Delta Dore Tyxia 2600 Bedienungsanleitung

Delta Dore Nicht kategorisiert Tyxia 2600

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Delta Dore Tyxia 2600 (1 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 3 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/1

Technical speciﬁcaons

- Power supply: Lithium 3 V CR2032 battery life

up to 8 years depending on use

- Class III insulation

- Storage temperature: -10°C / +50°C

- Operating temperature : -10°C / +40°C

- IP 40 (ﬂush mounting box)

Dimensions: 41 x 36 x 8 mm

- X3D wireless remote control device:

868.7 MHz to 869.2 MHz.

- Maximum wireless power < 10 mW

- Category 2 receiver

Battery powered multifunction transmitter

Tyxia 2600

Checking the transmitter operating mode.

- Brieﬂy press button A or B. The LED or LEDs ﬂash:

• LED A or B ﬂashing:

1 green ﬂash: lighting. Single ON/OFF switch

2 green ﬂashes: lighting. Single ON/OFF push button

Roller blind. Single sequential push button

32 green ﬂashes: lighting. Single dimmer push button

4 green ﬂashes: routines. Routines push button

• Two LEDs, A and B, ﬂashing:

1 green ﬂash: Roller shutter / Raise/Stop/Lower switch.

2 green ﬂashes: Roller shutter / Double push button

Raise/Stop/Lower.

3 green ﬂashes: Lighting / Double dimmer push button.

Pairing

- Press the transmitter button or buttons for 3 seconds (according to

conﬁguration) until the LED ﬂashes. Release.

Setup

- Press the transmitter button for 6 seconds. The LED ﬂashes, then

becomes steady, release.

<1/><2>Setting a receiver to pairing mode from the

transmitter</2>

- Press button A, B or A + B for 10 seconds until the red LED ﬂashes twice

in succession.

- Proceed with the pairing of a new product

Setting a receiver to pending deletion

from the transmitter

- Press button A, B or A + B for 15 seconds until the red LED ﬂashes 3

times in succession.

- Press the transmitter to be removed for 3 seconds: the link with the

receiver is removed.

Deleting all paired devices

- Press button A, B or A + B for 20 seconds until the red LED ﬂashes 4

times. Channels A, B, or A + B are removed from all the receivers.

Factory reset

- Press button A, B or A + B for 30 seconds until the LED or LEDs ﬂash then

switch off. The conﬁguration of channel A, B or A+B is reset (mode 1 by

default). Repeat the operation for each channel to reset.

If you wish to change the operating mode of the Tyxia 2600, you must

ﬁrst cancel all pairings (see function F).

Single or double . switch

Single or double push button

06/22

3’’

> > > >6’’ 10’’ 20’’ 30’’>15’’

E F GB D

Pairing

Factory

reset

Setup

Set to waiting to

pair

Deletion of all

paired devices

Set to pending

deletion

Summary of funcons

The Tyxia 2600 can control the lighting, lighting dimming,

roller shutters, control systems, and routines.

It is compatible with the following types of control system:

- Single or double switch.

- Single or double push button.

- 3-position roller shutter switch.

Local control wires can be extended up to 10 m

(separate from the 230 V).

COM

IN1

TYXIA

2600

COM

IN2

TYXIA

2600

> 6s

COM

IN1

TYXIA

2600

IN2

A A A

> 3s

TYXIA

2600

A B

1 2 23

A A A

> 6s

A B

TYXIA

2600

> 3s

... ... ...

TYXIA

> 3s

... ... ...

TYXIA

> 3s

COM

IN1

TYXIA

2600

COM

IN2

TYXIA

2600

> 6s

TYXIA

2600

A B

1 2 3

COM

IN1

TYXIA

2600

IN2

A A A

> 6s

... ... ...

TYXIA +

A B

TYXIA

2600

A A A A > 3s

> 3s

... ... ...

TYXIA

> 3s

Connection instructions for IN1 - COM - IN2 terminals

Connecon

Lighng usage mode Rounes usage mode

Roller Shuer user mode

Install the Tyxia 2600 in the

ﬂush mounting box of the switch.

Do not strip the wires when they are

connected to the product as you could

damage the internal connector.

TYXIA

2600

7mm

0,5 mm

KY31A02

IN1

COM

IN2

TYXIA

2600

A B

COM

IN1

TYXIA

2600

COM

IN2

TYXIA

2600

> 6s

A A A

1 2 3

... ... ...

TYXIA

> 3s

Create your routines

with the Tydom application.

You can also use the Tydom application to

create your routines.

Download the Tydom app.

Launch the Tydom app.

Select "Control" > Routines >

and follow the instructions.

Depending on your device:

Go to Google Play or the App Store and

search for and download the free "Tydom"

app.

Make sure that your smartphone/tablet is

connected to the local network.

- Use the wires supplied.

- Push the wire fully into the terminal.

