Draper Signature E Bedienungsanleitung
Draper
Projektionsfläche
Signature E
Lesen Sie kostenlos die đ deutsche Bedienungsanleitung fĂźr Draper Signature E (3 Seiten) in der Kategorie Projektionsfläche. Dieser Bedienungsanleitung war fĂźr 24 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/3
Limit Adjustments
Please Note: Screen limits are factory set for optimum performance of the
screen. A procedure is outlined below for minor tweaks, but any adjustment
of these limits may negatively affect the ďŹatness of the screen surface and
could also void the warranty. Please check with Draper prior to resetting
screen limits.
CAUTION: Always be prepared to shut screen off manually when new
adjustment is being tested. Screen may be severely damaged if viewing
surface is allowed to run too far up or too far down.
CAUTION: Be sure all switches are in âoffâ position before adjusting limit
switches.
The motor limit screws are normally located on the audience left of screen roller.
"Down" Limit Adjustment
To Reduce Screen Drop
1 Raise screen surface about 1' above desired setting and turn off.
2 Turn the WHITE/DOWN limit screw clockwise (3 screw turns=½ roller revolution).
3 Test by running screen down and repeat steps 1 and 2 until desired position is
reached.
To Increase Screen Drop
1 Run screen to the down limit.
2 With the down switch on, turn the WHITE/DOWN limit screw counterclockwise
(three turns of screw = ½ roller revolution) to increase drop.
3 Test by running screen up about 1' and back down to new down limit.
4 Repeat steps 2 and 3 until desired position is reached.
"Up" Limit Adjustment
Screen is Running Too Far Up
1 Lower screen surface about 1' below desired setting and turn off.
2 Turn the YELLOW/UP limit screw clockwise (3 screw turns = ½ roller revolution).
3 Test by running screen up.
4 Repeat steps 1 through 3 until desired position is reached.
Screen Needs to Run Up More
1 Run screen down about 1' and turn off.
2 With the up switch on, turn the YELLOW/UP limit screw counterclockwise (three
turns of screw = ½ roller revolution).
3 Repeat steps 1 and 2 until desired position is reached.
CAUTION: Do NOT allow the dowel to wrap up over the roller when the
screen is running up! This could damage the screen.
Installation/Operating Instructions
Signature/Series E & V Electric Projection Screen by Draper
Operation
Please Note: Screen limits are factory set for optimum performance of the screen.
Any adjustment of these limits could void the warranty. Please check with Draper
prior to resetting screen limits.
CAUTIONâImportant InstructionsâSignature/Series VâThe shipping support
bracket must be removed from the dowel during initial operation before screen is
operated in UP direction. After screen is installed, run viewing surface DOWN to access
and remove bracket. Signature/Series EâThe protective paper wrapping around the
viewing surface must be removed before the screen is operated in down direction. Cycle
viewing surface down and up several times to conďŹrm satisfactory operation. If viewing
surface or trap door do not operate properly, turn power off and free trap door and/or
check electrical connections.
When screen is ďŹrst operated, If automatic trap door does not open be cautious!
immediately up into screen case when switch is ďŹipped âdownâ, return switch to âoffâ and
free trap door and/or recheck electrical connections before proceeding. Cycle unit down
and up several times to conďŹrm satisfactory operation.
110-120V Single Station Controlâ3-position UP-OFF-DOWN switch permits
operation to be stopped at any point. Factory adjusted limit switches automatically stop
screen when fully down or fully up.
110-120V Multiple Station ControlâSwitches are similar in appearance to 110-120V
Single Station Control. Screen stops when switch is released and may be restarted in
either direction. Factory adjusted limit switches stop screen automatically when fully
down or fully up.
24V ControlâThree-button UP-STOP-DOWN switches stop at any point desired,
operate in any sequence. Factory adjusted limit switches automatically stop screen
when fully down or fully up. Wireless controlsâwhether infrared or radio frequencyâ
interface with the low voltage control box (see wiring diagram on reverse).
