ADDRESS:40014

from -20 to 20 °C for NTC(-50°C, 100°C) or PTC(-50°C, 150°C) or J Type TC (0°C,800°C)

or J Type TC (0°C,1000°C) or PT-100(-50°C, 400°C)or PT-1000 (-50°C, 150°C) or

PT-100 (-20°C, 100°C),

from -36 to 36 °F for NTC(-58°F, 212°F) or PTC(-58°F, 302°F) or J Type TC (32°F,1472°F) or

or K Type TC (32°F,1830°F) or PT-100(-58°F, 752°F) or PT-1000(-58°F, 752°F) or

PT-100(-4°F, 212°F),

from -10.0 to 10.0°C for NTC(-50.0°C,100.0°C) or PTC(-50.0°C,150.0°C) or

PT-100 (-19.9°C,99.9°C),

from -18.0 to 18.0°F for NTC(-58.0°F,212.0°F) or PTC(-58.0°F,302.0°F) or

PT-100 (-4.0°F,212.0°F),

Compressor Start Delay at Power On Parameter ( Default = 0)

MODBUS ADDRESS:40015

When power is first applied to the device, compressor is on when this time delay is expired.

It can be adjusted from 0 to 20 minutes.

Compressor Stop-Start Delay Parameter ( Default = 0) MODBUS ADRES:40016

When compressor is inactive, this time delay must be expired for activation of the

compressor. It can be adjusted from 0 to 20 minutes.

Compressor Start-Start Delay Parameter ( Default = 0) MODBUS ADRES:40017

This time delay must be expired between two activation of the compressor. It can be

adjusted from 0 to 20 minutes.

MODBUS ADDRESS:30001 Temperature Value

MODBUS ADDRESS:30002 Empty

MODBUS ADDRESS:30003 Led Status : 0.bit C Led,

5.bit Heating Led,

6.bit Compressor Led,

13.bit Program Led,

14.bit Set Led

MODBUS ADDRESS:30004 Device Status :

0.bit Alarm Status

1.bit Buzzer Status

2.bit Sensor

MODBUS ADDRESS:30005 Output Status

0.bit Control Output

1.bit Alarm Output

MODBUS ADDRESS:30006 Device Type and Device Version

1.bit F Led,

3.bit Auto Tune Led,

7.bit Alarm Led,

Break Status

6.2 Modbus Adresses of Device Status Parameters (Read Input Register)

Operating Type Parameter ( Default = 0) MODBUS ADDRESS:40004

5 6 9 10

121187

1.Switch off the device.

2.Put in PROKEY then energize the device.

3.When the device is energized, the parameter values in PROKEY, start downloading to the device

automatically. At first, message is shown on the display, when loading has finished,

message is shown.

4.After 10 seconds device starts to operate with new parameter values.

5.Remove the PROKEY.

1-Before mounting the device in your panel,

make sure that the cut-out is of the right size.

2-Insert the device through the cut-out. If the

mounting clamps are on the unit, put out them

before inserting the unit to the panel.

3- Insert the mounting clamps to the fixing sockets

that located left and right sides of device and make

the unit completely immobile within the panel

1-Pull mounting clamps from left and right fixing

sockets.

2-Pull the unit through the front side of the panel

Before starting to remove the unit from

panel, power off the unit and the related

system.

2.3 Panel Mounting

2.4 Removing from the Panel

3. Using Prokey

DOWNLOADING FROM DEVICE TO PROKEY

1.The device is programmed by using the parameters.

2.Energize the device then put in PROKEY and press button. Message is shown on the

display. When the loading has finished, message is shown.

3.Press any button to turn back to main operation screen.

4.Remove the PROKEY.

DOWNLOADING FROM PROKEY TO DEVICE

NOTE: message is shown when an error occurs while programming. If you want to reload, put

in PROKEY and press button. If you want to quit, remove PROKEY and press button. The

device will turn back to main operation screen.

NOTE: message is shown when an error occurs while programming. If you want to reload,

switch off the device and put in PROKEY then energize the device. If you want to quit remove

PROKEY and press button. The device will turn back to main operation screen.

TO USE PROKEY, VALUE OF THE PrC PARAMETER MUST BE ‘0’.

