Electro Harmonix String 9 Bedienungsanleitung


Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr Electro Harmonix String 9 (9 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war fĂĽr 11 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/9
WARNING: This device comes equipped with an Electro-Harmonix 9.6DC-200mA power
supply. It requires at 9VDC with a center negative plug. Use of the wrong adapter 100mA
or a plug with the wrong polarity may damage the device and void the warranty. Do not
exceed 10.5VDC on the power plug. Power supplies rated for less than 100mA will cause
the device to act unreliably.
Operating Instructions
Connect the supplied power adapter to the 9V power jack. Plug your instru-
ment into the INPUT jack. Connect your amp or mixer to the EFFECT OUTPUT
jack. Set the DRY knob to minimum (fully counterclockwise) and set the other
top row knobs to 12 o’clock. Select a preset (“SYMPHONIC” is a good starting
point) and step on the footswitch to turn on the LED. Play your instrument
and adjust controls to your liking.
For further inspiration, check out the STRING9’s Suggested Factory Settings
section. To download a blank User Settings PDF to record your favorite set-
tings, visit www.ehx.com/string9.
Congratulations on your purchase of the Electro-Harmonix STRING9 String
Ensemble. The STRING9 does for lush strings what the B9 does for organs, the
KEY9 does for electric pianos and the SYNTH9 does for analog synthesizers: now
anyone with an electric guitar can play great sounding lead string lines and
chordal string pads. The STRING9 is so amazing at producing atmospheric pads,
we took our groundbreaking Freeze algorithm from the HOG and Superego
and included it in three of the STRING9’s patches. Like our entire line of 9
series synthesizers, no special pickups are needed for clear polyphonic tracking
from single notes to full chords. Grab your favorite electric guitar and a
STRING9 and turn yourself into a string ensemble virtuoso.
1. DRY VOL Knob The DRY VOL knob controls the volume of the untreated
instrument signal present at the EFFECT OUTPUT jack. The DRY knob does not
control the volume of the DRY OUTPUT jack.
2. EFFECT VOL Knob The EFFECT VOL knob controls the overall volume of the
selected patch at the EFFECT OUTPUT jack.
3. CTRL 1 and CTRL 2 Knobs See the preset descriptions on page 4.
4. PATCH Knob Turn the white knob to select a strings patch.
5. BYPASS MUTE Internal DIP Switch Inside the STRING9 is a small DIP switch
labeled dry/mute. This switch allows you to choose the signal output from the
EFFECT jack when the STRING9 is in bypass mode.
While the STRING9 is in Bypass, and the DIP switch is set to (factory dry
default), the EFFECT jack outputs the signal present at the INPUT. This is the
standard guitar pedal routing for bypass. Set the DIP switch to mute, and
- 2 -
Controls and Connections
the EFFECT jack output is muted in bypass. This is handy when sending the
STRING9’s string effects to a different amplier or mixer channel and you
don’t want to hear your guitar out of that amp while in bypass.
To change the dry/mute DIP switch setting, do the following:
Remove the bottom cover of the STRING9.
Locate the small board with the footswitch and ribbon cable. Here you’ll
nd the DIP switch labeled dry mute and .
Change the dry/mute DIP switch setting with a small athead screwdriver.
Note: this switch is very delicate. Do not force it when changing settings.
If the switch handle doesn’t move easily, try moving it the other way rst
and then back to the position you want.
6. INPUT Jack Plug your instrument or the output of another effects pedal
into this ¼” jack. The input impedance at the INPUT jack is 1MΩ. See Tips 1 & 2
on page 7 of this manual for more information on connecting your STRING9.
7. DRY OUTPUT Jack The DRY OUTPUT jack outputs the signal present at the
INPUT jack through a buffer circuit. In either EFFECT or BYPASS mode, the dry
signal is always present at the DRY OUTPUT jack. The source impedance at the
DRY OUTPUT jack is 500Ω.
8. EFFECT OUTPUT Jack In effect mode, the EFFECT OUTPUT jack outputs the
mix set by the DRY and EFFECT volume knobs. In BYPASS mode, EFFECT out-
puts either the buffered bypass signal or is muted, depending on the setting
of the internal BYPASS MUTE DIP switch. The source impedance at the EFFECT
OUTPUT jack is 500Ω.
9. 9V Power Jack Attach the output plug from the included power supply to
the 9V power jack. The STRING9 draws 100mA at 9VDC on a center-negative
plug. Do not exceed 10.5VDC on the power jack.
10. BYPASS Footswitch and STATUS LED Press the Bypass footswitch to toggle
the EFFECT OUTPUT jack between buffered bypass/mute and EFFECT mode.
The status LED lights when you are in EFFECT mode. Change between buffered
bypass or mute—while in Bypass mode—by ipping the internal BYPASS MUTE
DIP switch. The STATUS LED blinks when waiting for a Freeze trigger or upon
receiving a new Freeze trigger.
Manual Freeze On The Bypass Footswitch
The Bypass footswitch performs double-duty, in addition to toggling between
bypass and effect modes, the footswitch also engages Manual Freeze when
the STRING9 is set to any of the last three patches: ORCH FREEZE, SYNTH
FREEZE, VOX FREEZE and the CTRL 2 knob is set to the CW half of its range.
- 3 -


Produktspezifikationen

Marke: Electro Harmonix
Kategorie: Nicht kategorisiert
Modell: String 9

Brauchst du Hilfe?

Wenn Sie Hilfe mit Electro Harmonix String 9 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Electro Harmonix

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung fĂĽr -Kategorien-