Key Operated SwitchingâTwo kinds of key-operated switches are optionally available
with this unit. The key-operated power supply switch controls power to the screen 1
and switches. When it is âoffâ, the switches will not operate screen. Key may be removed
from the switch in either âonâ or âoffâ position. A three-position key switch permits the 2
screen to be operated directly by key. In this case, the screenâs operator must always
have a key.
RS232/EthernetâSerial communication and network communication optionally
available with wall switches, RF or IR remote.
Hanging Screen
When locating viewing surface and checking clearance for screenâs operation,
remember surface is centered in case. Screen is normally recessed above ceiling
and may be installed in a variety of ways. See typical installations detailed on back
of this sheet. Regardless of mounting method used, the following points apply:
1 Screen should be lifted into position only by the end mounting brackets.
Keep case level by lifting end plates simultaneously to prevent surface
damage. Never attempt to lift screen along its length.
2 Screen should be positively and securely supported so that vibration or even
abusive pulling on viewing surface will not weaken installation.
3 Installer must insure that fasteners used are of adequate strength and suitable
for the mounting surface chosen.
4 Entire bottom of case must be readily accessible after installation is complete.
5 Hinge that connects bottom panel and automatic trap door of screen must be
permitted to operate freely. Front and back of case must be straightânot forced
to warp or bow. Hinges must be free from mastic or paint buildup, and doors
must be unobstructed by ceiling tiles.
6 Do not use screen case to support adjacent sections of ceiling.
7 If trim pieces must be attached to case, do not permit screws to protrude more
than 1/4" through 1/8" wall of case. Do attach trim pieces with nails.not
8 If case is painted, slots on bottom of case should be shielded to protect viewing
surface from paint splatters or overspray.
9 Do not seal unit in ceiling until electrical connections have been made and
screen has been operated successfully.
Copyright Š 2014 Draper Inc. Form SignatureE&V_Inst14 Printed in U.S.A.
Caution
1 Read instructions through completely before proceeding. Follow instructions
carefully. Installation contrary to instructions invalidates warranty.
2 Pick up screen case from ends only. Picking case up at other points will damage
case and .may damage fabric
3 To insure a safe installation, the of the unit MUST BE supported by entire weight
the end-plates.
4 Entire bottom of screen case should be unobstructed to permit proper operation of
automatic trap door, and access to bottom panel for making electrical connections
or servicing.
5 Screen should be installed level (using a carpenterâs level).
6 Nothing should be fastened to screen dowel or viewing surface.
7 Operating switch(es) is packed separately in screen carton. Do not discard with
packing material.
8 Screen operates on 110-120V, 60 Hz., 1.1 amp current draw for models using
small case; 1.3 for models using large case (see page 2).
NOTE: Screen has been thoroughly inspected and tested at factory and found to be
operating properly prior to shipment.
These instructions are meant as a guide only. They do not imply any responsibility on
the part of Draper, Inc. for improper installation or faulty workmanship at the jobsite.
Please Note: Instructions for adjusting Draperâs Tab-Tension System for Series V
screens are on page 2.
If you encounter any difďŹculties installing or servicing your Signature, call your dealer or
Draper, Inc., Spiceland, Ind., (765) 987-7999 or fax (765) 987-7142.
Suitable for use in environmental air space in accordance with Section
300-22(c) of the National Electrical Code, and Sections 2-128, 12-010(3)
and 12-100 of the Canadian Electrical Code, Part 1, CSA C22.1.
Brackets installed with rivets at factory.
Bracket spacing:
â˘îSmallîCaseîConstructionî/Eîorî/V
-Case length <95"-no brackets required
-Case length >95"-1 bracket centered
â˘îLargeîCaseîConstructionî/Eîorî/V
-2 brackets equally spaced
3/ " (9.5mm) -16 threaded rod8
(use for suspending
screen) by others.
Case support
bra ets NOTck .
for use in
supporting
weight of case.
5/ " (8mm)-18 threaded rod16
(use for adjusting
deflection) by others.
3/ " (9.5mm)-16 threaded rod8
(use for suspending
screen) by others.