IF PrC=1 AND BUTTON IS PRESSED MESSAGE WILL BE SHOWN. 10s. LATER

DEVICE TURNS BACK TO THE MAIN OPERATION SCREEN OR YOU CAN PRESS SET

BUTTON TO TURN BACK TO MAIN OPERATION SCREEN.

6.1 Programming Mode Parameter List

Hysteresis Parameter for Compressor Output ( Default = 3 )

MODBUS ADDRESS:40011

from 1 to 20°C for NTC (-50°C, 100°C) or PTC (-50°C, 150°C) or J Type TC ( 0°C, 800°C ) or

K Type TC ( 0°C, 1000°C or PT-100 Type ( -50°C,400°C ) or PT-1000 Type ( -50°C,400°C )

or PT-100 Type ( -20°C,100°C ),

from 1 to 36°F for NTC (-58°F, 212°F) or PTC (-58°F, 302°F) or J Type TC (32°F,1472°F)or

K Type TC (32°F,1830°F) or PT-100 Type (-58°F,752°F) or PT-1000 Type (-58°F,752°F)

or PT-100 Type (-4°F,212°F)

from 0.1 to 10.0°C for NTC(-50.0°C,100.0°C) or PTC (-50.0°C,150.0°C)

or PT-100 (-19.9°C,99.9°C),

from 0.1 to 18.0°F for NTC (-58.0°F,212.0°F) or PTC (-58.0°F,302.0°F) or

PT-100 (-4.0°F,212.0°F),

In ON/OFF control algorithm, temperature

value is tried to keep equal to set value by

opening or closing the last control element.

ON/OFF controlle d system, temperature

value oscillates continuously. Temperature

value’s oscillation period or amplitude around

set value changes according to controlled

system. For reducing oscillation period of

temperature value, a threshold zone is formed

below or around set value and this zone is

named hysteresis.

OFF

Temperature

Control

Output

Set

HSt

Time

HSt

Time

Minimum Temperature Set Value Parameter (Default = Minimum Value of Device

Scale ) MODBUS ADDRESS:40012

Temperature set value can not be lower than this value.

This parameter value can be adjusted from minimum value of device scale to maximum

temperature set value parameter

Maximum Temperature Set Value Parameter (Default = Maximum Value of Device

Scale ) MODBUS ADDRESS:40013

Temperature set value can not be bigger than this value.

This parameter value can be adjusted from minimum temperature set value parameter

to maximum value of the device scale

Decimal Seperator Enabling Parameter ( Default = 0 ) MODBUS ADDRESS:40003

Disable.

Enable.

Temperature Unit Selection Parameter ( Default = 0 ) MODBUS ADDRESS:40002

°C selected.

°F selected.

Sensor Defect Parameter ( Default = 0 ) MODBUS ADRES:40018

Compressor is active during this time period in case of probe defect (Default = 0)

MODBUS ADRES:40019

If probe defect parameter is 2, then this parameter is observed. It can be adjusted

from 0 to 99 minutes.

Compressor is OFF in case of sensor defect.

Compressor is ON in case of sensor defect.

Compressor operates periodically according to and Time periods in

case of sensor defect.

Compressor is inactive during this time period in case of probe defect

( Default = 0 )MODBUS ADRES:40020

If probe defect parameter is 2, then this parameter is observed. It can be adjusted

from 0 to 99 minutes.

Buzzer is active during this time

When this parameter is 1, if decrement button is pressed, is observed. In this

condition buzzer is active till buzzer silence button is pressed.

( Default = ) MODBUS ADDRESS:40030

If buzzer function selection parameter value =0, this parameter can not be

observed. Buzzer stays active during this time. It can be adjusted from 1 to 99 minutes

Programming Section Accessing Password

( Default = 0 ) MODBUS ADDRESS:40033

It is used for accessing to the programming section. It can be adjusted from 0 to 9999. If it is

selected 0, password will not be asked

PROKEY communication selected.

Communication Mode Selection Parameter ( Default = 0 ) MODBUS ADDRESS:40031

Rs485 communication selected.

Slave ID Parameter ( Default = 1 ) MODBUS ADDRESS=40032

Device communication address parameter (1 to 247).

OCPS

Power Supply Connection

EXTERNAL

FUSE

(1A T)

Note-1

Supply

Switch

Supply Voltage

5 6

Note: If sensor input type is selected J, K, PT-100 or PT-1000 (BC =05,10,11 or 14) parameter is

skipped.

