CyberPower PR1000ELCDRT2U Bedienungsanleitung

CyberPower Unterbrechungsfreies Stromversorgungssystem PR1000ELCDRT2U

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für CyberPower PR1000ELCDRT2U (12 Seiten) in der Kategorie Unterbrechungsfreies Stromversorgungssystem. Dieser Bedienungsanleitung war für 42 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/12

User’s Manual

Professional Rack Mount LCD Series

PR1000ELCDRT2U/PR1500ELCDRT2U/

PR2200ELCDRT2U

K01-0000431- 01

This manual contains important instructions. Please read and follow all instructions carefully during installation

and operation of the unit. Read this manual thoroughly before attempting to unpack, install, or operate the

UPS.

CAUTION! The UPS must be connected to a grounded AC power outlet with fuse or circuit breaker protection.

DO NOT plug the UPS into an outlet that is not grounded. If you need to power-drain this equipment, turn o

and unplug the unit .

CAUTION! The battery can power hazardous components inside the unit, even when the AC input power is

disconnected.

CAUTION! The UPS should be near the connected equipment and easily accessible.

CAUTION! To prevent the risk of re or electric shock, install in a temperature and humidity controlled indoor

area, free of conductive contaminants. (Please see specications for acceptable temperature and humidity

range).

CAUTION! To reduce the risk of electric shock, do not remove the cover, except to service the battery. an

There are no user serviceable parts inside, except for the battery.

CAUTION! To avoid electrical shock, turn off the unit and unplug it from the AC power source before servicing

the battery or installing a computer com ponent.

CAUTION! To reduce the risk of re, connect the UPS to a circuit with 16 amperes maximum over-current

protection in accordance CE requirement. to

CAUTION! The AC outlet where the UPS is connected should be close to the unit and easily accessible.

CAUTION! Please use only VDE-tested, CE-marked mains cable, (e.g. the mains cable of your equipment),

to connect the UPS to the AC outlet.

CAUTION! Please use only VDE-tested, CE-marked power cables to connect any equipment to the U PS.

CAUTION! When installing the equipment, ensure that the sum of the leakage current of the UPS and the

connected equipment does not exceed 3.5mA.

CAUTION! This is permanently connected equipment and only qualied maintenance personnel may carry

out installations.

CAUTION! Do not unplug the unit from AC Power during operation, as this will invalidate the protective

ground insulation.

CAUTION! DO NOT USE FOR MEDICAL OR LIFE SUPPORT EQUIPMENT! Under no circumstances this

unit should be used for medical applications involving life support equipment and/or patient care.

CAUTION! DO NOT USE WITH OR NEAR AQUARIUMS! To reduce the risk of re, do not use with or near

aquariums. Condensation from the aquarium can come in contact with metal electrical contacts and cause

the machine to short out.

CAUTION! DO NOT USE WITH LASER PRINTERS! The power demands of laser printers are too large for a

UPS.

DO NOT INSTALL THE UPS WHERE IT WOULD BE EXPOSED TO DIRECT SUNLIGHT OR NEAR A

STRONG HEAT SOURCE!

DO NOT BLOCK OFF VENTILATION OPENINGS AROUND THE HOUSING!

DO NOT CONNECT DOMESTIC APPLIANCES SUCH AS HAIR DRYERS TO UPS OUTPUT SOCKETS.

IMPORTANT SAFETY INSTRUCTIONS

UNPACKING

The box should contain the following:

(1) UPS unit x 1; (2) User manual x 1; (3) Phone line x 1; (4) PowerPanel® Business Edition software CD x 1; (5)

USB A+B type cable 1; (6) Rack mount Brackets x 2; (7) Emergency Power O Cable (gray) 1; (8) Serial x x

Interface Cable (DB- 1; (9) Power cord x 4 (Power cord x 6 for PR2200ELCDRT2U) 9) x

AUTOMATIC VOLTAGE REGULATOR(AVR)

The can stabiliz PR1000ELCDRT2U/PR1500ELCDRT2U/PR2200ELCDRT2U

the consistent utility power. The utility power may be damaging to important data

and hardware, but Automatic Voltage Regulation helps the computer not

experience dangerous voltage levels. Automatic Voltage Regulator automatically

regulates low or high voltages keep equipment working at safe AC power levels to

(220/230/240V) without switching to battery. Your equipment can operate normally

even meet the power problems, such as, shout brownouts and blackouts. The

unit’s powerful sealed lead-acid batteries will provide power only if the incoming

voltage drops below 150V or increases above 0V.30

SYSTEM BLOCK DIAGRAM

HARDWARE INSTALLATION GUIDE

1. Battery charge loss may occur during shipping and storage. The rst time the UPS is used, is strongly it

recommended to charge the batteries for at least hours to ensure that the batteries are at theirmaximum 12

charge capacity. To recharge the batteries, simply plug UPSinto an AC outlet, the batteries will charge

whether the UPS is powered on or not.

2. With the UPS o and unplugged, connect your computer, monitor, and any externally powered data

storage device (Hard drive, Tape drive, etc.) into the outlets. DO NOT plug a laser printer, copier, space

heater, vacuum, paper shredder or other large electrical device into the UPS. The power demands

of these devices will overload and possibly damage the unit.

3. To protect a fax, telephone, modem line or network cable, connect the telephone or network cable from the

wall jack outlet to the jack marked “IN” on the UPS. Then, connect a telephone cable or network cable from

the jack marked “OUT” on the UPS to the modem, computer, telephone, fax machine, or network device.

4. Plug the UPS into a 2 pole, 3 wire grounded receptacle (wall outlet). Make sure the wall branch outlet is

protected by a fuse or circuit breaker and does not service equipment with large electrical demands (e.g.

air conditioner, copier, etc). The warranty prohibits the use of extension cords, outlet strips, and surge

strips.

INSTALLING YOUR UPS SYSTEM (continued)

Produktspezifikationen

Marke:	CyberPower
Kategorie:	Unterbrechungsfreies Stromversorgungssystem
Modell:	PR1000ELCDRT2U
Display-Typ:	LCD
Breite:	433 mm
Tiefe:	388 mm
Gewicht:	25500 g
Produktfarbe:	Schwarz
Höhe:	88 mm
Energieschutzeigenschaften:	Over current, Over power, Over voltage, Overload, Short circuit
Anzahl USB 2.0 Anschlüsse:	1
Betriebstemperatur:	0 - 40 °C
Relative Luftfeuchtigkeit in Betrieb:	0 - 95 %
Anzahl Ethernet-LAN-Anschlüsse (RJ-45):	1
Reaktionszeit:	4 ms
LED-Anzeigen:	Leistung
Temperaturbereich bei Lagerung:	-15 - 45 °C
Mac-Kompatibilität:	Ja
Formfaktor:	Rackmount/Tower
Kompatible Betriebssysteme:	Windows 7/VISTA/XP/2000 Pro/ME/9 8/S e r v e r\n2003/2008, Mac, Linux
Ausgangsleistung:	700 W
Nachhaltigkeitszertifikate:	RoHS
Eingangsfrequenz:	50/60 Hz
Anzahl serielle Anschlüsse:	2
Anzahl der AC-Ausgänge:	8 AC-Ausgänge
Ausgangskapazität:	1 kVA
Modem (RJ-11) Port:	1
AC-Steckertypen:	C13-Koppler
Druckanstiegsschutz:	Ja
Nominale Eingang Spannung:	150-300 V
Nominale Ausgang Spannung:	230 V
Rack-Kapazität:	2U
Notstrom Aus (EPO):	Ja
Überspannungsschutz-Funktionen:	Fax, Modem