Draper Silhouette/Series M Bedienungsanleitung
Draper
Projektionsfläche
Silhouette/Series M
Lesen Sie kostenlos die đ deutsche Bedienungsanleitung fĂźr Draper Silhouette/Series M (2 Seiten) in der Kategorie Projektionsfläche. Dieser Bedienungsanleitung war fĂźr 10 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/2
Your Draper screen can be mounted on a wall or suspended from the ceil ing,
or mounted on special 6" extension bracket. Extension brackets must be
ordered separately from Draper. With each method of installation, the case
must be mounted level and with the ďŹ at back parallel to the wall.
To reduce the risk of personal injury, use only the hardware which comes
with the screen or is speciďŹ ed in these instructions.
The screen (or extension brackets) should be mounted into studs or block ing
in the wall/ceiling, or in drywall (minimum thickness
1/2") with speciďŹ ed anchors.
For any other type of installation, follow all local build ing and safety codes.
Steel studs, concrete or cinder block walls and all other types of non-wood
frame construction require the use of special screws or anchors. The se-
lec tion of ap pro pri ate mounting hardware should be made by a qualiďŹ ed
pro fes sion al installer.
When locating viewing surface and checking clearance for screenâs op er a tion,
remember surface is centered in case. Handle case carefully to avoid scratch-
ing. Regardless of mounting method, screen should be positively and securely
supported so that vibration or even abusive pulling on the viewing surface
will not cause case to work loose or fall. Installer must insure that fasteners
used are of adequate strength and suitable for the mounting surface.
Wall Mounting
Mount 2, 3, or 4 aluminum brackets provided (âZâ Clips) on the wall at
desired height, using appropriate fasteners. Verify that they are in line and
level to fully engage with the mounting lip on back of screen case. 1
5/8" of
free space is required above the âZâ Clips to allow case lip to be engaged
over the lip of the âZâ Clips.
Engage the lip on back of screen case with lip of âZâ Clip and gently pull
down to fully engage case to brackets.
Ceiling/Suspended Mounting
Locate two offset ceiling brackets (supplied) and slide these into the chan-
nel on top of screen case by aligning the chamfered edges of each bracket
parallel to the channel length. Allow bracket to drop against bottom of
channel and then rotate bracket counter-clockwise. Slide one bracket to
each end of screen case until it stops against end cap of case. Tighten two
set screws to lock bracket in place. Make sure that the ďŹ ange of the ceiling
bracket that has four holes is extended beyond the end caps of the case.
Repeat above procedure for second ceiling bracket, making sure to slide it
towards opposite end of case.
To mount against ceiling, hold screen case against ceiling and mark
mounting hole locations. Each brack et has 2 holes towards the front edge
and 2 holes towards the back edge. Installer must use at least 2 fasteners
per bracket with one fastener in one of the two holes clos est to back edge
of bracket, and one fas ten er in one of the two holes closest to front edge of
bracket. Installer must insure that fasteners are of adequate strength and
suitable for the mounting surface chosen.
To mount suspended from ceiling, the brackets need to be installed on
screen case as noted above. Attach âSâ Hooks (supplied) through the holes
in the brackets. Select the set of holes that allows the screen to hang in a
vertical position. The installer is to provide the materials and fasteners to
attach the âSâ Hooks to the ceiling. Installer must insure that the fasteners
and suspension material are of adequate strength and suitable for the
mounting surface chosen.
Ceiling racket in b
channel of case
Ceiling racketb
Mo nting fastenersu
(s pplied y others, 2 per racket)u b b
(front of Silho ette case)u
(right end of Silho ette case)u
Installation/Operating Instructions
Silhouette/Series M and C
Manually Operated Projection Screens by Draper
Lip on back
of case
"Z" Clip
(wall mounting bracket
supplied with Silhouette)
Silho ette f lly engaged u u
on "Z" Clip
Copyright Š 2012 Draper Inc. Form SilhouetteM&C_Inst12 Printed in U.S.A.
Caution
â
Read instructions through completely before proceeding; keep
them for future reference. Follow instructions carefully. Installation
con trary to instructions invalidates warranty. Care in both mount-
ing and correct operation willl assure long and sat is fac to ry service
from your Draper screen.
â
Screen should be accessible for complete removal should fabric
become damaged or for service if required.
â
Screen should be installed level (using a carpenterâs level).
â
Nothing should be fastened to screen dowel or viewing surface.
â
Operating crank for Series C is packed separately in screen car-
ton. Do not discard with packing material.
Note: Screen has been thoroughly inspected and tested at fac-
tory and found to be operating properly prior to shipment.
Installation
ÂŽ
If you encounter any difďŹ culties installing or servicing your
screen, call your dealer or Draper, Inc., Spiceland, Indiana, (765)
987-7999, or fax (765) 987-7142.
Extension Wall Brackets
6" or 10"-14" Extension Wall Brackets are needed to mount Silhouette
ex tend ed from wall. Wall Brackets are not supplied with screen and must be
ordered separately. Specify âSilhouette Extension Wall Bracketsâ.
â Mount the Wall Brackets to the wall, making sure they are level and verti-
cally plumb. Installer must insure fasteners (not included) are of adequate
strength and suitable for chosen mounting surface.