Electrical Connections
Screen operates on 110-120v, 60 Hz., 1.1 amp current draw for models using
small case; 1.3 for models using large case (see page 2). Junction box is located
just above the access plate at left end of screen. (See chart on back of this sheet.)
Access plate is held closed with ďŹathead screws and may be opened with a
Phillips screwdriver. Automatic trap door does not need to be opened to make ďŹeld
connections. Removal of access plate exposes red, black and white pigtail leads
and green internal ground wire per wiring diagram attached. Screen is shipped with
internal wiring complete and control switch(es) fully boxed. Wire connecting screen
to switch(es) and switch(es) to power supply should be furnished by installer.
Connections should be made in accordance with attached wiring diagram, and
wiring should comply with National and local electrical codes.
All Operating Switches Should Be âOffâ Before Power Is Connected.
Shipping Support Bracket
Dowel (Series V)
US Patent No.
5,341,241
Case Dimensions & Methods of Installation
SCREEN SIZE CASE SIZE
Total Drop <156" or viewing width <144" Small
Total drop >156" or viewing width >144" Large
Signature/Series E & V by Draper Page 2 of 3
NOTE: Viewing surface shown
is Series V with tab tensioning.
Series E, without tab tensioning,
is also available.
www
.draperinc.com (765) 987-799
9
Case length
11/ " p2Ty
Viewing surface
21/ "8
A
Series A
E-small case 33/ "16
E-large case 41/ "2
V riesVa
Ceiling grid
and tile
(by others)
91/ "8
6"
9ž"
Audience
Electrical connection
to internal splice box
on left end of case. 7/ "8
kno out for ck 1/ " conduit.2
J-Bo
x cover located under
splice box.
Shown with
3
/ " threaded8
rod (provided
by others).
Ceiling grid and tile
(by others)
9
1/ "8
6"
11" Audience
Electrical connection
to internal splice box
on left end of case. 7/8"
kno out for ck 1/ " conduit.2
J-Bo
x cover located under
splice box.
Shown with
7
/ " threaded16
rod (provided
by others).
Ceiling grid and tile
(by others)
Small Signature Case Large Signature Case
Caution: Do not remove the roller assembly from the case unless
necessary for repairs. If the roller assembly is removed, be sure mo-
tor is fully re-seated in the bracket, and re-secure it carefully with the
motor retaining spring and screw (see diagram below).
Please note: Maximum
torque for tightening
screw is 5 lb-inches.
Brackets evenly spaced along screen case
C
O
U
N
T
E
R
-
C
L
O
C
K
W
I
S
E
ADJUSTMENT
SCREW
TENSIONING
CABLE
DOWEL
T
O
R
E
L
E
A
S
E
T
E
N
S
I
O
N
T
U
R
N
C
L
O
C
K
W
I
S
E
ADJUSTMENT
SCREW
TENSIONING
CABLE
DOWEL
T
O
I
N
C
R
E
A
S
E
T
E
N
S
I
O
N
T
U
R
N
Tab-Tension Adjustment Procedure
Draperâs Tab-Tensioning System is factory-set, and under normal circumstances will not require ďŹeld adjustment.
If, however, you notice wrinkles, waves or other indications that the tensioning cables need to be adjusted, follow the procedure below.
1 Determine which side requires adjustment.
2 Secure dowel with one hand.
3 Using Phillips-head screwdriver, depress spring-loaded adjustment screw and slowly turn CLOCKWISE TO INCREASE tension,
or COUNTER-CLOCKWISE TO RELEASE tension. The screw adjusts in Âź turn increments. Adjust only one increment (Âź turn) at a time
4 If problem is not corrected, leave screen in position for 24 hours to allow surface material to stretch into position.
5 If problem still is not corrected, repeat steps 2 and 3.
Caution: Do not touch
or bend surface.
Wiring Diagrams
Single Station Control
Internal Screen Wiring
White (Common)
Black (Down)
Red (Up)
Green (Ground)
Dashed wiring
by electrician
Control
switch
Single gang box otheby
Min. 4" x 2
1
/
8
" x 1
7
/
8
" dee
Blue
Black
Red
Location of yke
operated on-off
switch if furnished
To 110-120V Line
Two-Way Serial Communication (RS232) with MC1
See separate Serial Communica-
tion-RS232 Instruction sheet for
enabling RS232 with the MC1.
