Elba ETM-E3690P Bedienungsanleitung
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Elba ETM-E3690P (1 Seiten) in der Kategorie Kraan. Dieser Bedienungsanleitung war für 5 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/1
ETM-E3690P
1. An opening hole of 35mm diameter is required on sink top or work top (C) for installation of tap.
2. Slide the rubber O-ring (B) up to the base of tap (A).
3.Screw the flex hoses (H) up to the extension tube, then insert the tap through the hole of sink top or
worktop (C), and position the tap properly.
4.Slide the plastic fitting I (D) through the extension tube ,then slide the plastic fitting II (E) through the
sprayer hose and up to the plastic fitting I(D).
Important: ensure the opening of plastic fitting I (D) is close to threaded tube , and the sprayer hose
runs freely through the plastic fitting II (E).
5.Put the permanent seat(F) through the threaded tube , and tighten the fixing washer(G) securely.
Important: make sure the hose runs smoothly before tightened the fixing washer.
6.Connect the flex hoses (H) to the hot & cold water supply, and the sprayer hose to the threaded tube.
7. Adjusting the pull-out length of sprayer hose and fasten the weighing ball (I) with screws.
●Before installation, please ensure that the following
work conditions are adhered to:
-Water temperature between 0 C - 90 C˚ ˚
-Water pressure between 0.05MPa – 1.0MPa. Pressure
reducing valve is necessary if pressure exceeds 1.2MPa
-Avoid major pressure di erences between hot and cold ff
water supply
●Flush pipes thoroughly before and after installation to
ensure water supply is free of any debris.
●Inspect tap fitting and debugged to its best. Do not
attempt to disassemble fitting on your own.
●Use thread sealant tape (PTFE) on any screw joining
connections and ensure all joints are securely tightened.
A Tap body
B Rubber O ring
C Sink top or work
top
D Plastic fitting I
E Plastic fitting Ⅱ
F Permanent seat
G Fix ing washer
H Flex hose
I Weighing ball
J Rubber washer
for flexi hose
This . FIAMMA SDN. BHD. will not be held responsible for the use of superseded or voided specifications.
Fabricatoe must check for cut-out accuracy.
specification is subject to change without notice
Stainless Steel Mixer Tap
Produktspezifikationen
| Marke: | Elba |
| Kategorie: | Kraan |
| Modell: | ETM-E3690P |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Elba ETM-E3690P benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Kraan Elba
6 September 2024
6 September 2024
6 September 2024
6 September 2024
6 September 2024
Bedienungsanleitung Kraan
- Kraan Ernesto
- Kraan Teka
- Kraan IKEA
- Kraan Inventum
- Kraan Smeg
- Kraan Lynx
- Kraan Caple
- Kraan Livarno
- Kraan Franke
- Kraan Nodor
- Kraan Miomare
- Kraan Grohe
- Kraan Delta
- Kraan Hansgrohe
- Kraan Brita
- Kraan Schütte
- Kraan Lamona
- Kraan CDA
- Kraan Quooker
- Kraan BLANCO
- Kraan Elkay
- Kraan Deante
- Kraan Neo
- Kraan Everpure
- Kraan ZLine
- Kraan Sani-Lav
- Kraan Fala
- Kraan Omnires
- Kraan CurAqua
- Kraan Gessi
- Kraan Sussex
- Kraan Fantini
- Kraan Oliveri
- Kraan Zip
- Kraan Moen
- Kraan WillieJan
- Kraan Lomazoo
- Kraan Billi
- Kraan SaniSupreme
- Kraan Viidako
- Kraan Waltec
- Kraan Graff
Neueste Bedienungsanleitung für -Kategorien-
18 September 2024
15 September 2024
15 September 2024
15 September 2024
15 September 2024
15 September 2024
14 September 2024
13 September 2024
13 September 2024
12 September 2024