Removal recommendations

Turn the wire

while pulling on it.

COM

IN1

COM

IN1

IN2

TYXIA

2600

COM

IN1

COM

IN1

IN2

TYXIA

2600

Battery replacement

Use a tool to remove the

battery.

CR2032

Your device is compa ble

with Tydom (except Tydom 1.0

and Tydom 2.0), to automate

your Smart Home.

Google Play is a registered trademark of

Google LLC. App Store is a service mark of

Apple Inc.

Lighting On/Off or Dimmer

Routines

Roller blind

Controlled via a 3 ﬁxed position

switch, or a double push button

Roller blind

Controlled by a

single push button

(sequential mode)

Lighting Dimmer

Controlled by a

double push button

Controlled by a

single push button

If you are using a single switch (default mode) go straight to step 4 "Pairing"

❶Buttons A and B can be conﬁgured separately.

Press the button for 6 seconds to conﬁgure (A or B). During these 6

seconds, the light ﬂashes once, then becomes steady, then you release.

❷ To select the type of switch, repeatedly press button A. LED A or B (de-

pending on the conﬁgured channel) will ﬂash a speciﬁc number of times to

indicate the current operating mode.

❸ Conﬁrm the selected mode by pressing button B

for 3 seconds until LED A or B (depending on the conﬁgured channel) turns

steady green.

If you are using a 3-position hold switch (default mode)

go straight to step 4 "Pairing"

❶ Press buttons A and B at the same time and hold for 6 seconds. The red

LEDs ﬂash once, then ecome steady, then you release. The LEDs ﬂash

green a speciﬁc number of times to indicate the current operating mode.

❷ To select the other switch type,

press button A once to show 2 green ﬂashes.

❸ Conﬁrm the selected mode by pressing button B for 3 seconds

until the 2 LEDs turn steady green.

❶ Press buttons A and B simultaneously for 6 seconds.

The red LEDs ﬂash once, then switch on steady, then you can release.

❷ To select the type of switch, press button A twice to show 3 green

ﬂashes.

❸ Conﬁrm the selected mode by pressing button B for 3 seconds

until the 2 LEDs turn steady green.

❶Buttons A and B can be conﬁgured separately.

Press the button for 6 seconds to conﬁgure (A or B). During these 6 seconds,

the red light ﬂashes once, then becomes steady, then you release.

❷ To select the type of switch,

press button A once to show 4 green ﬂashes.

❸ Conﬁrm the selected mode by pressing button B for 3 seconds until LED

A or B (depending on the conﬁgured channel) turns steady green.

❶Buttons A and B can be configured separately.

Press the button for 6 seconds to configure (A or B).

During these 6 seconds, the red light flashes once, then becomes

steady, then you release.

❷ To select the type of switch,

press button A once to show 2 green ﬂashes.

❸

Conﬁrm the selected mode by pressing button B

for 3 seconds until LED A or B (depending on the conﬁgured channel)

turns steady green.

Select

the channel

to conﬁgure

Press

buttons

A and B

Press

buttons

A and B

Chan-

nel

Chan-

nel

2 separate channels

Select your switch type

Select your switch type Select your switch type

Single

switch

Default mode

Switch

Raise / Stop /

Lower

Default mode

Double push

button Raise /

Stop / Lower

ON/OFF

push

button

Push

button

Dimmer push

button Double dimmer +/-

push button Routines

push

button

Not

used

Not

used

Not

used

Not

used

Not

used

Not

used Not

used

Not

used

Not

used

Not

used

Conﬁrm

Conﬁrm Conﬁrm

1- Set the receiver(s)

to await pairing mode

(refer to the user guide).

1 - Set the receiver(s)

to await pairing mode

(refer to the user guide).

1 - Set the receiver(s)

to await pairing mode

(refer to the user guide).

1- Set the receiver(s)

to await pairing mode

(refer to the user guide).

1- Set the receiver(s)

to await pairing mode

(refer to the user guide).

2- On the Tyxia 2600: Send the pairing

order by pressing the button for the

channel to be paired (A or B) for 3

seconds.

2- On the Tyxia 2600: Send the pairing

order by pressing

the button for the channel to be paired

(A or B) for 3 seconds.

2- On the Tyxia 2600:

Send the pairing

order by pressing the buttons A and B

simultaneously for 3 seconds.

❹ ❹ Pairing Pairing ❹ Pairing

The products are paired if the LED of the receiver or receivers is no longer ﬂashing.

The products are paired if the LED of the receiver or receivers is no longer ﬂashing. The products are paired if the LED of the receiver or receivers is no longer ﬂashing.

The products are paired if the LED of the receiver or receivers is no longer ﬂashing.

Channel A: Dimmer +

Channel B : Dimmer --

Controlled by a single

switch or single push

button

2 separate channels

Select

the channel

to conﬁgure

Select

the channel