3 Button ll Switch Wa
DOWN - Black
COM - White
UP - Red
White-Common to screen & 110-120V lAC Neutra
Red-to screen (directional)
Brown-to screen (directional)
Yellow-to 110-120V -HotAC
Black-to 110-120V -HotAC
Green-Ground
Eye Port r IR Ey RF Receiver or LEDfo e,
Wall Switch For more than one of .
these, a splitter is required.
Aux Port for connecting additional C-III LV
modules (up to six total can be linked-
connect from Aux to Eye).
Dashed wiring electricianby
Low ltage wi ng othersvo ri by
White (Common)
Red (Up)
Bla (D n)ck ow
Green (Ground)
Location of yke
operated on-off
switch if fu ishedrn
To
110-120V
Line
Inte al Screen Wiringrn
STOP
Control
Switches
24v DC
STOP
Low Voltage & Wireless Control
RS232 Data FROM Control System
RS232 Data Control SystemTO
Signal Ground & Manual Switch Common
Manual Switch Down
Manual Switch Up
White-Common to screen & 110-120V lAC Neutra
Red-to Screen (directional)
Br n-to Screen (directional)ow
Black-Hot to 110-120V AC
Green/Yellow-Ground
Fuse
Program LED
Eye for IR EyPort e. r RF Receiver or LEDFo
Wall Switch, a Splitter and a Power Supply
is required. Plug RF Receiver or LED ll Wa
Switch and then Power Supply into splitter,
run cable from Splitter to MC1 Eye .Port
Low Voltage Wi ng othersri by
AC Wi ng electricianri by
MC1
White (Common)
Red (Up)
Black (D n)ow
Green (Ground)
Inte al Screen Wiringrn
Location of yke
operated on-off
switch if fu ishedrn
To
110-120V
Line
STOP
Control
Switches
24v DC
STOP
Please Note: Do not wire motors in parallel.
Signature/Series E & V by Draper Page 3 of 3
Multiple Station Control
Internal Screen Wiring
White (Common)
Black (Down)
Red (Up)
Green (Ground)
Dashed wiring
by electrician
Red
Red
Black
Blue
Blue
Cap off with wire
nut and tape
Black
Red Blue
Black Single gang box othersby
Min. 4" x 2
1
/
8
" x 1
7
/
8
" deep.
3 shown. More or less equally
feasible.
Location of yke
operated on-off
switch if furnished
To 110-120V Line
www
.draperinc.com (765) 987-799
9
Produktspezifikationen
| Marke: | Draper |
| Kategorie: | Projektionsfläche |
| Modell: | Signature E |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Draper Signature E benĂśtigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Projektionsfläche Draper
7 September 2024
5 September 2024
3 August 2024
2 August 2024
2 August 2024
2 August 2024
1 August 2024
31 Juli 2024
31 Juli 2024
29 Juli 2024
Bedienungsanleitung Projektionsfläche
- Projektionsfläche Da-Lite
- Projektionsfläche Pyle
- Projektionsfläche Optoma
- Projektionsfläche Kodak
- Projektionsfläche NEC
- Projektionsfläche Celexon
- Projektionsfläche Elite
- Projektionsfläche AV:link
- Projektionsfläche Oregon Scientific
- Projektionsfläche Duronic
- Projektionsfläche GPX
- Projektionsfläche Luxburg
- Projektionsfläche EluneVision
- Projektionsfläche Stewart
- Projektionsfläche Elite Screens
- Projektionsfläche Lumene
- Projektionsfläche Avers
- Projektionsfläche Elite ProAV
- Projektionsfläche KHOMO GEAR
- Projektionsfläche EPV
Neueste Bedienungsanleitung fĂźr -Kategorien-
12 Oktober 2024
2 Oktober 2024
29 September 2024
27 September 2024
20 September 2024
11 September 2024
6 September 2024
6 September 2024
5 September 2024
4 September 2024