Draper Cineperm Bedienungsanleitung
Draper
Projektionsfläche
Cineperm
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Draper Cineperm (1 Seiten) in der Kategorie Projektionsfläche. Dieser Bedienungsanleitung war für 25 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/1
Installation Instructions
Cineperm Permanently Tensioned Projection Screen by Draper
Copyright © 2011 Draper Inc. Form Cineperm_Inst11 Printed in U.S.A.
Frame Assembly
Standard Frame—
① Lay out frame pieces on fl oor, by matching up color-coded tape near
corners. Snaps should be facing up.
② Assemble frame (see Fig. 1). If nec es sary gently tap frame ends with a
rubber mallet to make sure castings are fully seated.
Surface Installation
① Carefully remove surface from cardboard tube and unroll onto a clean
cloth or paper.
② Engage snaps in each corner, then secure rest of screen snaps.
③ Stretch fabric across frame. Use extreme caution when attaching fabric.
Overstretching or rough handling could cause the viewing surface to tear.
Frame Installation (Standard Frame)
Outside (Face) Mount—
① Drill mounting holes in frame (see Fig. 2).
② Mark wall and drill holes to correspond with those in the frame.
③ Enlarge holes in frame side furthest from wall to allow screw heads to pass
through (see Fig. 2). Do not allow screw heads to remain outside the
frame: overtightening could bend frame and affect screen fl atness.
Cineperm
frame
Mounting hardware
by others
Viewing surface snaps to
frame, covering mounting holes
Supporting structure
Drill through frame for
mounting hardware.
Enlarge first hole for screw
head to pass through.
Figure 2
Figure 3
Inside (Jamb) Mount—
① Place frame assembly in opening to check for a snug fi t. If frame is too
large, opening may have to be enlarged. If frame is too small or does not
sit square in the opening, shims and caulking may be required.
② Drill mounting holes in frame, and enlarge the fi rst holes to allow screw
heads to pass through (see Fig. 3). Do not allow screw heads to remain
outside the frame: overtightening could bend frame and affect screen
fl atness.
③ Drill holes in jamb.
④ Attach frame using appropriate fasteners for mounting surface (provided
by others).
⑤ Use caulk to ensure there is no light leakage around edges of frame.
Truss Frame—
① Unfold and lay out pieces on fl oor, by matching up color coded marks.
Lock all hinges (see Fig. 1). Stage Left and Stage Right sections should be
placed with snaps . Top and bottom sections should be placed with up
snaps down.
② To increase frame rigidity, hinges on top and bottom sections have rivnuts
marked with red and green. Insert a Handy Crank through the threadless
rivnut (red) and tighten into the threaded rivnut (green).
③ Apply small sections marked “Stiffener Bars” to back of bottom frame
section, using 8 Handy Cranks. These eliminate sag on large suspended
frames. Failure to use all Handy Cranks may result in screen frame
damage. Turn bottom frame section over so snaps face up.
④ Repeat step 3 for top frame section.
⑤ Join top and bottom sections to Stage Left and Stage Right, using 2
Handy Cranks on each of the 4 corners. Match numbers on white labels.
NOTE: No Handy Crank should protrude outside screen frame.
⑥ Attach surface (see “Surface Installation”), and suspend using appropriate
materials (provided by others to meet specifi c installation requirements).
Opening
Wall
Anchor bolt by others.
Clearance hole in outer
wall by others.
Snap-on viewing surface
1" square
alum. tube
Wall
Anchor bolt by others.
Clearance wall in outer
wall by others.
Locate between snaps. 1 square
alum. tube
Snap-on viewing surface
Inside (Jamb) Mount
Outside (Face) Mount
④ Attach frame to wall using appropriate fasteners for mounting surface
(provided by others).
NOTE: Measure screen frame width at the top, bottom, and center; Make
sure the frame is installed so the center width is same as the width at
the top and bottom.
Figure 1
Standard Frame Truss Style Frame
Caution
① Read instructions through completely before pro ceed ing.
② Follow instructions carefully. Installation con trary to instructions
invalidates warranty.
③ Bent or warped frames will affect surface fl atness and image quality.
④ Screen should be square, and width should not vary from the center to
the ends of the frame
⑤ When lifting assembled screen, do not lift at only one corner; lift at both
corners. Lifting by one corner could result in damage to the screen
frame, especially on large screens.
⑥ Screen should be installed level (using a carpenter’s level).
⑦ Nothing should be fastened to screen frame or viewing surface.
⑧ Be careful not to rip screen material when attaching surface to frame.
⑨ The ideal temperature range for assembling this screen to prevent
damaging the surface is 68°-78° F (20°-26° C). Assembling below
recommended temperatures may damage surface and void warranty.
NOTE: Screen has been inspected and tested at factory prior to shipment.
Jamb of opening
Viewing Surface snaps to
frame, covering mounting holes
Cineperm
frame
Drill through frame for
mounting hardware. Enlarge
first hole for screw head
to pass through.
Mounting hardware
by others
Color-coded
tape
®
Handy
Cranks
If you encounter any diffi culties installing or servicing your Cineperm, call your
dealer or Draper, Inc. in Spiceland, In di ana, 765-987-7999, or fax 765-987-7142.
Always fold viewing surface with snaps face-to-face.
Do not permit screen fabric to contact border material
or snaps when folded. Store in pouch provided.
Produktspezifikationen
| Marke: | Draper |
| Kategorie: | Projektionsfläche |
| Modell: | Cineperm |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Draper Cineperm benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Projektionsfläche Draper
7 September 2024
5 September 2024
3 August 2024
2 August 2024
2 August 2024
2 August 2024
1 August 2024
31 Juli 2024
31 Juli 2024
29 Juli 2024
Bedienungsanleitung Projektionsfläche
- Projektionsfläche Da-Lite
- Projektionsfläche Pyle
- Projektionsfläche Optoma
- Projektionsfläche Kodak
- Projektionsfläche NEC
- Projektionsfläche Celexon
- Projektionsfläche Elite
- Projektionsfläche AV:link
- Projektionsfläche Oregon Scientific
- Projektionsfläche Duronic
- Projektionsfläche GPX
- Projektionsfläche Luxburg
- Projektionsfläche EluneVision
- Projektionsfläche Stewart
- Projektionsfläche Elite Screens
- Projektionsfläche Lumene
- Projektionsfläche Avers
- Projektionsfläche Elite ProAV
- Projektionsfläche KHOMO GEAR
- Projektionsfläche EPV
Neueste Bedienungsanleitung für -Kategorien-
12 Oktober 2024
2 Oktober 2024
29 September 2024
27 September 2024
20 September 2024
11 September 2024
6 September 2024
6 September 2024
5 September 2024
4 September 2024