Electro Harmonix Stereo Pulsar Bedienungsanleitung


Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr Electro Harmonix Stereo Pulsar (2 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war fĂĽr 6 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/2
Congratulations on your purchase of the Stereo Pulsar, a variable
shape tremolo and panner pedal.
Connected as a mono pedal, the Stereo Pulsar is exactly the same
as the Electro-Harmonix Pulsar that we currently manufactur: a
tremolo pedal that allows significant control over the shape of
modulating waveform. Hook up the Stereo Pulsar in stereo (each
output to a separate amp/mixer channel) and you have a panner
pedal that will send your instrument back and forth between two
amps with the same control over waveform shape. So while one
amp is fading up in volume, the other will be fading down in volume
or even more dramatic: while one amp is on, the other is off.
— — CONTROLS
SHAPE Switch Selects between Triangle Wave and Square Wave Modes. –
SHAPE Knob – Changes the shape of the waveform that modulates the Tremolo.
Triangle Wave Mode – In this mode the LFO creates a Triangle Wave
oscillation, resulting in a smooth modulation. As the SHAPE knob is turned
from the Counter-Clockwise (minimum) position to the Center (middle)
position, the waveform starts as a rising Sawtooth changing into a Triangle.
From the Center position to the Clockwise (maximum) position, the wave
changes from a Triangle to a falling Sawtooth.
Square Wave Mode – In this mode, the LFO creates a Square Wave,
resulting in a sharp, on/off modulation. As the SHAPE knob is turned from
the Counter-Clockwise (minimum) position to the Center (middle) position,
the wave starts as a Small Pulse Width Wave changing into a Square Wave.
From the Center position to the Clockwise (maximum) position, the wave
changes from a Square Wave to a Large Pulse Width Wave.
DEPTH Knob – Adjusts the amount of Tremolo that will be applied to your signal.
As the DEPTH knob is turned from the Counter-Clockwise (minimum) position to
the Clockwise (maximum) position, the amount of the effect will increase. Maximum
tremolo occurs when the DEPTH knob is set to approximately 2 o’clock. As the
DEPTH knob is turned above 2 o’clock, the tremolo begins to warp by modulating
between positive and negative phase with a rhythmic pattern. To obtain maximum
pan when using the Stereo Pulsar in stereo, the optimum setting for the DEPTH knob
is at approximately 2 o’clock.
RATE Knob – Adjusts the speed of the tremolo or pan effect. As the RATE knob is
turned from the Counter-Clockwise (minimum) position to the Clockwise
(maximum) position, the modulation rate increases.
RATE/STATUS LED If the effect is engaged, the LED will blink at the same rate –
that the effect modulates. In bypass mode, the LED is off. The footswitch
engages/disengages the effect.
INPUT Jack – Connect your instrument’s output to this ¼” mono jack. The input
impedance presented at this jack is 1 Mohm. Plugging a cable into the INPUT jack,
when running the Stereo Pulsar off of a 9V battery, turns the Stereo Pulsar on and
drains the battery.
MAIN OUT Jack –Connect this ¼” mono jack to your amplifier’s input. The
output impedance presented at this jack is 1 kohm. When using the Stereo Pulsar as a
mono device we recommend you use the MAIN OUT jack so that the parameter
labels of the SHAPE knob correspond to what your hear.
STEREO OUT Jack – Connect this ¼” mono jack to your second amplifier’s input.
The output impedance presented at this jack is 1 kohm. When using the Stereo Pulsar
as a stereo device use the STEREO OUT jack for your second channel. You can
connect only the STEREO OUT jack if you want; the tremolo effect will be the same
as from the MAIN OUT jack but the SHAPE knob labels will be reversed. For
example, when the SHAPE knob is set to its clockwise position, the tremolo will
have a falling sawtooth modulating it.
9V Power Jack –The Stereo Pulsar can run off of a 9V battery or you can connect a
9VDC battery eliminator capable of delivering at least 100mA to the 9V power jack.
The optional 9V power supply from Electro-Harmonix is (same as US9.6DC-200BI
used by Boss & Ibanez The battery eliminator must ™ ™) 9.6 volts/DC 200mA.
have a barrel connector with center negative. The battery may be left in or taken out
when using an eliminator.
- POWER -
Power from the internal 9-volt battery is activated by plugging into the INPUT jack. The input
cable should be removed when the unit is not in use to avoid running down the battery. If a
battery eliminator is used, the Stereo Pulsar will be powered as long as a wall-wart is
plugged into the wall.
To change the 9-volt battery, you must remove the 4 screws on the bottom of the Stereo
Pulsar. Once the screws are removed, you can take off the bottom plate and change the
battery. Please do not touch the circuit board while the bottom plate is off or you risk
damaging a component.


Produktspezifikationen

Marke: Electro Harmonix
Kategorie: Nicht kategorisiert
Modell: Stereo Pulsar

Brauchst du Hilfe?

Wenn Sie Hilfe mit Electro Harmonix Stereo Pulsar benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Electro Harmonix

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung fĂĽr -Kategorien-