Electro Harmonix Tone Tattoo Bedienungsanleitung


Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr Electro Harmonix Tone Tattoo (8 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war fĂĽr 8 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/8
1
TONE TATTOO
ANALOG MULTI-EFFECT PEDAL featuring
METAL MUFF, NEO CLONE & MEMORY TOY
Congratulations on your purchase of the fully analog Electro-Harmonix
TONE TATTOO, the first true multi-effect from Electro-Harmonix! The
TONE TATTOO combines three of the most popular guitar effects:
distortion, chorus and delay, into one small and convenient package.
Each section in the TONE TATTOO is taken directly from some of EHX’s
best selling effects: Metal Muff for distortion, Neo Clone for analog
chorus and alog delay from the Memory Toy. an
The effects in the TONE TATTOO are completely independent from each
other. Three separate footswitches, one for each section, allow for
individual control over which effect on or off. Each effect has its own is
dedicated kn s and switch all of which are tweakable at any moment; ob es
there are no menus to scroll through or dual function knobs.
The chain of effects in the TONE TATTOO is fixed as the following:
IN METAL MUFF NEO CLONE MEMORY TOY OUT→ → → →
Using the TONE TATTOO is like having three separate eects pedals on
your pedalboard but without the need for the additional cables or separate
power supplies and all in the footprint of one medium sized pedal. The
TONE TATTOO’s 5.75” x 4.75”. footprint is
WARNING: Your Tone Tattoo comes equipped with an Electro-Harmonix
9.6DC-200BI power supply (same as used by Boss® & Ibanez®: 9.6 Volts
DC 200mA). The Tone Tattoo requires mA at 9VDC with a center 75
negative plug. The Tone Tattoo does not take batteries. Using the wrong
adapter may damage your unit and void the warranty.
2
- CONTRO , INDICATORS & I/O - LS
METAL MUFF SECTION
DRIVE Knob –Controls the amount of input gain. As the DRIVE knob
is turned clockwise, the input gain of the Metal Muff increases and the
sound gets more distorted: getting crunchier, thicker and increasing in
saturation.
BASS Knob –Is an EQ control for the bass or low frequency response
of the Metal Muff. At its full clockwise position, the BASS knob provides
+18.5dB of boost at a center frequency of 105Hz. At its full counter-
clockwise position, this knob provides -18.5dB of attenuation at the same
center frequency of 105Hz. In the middle, center-detent position, the
bass frequencies are not altered.
TREBLE Knob –Is an EQ control for the treble or high frequency
response of the Metal Muff. At its full clockwise position, the TREBLE
knob provides up to +20dB of upper frequency boost starting at 700Hz.
At its full counter-clockwise position, this knob provides up to - dB of 20
upper frequency tenuation starting at the same 700Hz frequency. In at
the middle, center-detent position, the treble frequencies are not tered. al
SCOOP Switch – Provides two settings of attenuation in the middle
frequency range. T middle position of the SCOOP switch, labeled LO, he
provides low/medium amount of scoop, attenuating b -7.5dB, a y
centered at a frequency of 1.2kHz The upper position of the SCOOP .
switch, labeled HI, provides for a bigger scoop with an increased mid
frequency attenuation of -11dB centered at 1.2kHz. In the down
position, labeled OFF, there is no mid frequency attenuation.
GATE Button – When pushed down, the GATE button enables the gate
function of the METAL MUFF. When the GATE button is enabled, the
METAL MUFF LED is green. In the up position, the GATE button disables
the gate function and the METAL MUFF LED is RED.
Gate THRESHOLD Knob –Controls the input amplitude needed to
open the GATE. As you turn the THRESHOLD knob clockwise, the
amount of gating increases, requiring a louder signal to open the gate
and allow your instrument to pass through. Turning the THRESHOLD
knob down all the way is equivalent to disabling the GATE function.
Please see Page 4 for more information on how to use the gate function.
3
VOLUME Knob –Controls the overall output volume of the METAL
MUFF section of the TONE TATTOO.
NEO CLONE SECTION
RATE Knob –Controls the Neo Clone’s speed of modulation. As you
turn the RATE knob clockwise, the modulation speed of the chorus gets
faster. The speed of modulation varies from 0.4 Hz to 9 Hz.
DEPTH Button –Changes the intensity, or depth, of the chorus effect
choosing between high and low depth In the up position, the Neo Clone .
chorus is set to low depth giving a subtle chorus effect. The Neo Clone ,
LED lights up red in the lower depth position. When the button is pushed
in, the ch . Thorus’ depth is set to high for a more intense chorus effect e
Neo Clone LED lights up green when the button is pushed in.
MEMORY TOY SECTION
DELAY Knob –Controls the delay time of the Memory Toy section of
the Tone Tattoo. As you turn the DELAY knob clockwise, the delay time
increases. The range of delay time is 30mS to 550mS.
FEEDBACK Knob –Controls the number of echo repeats each note
produces. As you turn FEEDBACK clockwise, the number of repeats
increases. When you turn FEEDBACK all the way down, you will only
hear one echo for each note you play. If you turn FEEDBACK up to its
maximum clockwise position, the Memory
Toy’s echoes will “run away” build on top of each other for a - effect after
you play a note. A fairly high feedback setting with short delay settings
produces a reverb type of effect.
BLEND Knob –Allows you to vary the mix of the dry signal coming into
the Memory Toy section with the delayed signal produced within the
Memory Toy effect. BLEND varies from 100% dry, when set to full
counter-clockwise, to 100% wet at full clockwise.
GAIN Knob –Controls the input gain into the Memory Toy. As you turn
the GAIN knob clockwise the gain increases, making for a louder overall
effect. The GAIN knob increases the volume of both the dry and delayed
signal. Use the GAIN knob in conjunction with the BLEND knob to set the
Memory Toy to your preferred volume. Please Note: the delay signal will
saturate before the dry signal. The range of the GAIN knob is 0dB to
+23dB.


Produktspezifikationen

Marke: Electro Harmonix
Kategorie: Nicht kategorisiert
Modell: Tone Tattoo

Brauchst du Hilfe?

Wenn Sie Hilfe mit Electro Harmonix Tone Tattoo benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Electro Harmonix

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung fĂĽr -Kategorien-