230V ( %15) 50/60Hz ,

115V ( %15) 50/60Hz,

24V ( %15) 50/60Hz ,

V ±

W ±

10..30 V - 1.5 W

Must be determined in order.

Screen Blinking

Sensor failure . Sensor connection is wrong or there is no sensor connection. If buzzer function

selection parameter is 1, internal buzzer starts to operate.

When SET button is pressed for 5

seconds, “P” led starts to blink. If

programming mode entering

password is different from 0,

programming mode entering screen

will be observed.

Main Operation Screen

Programming Screen

Change the value with increment

and decrement buttons.

Hysteresis Value for

Compressor Output

Press SET button for accessing to the parameter

value. Press increment button for accessing to the

next parameter, press decrement button for

accessing to the previous parameter.

Press OK button for saving the

parameter.

Press increment button for accessing to the

next parameter, press decrement button for

accessing to the previous parameter

Password Entering Screen

Programming Mode

Entering Screen

Press OK button for

accessing to the

password entering

screen.

Password Entering Screen

Enter programming mode accessing password

with increment and decrement buttons.

Note2: If programming mode accessing password is 0, only three parameters

are accessible, and the parameter values can be changed.

Press OK button for entering

the password.

Note1: If programming

mode accessing

password is 0,

Temperature Unit screen

is observed instead of

programming screen

Hysteresis Value for

Compressor Output

If no operation is performed in programming mode for 20 seconds, device turns to main

operation screen automatically..

Hysteresis Parameter

for Compressor

6.4 Entering To The Programming Mode, Changing and Saving Parameter

CSPO

CSP

CSPO

CSP

6.3 Failure Messages in ESM-3720 Temperature Controller

CSPO

CSP

CPS O

CSP

, , , , and Parameters are observed if Operation type

is selected “Cooling”. If operation type is selected “Heating ” ,skip to the parameter.

ESM3720

SET

ESM3720

SET

ESM3720

SET

ESM3720

SET

üü

ESM3720

SET

ESM3720

SET

ESM3720

SET

ESM3720

SET

ESM3720

SET

ESM3720

SET

ESM3720

SET

ESM3720

SET

ESM3720

SET

(+)

(+)(-)

(-)

Relay or SSR Output

21 5 6 7 8

P/N : ESM-3720

Supply Voltage Input

Temperature Sensor Input

TC,NTC,PTC,PT-100

or PT-1000

230V ( %15) 50/60Hz

115V ( %15) 50/60Hz

24V ( %15) 50/60Hz

V ±

10...30 V

Must be determined in

(+)

(-)

For SSR Output

PROKEY

RS-485

7 8

L N

Pt10 0

5A SIGORTA

LOAD

SSR Driver Out

Max.

15V@30mA

HEAT

ALARM

5A@ 250V V

NOC

230 V ± 15% V

50/60Hz - 1.5VA

PROKEY

RS-485

PT-100

INPUT SCALE

(-19.9 ,99.9 ; °C °C °F °F-4 ,212 )

SSR Driver Out

Max.

15V@30mA

HEAT

ALARM

5A@ 250V V

NOC

P/N: ESM-3720 - 5.09.0.2/01.00/1.0.0.0

Note: If operating type is selected cooling and PID parameters are Device parameter

operates with On-Off control.

skipped.

Note: If this parameter is select 0, PID parameters will be not observed.If this parameter select 1,

Parameter will be not observed.

Temperature Control Selection Parameter On/Off or PID (Default = 0 )

MODBUS ADRES:40005

On - Off selected.

PID selected

Auto Tune Selection Parameter ( Default = 0 ) MODBUS ADRES:40006

Device does not do(Limit cycle Tuning) operation.

Device does operation

PID - Proportional Control Parameter ( Default = 5 ) MODBUS ADRES:40007

This parameter is entered as temperature.T

10 .

his parameter value is can be adjusted 0 to

% 0 of the device scale

PID-Integral Parameter( Default = 1000 ) MODBUS ADRES:40008

This parameter value can bu adjust from 0 to 3600.

PID-Derivativel Parameter ( Default = 250 ) MODBUS ADRES:40009

This parameter value can bu adjust from 0 to 3600.