⥠Attach hanging bracket to wall bracket as shown.
⢠Attach (1) âZâ Clip and (1) Support Plate (supplied with screen) to hanging
bracket as shown.
⣠Engage the lip on back of screen case with lip of âZâ Clip and gently pull
down to fully engage case to brackets.
⤠Install hook bracket as shown making sure the two tabs of this bracket
hook over the case extrusion.
⼠Install #10-24 hex head screw through hook bracket, hanging bracket, and
support plate as shown.
Operating InstructionsâSeries M Standard
To lower picture sur face, pull screen down to de sired position. Hes i tateâthen
allow screen to slightly retract very slowly until it locks in place.
To raise picture surface, pull down on the pull bail, then raise quickly, as a window
shade. Keep control of the picture sur face. Do not allow it to roll un con trolled
into the case, or dam age is sure to result.
Operating InstructionsâSeries M with AutoReturn
To lower picture surface, pull screen down. âthen allow screen to Hesitate
retract very slowly until it locks in place.
To raise picture surface, pull screen down gently until it stops, then release.
Operating Instructionsâ Series C
To lower screen sur face, attach the crank handle to the âUâ joint stud located on
the left hand side of the screen. With the crank handle in its operating position,
rotate coun ter clock wise. An internal pin within the gear box will stop the screen
when fully extended. The crank handle can be removed if desired. The shipping
support brackets must be removed from each end of dowel during initial operation.
To raise screen surface, attach the crank handle to the âUâ joint stud located on
the left hand side of the screen. With the crank handle in its operating position,
rotate in a clockwise direction. An internal pin within the roller will stop the screen
when fully retracted. The crank handle can be removed if desired.
Removing Case Fascia
Caution: When removing or reattaching fascia, do not handle fascia by
unpainted ends.
Case fascia is removable to access roller assembly. To remove fascia, depress
outward the spring lip located inside lower front corner of screen case and pull
lower corner of fascia outward. Repeat this at right end of case. Support fascia
from center and rotate lower front edge upward ap prox i mate ly 40° to disengage
the Roll-Lok hinge at the top front of screen case. Fascia can now be completely
removed from case.
To install fascia, generally reverse instructions above making sure the Roll-Lok
hinge is completely engaged before rotating fascia down towards the closed
position. Depress spring clips outward, push lower corners of fascia inward until
lips of spring clips hook behind fascia.
Please Note: Be sure the clips are completely up against the ends of the
fascia.
Silhouette/Series M and Series C by Draper
Page 2 of 2
1½" Viewing Surface
23/ "8
21/ "8
4ž"
6"
Case Dimensions
Silhouette/Series M
Silhouette/Series C
Tab-Tension Adjustment Procedure for Silhouette/Series C
â Determine which side requires adjustment.
â Secure dowel with one hand.
Caution: Do not touch or bend surface.
â Using Philips-head screwdriver,
depress spring-loaded adjustment
screw (see drawing) and slowly turn
clockwise to tighten tension, or
counterclockwise to loosen tension.
The screw adjusts in Âź turn
increments. Adjust only
(Âź turn).one increment
â If problem is not corrected, leave
screen in position for 24 hours to allow
surface material to stretch into position.
â If problem still is not corrected, repeat steps
â
and
â
.
Do elwAdj stmentu
Screw
Tensioning
Ca leb
www.draperinc.com (765) 987-799
9
3"
Viewing Surface
Silhouette/Series M with Auto Return
Hook
Bracket
CB Ÿ"-20 x 1ž" Z Keg,
Flat Washer,
Âź"-20 Nylock Nut
#10-24 x 7/8"
Phillips Pan Head
Screw, Nylock Nut
#10-24 x ½"
Hex Head Screw
Z Clip
Wall
Bracket
Support
Plate
Hanging
Bracket
Produktspezifikationen
| Marke: | Draper |
| Kategorie: | Projektionsfläche |
| Modell: | Silhouette/Series M |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Draper Silhouette/Series M benĂśtigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Projektionsfläche Draper
7 September 2024
5 September 2024
3 August 2024
2 August 2024
2 August 2024
2 August 2024
1 August 2024
31 Juli 2024
31 Juli 2024
29 Juli 2024
Bedienungsanleitung Projektionsfläche
- Projektionsfläche Da-Lite
- Projektionsfläche Pyle
- Projektionsfläche Optoma
- Projektionsfläche Kodak
- Projektionsfläche NEC
- Projektionsfläche Celexon
- Projektionsfläche Elite
- Projektionsfläche AV:link
- Projektionsfläche Oregon Scientific
- Projektionsfläche Duronic
- Projektionsfläche GPX
- Projektionsfläche Luxburg
- Projektionsfläche EluneVision
- Projektionsfläche Stewart
- Projektionsfläche Elite Screens
- Projektionsfläche Lumene
- Projektionsfläche Avers
- Projektionsfläche Elite ProAV
- Projektionsfläche KHOMO GEAR
- Projektionsfläche EPV
Neueste Bedienungsanleitung fĂźr -Kategorien-
12 Oktober 2024
2 Oktober 2024
29 September 2024
27 September 2024
20 September 2024
11 September 2024
6 September 2024
6 September 2024
5 September 2024
4 September 2024