PID-Period parameter( Default = 1 ) MODBUS ADRES:40010

This parameter value can bu adjust from 0 to 50

Temperature Minimum Alarm Parameter (Default =Minimum Value of Device Scale)

MODBUS ADRES:40024

If temperature alarm is active, this parameter value can be adjusted from minimum value

of device scale to temperature alarm set maximum parameter value .

Temperature Alarm Function Selection Parameter ( Default =1 )

MODBUS ADRES:40021

Alarm function is inactive.

Temperature Alarm Maximum Parameter ( Default = Maximum Value of Device Scale)

MODBUS ADRES:40025

If temperature alarm is active, this parameter value can be adjusted from temperature

alarm set value parameter to maximum value of the device scale.

Temperature Alarm On Delay Time Parameter(Default = 0)MODBUS ADDRESS:40026

Temperature alarm on delay time can be defined with this parameter.

It can be adjusted from 0 to 99 minutes.

Temperature Alarm Delay After Power On Parameter

When power is first applied to the device, this time delay must be expired for activation of

temperature alarm. It can be adjusted from 0 to 99 minutes.

( Default = 0 )

MODBUS ADRES:40028

Buzzer Function Selection Parameter ( Default = 0 ) MODBUS ADDRESS:40029

Buzzer is inactive.

Buzzer is active during sensor failures.

Buzzer is active if an alarm occurs.

Buzzer is active if an alarm occurs or sensor failures.

Process High alarm selected.

Process Low alarm selected.

Deviation High alarm selected.

Deviation Low alarm selected.

Deviation Band alarm selected.

Deviation Range alarm selected.

Deviation Range High alarm selected.

Temperature Alarm Parameter

This parameter value can be programmed between temperature minimum alarm set

parameter and temperature alarm set maximum parameter.

Set ( Default =80 )

MODBUS ADRES:40022

Temperature Alarm Parameter

This parameter value can be adjusted form 0.1 to %50 of the device scale if Pnt parameter is

1, 1 to %50 of the device scale if Pnt parameter is 0.

Hysteresis ( Default =3 )

MODBUS ADRES:40023

Temperature Alarm Off Delay Time Parameter(Default = 0)MODBUS ADDRESS:40027

Temperature alarm off delay time can be defined with this parameter.

It can be adjusted from 0 to 99 minutes. If it is higher than 99 is seen on the screen and

alarm latching output is selected. In

alarm latching output mode, in order to make passive

alarm output, press DECREMENT button at main screen.

Note: If this parameter is select 0, , , , , , and parameters

will be not observed

C F A

Produktspezifikationen

Marke:	Emko
Kategorie:	Temperaturregler
Modell:	ESM-3720

Brauchst du Hilfe?

Wenn Sie Hilfe mit Emko ESM-3720 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Temperaturregler Emko

Emko ESM-1520-N Bedienungsanleitung

31 August 2024

Emko ECO PID+ Bedienungsanleitung

31 August 2024

Emko Eco Lite Bedienungsanleitung

31 August 2024

Emko CHANNEL8A-N Bedienungsanleitung

28 August 2024

Emko ESM-3711-CN Bedienungsanleitung

28 August 2024

Emko ESM-4410 Bedienungsanleitung

28 August 2024

Emko ESM-4435 Bedienungsanleitung

28 August 2024

Emko ESM-3720 Bedienungsanleitung

19 August 2024

Emko ESM-4420 Bedienungsanleitung

15 August 2024

Emko ESM-3712-CN Bedienungsanleitung

14 August 2024

Bedienungsanleitung Temperaturregler

Neueste Bedienungsanleitung für -Kategorien-

JUNG TVA230NCWW Bedienungsanleitung

2 Oktober 2024

JUNG TRGO2 Bedienungsanleitung

30 September 2024

Technoline WS 9245 Bedienungsanleitung

28 September 2024

Voltcraft ETC-200 Bedienungsanleitung

21 September 2024

JUNG TRME2 Bedienungsanleitung

20 September 2024

JUNG TRCD241 Bedienungsanleitung

19 September 2024

Fluke 5606 Bedienungsanleitung

5 September 2024

JUNG TRDLS923048WW Bedienungsanleitung

28 August 2024

JUNG TRDLS923048 Bedienungsanleitung

28 August 2024

JUNG TRDA523048 Bedienungsanleitung

28 August 2024