CyberPower CP350SLG Bedienungsanleitung

CyberPower Unterbrechungsfreies Stromversorgungssystem CP350SLG

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für CyberPower CP350SLG (2 Seiten) in der Kategorie Unterbrechungsfreies Stromversorgungssystem. Dieser Bedienungsanleitung war für 64 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/2

CP350SLG

User’s Manual

K01-0000662-00

Thank you for purchasing a CyberPower product. Please take a few minutes to register your product at

www.cyberpower.com. Registration certifies your product's warranty, confirms your ownership in the event of a

product loss or theft and entitles you to free technical support. Register your product now to receive the benefits of

CyberPower ownership.

(SAVE THESE INSTRUCTIONS)

This manual contains important safety instructions. Please read and follow all instructions carefully during installation

and operation of the unit. Read this manual thoroughly before attempting to unpack, install, or operate your UPS.

CAUTION! To prevent the risk of fire or electric shock, install in a temperature and humidity controlled indoor area free

of conductive contaminants. (Please see specifications for acceptable temperature and humidity range).

CAUTION! To reduce the risk of electric shock, do not remove the cover. There are no user serviceable parts inside.

CAUTION! Hazardous live parts inside can be energized by the battery even when the AC input power is

disconnected.

CAUTION! The UPS must be connected to an AC power outlet with fuse or circuit breaker protection. Do not plug into

an outlet that is not grounded. If you need to de-energize this equipment, turn off and unplug the unit.

CAUTION! To avoid electric shock, turn off the unit and unplug it from the AC power source before installing a

computer component.

CAUTION! To reduce the risk of fire, connect only to a circuit provided with 20 amperes maximum branch circuit over

current protection in accordance with the National Electric Code, ANSI/NFPA 70.

CAUTION! Not for use in a computer room as defined in the Standard for the Protection of Electronic Computer / Data

Processing Equipment, ANSI/NFPA 75.

CAUTION! Risk of explosion if battery is replaced by an incorrect type. Batteries shall be installed by service

personnel, and the replacement of batteries with a suitable recommended type. Dispose of used batteries according to

the instructions.

CAUTION! Do not dispose of batteries in a fire. The batteries may explode.

CAUTION! Do not open or mutilate batteries. Released electrolyte is harmful to the skin and eyes. It may be toxic.

DO NOT USE FOR MEDICAL OR LIFE SUPPORT EQUIPMENT! CyberPower Systems does not sell products for life

support or medical applications. use in any circumstance that would affect operation and safety of life support DO NOT

equipment, any medical applications or patient care.

DO NOT USE WITH OR NEAR AQUARIUMS! To reduce the risk of fire or electric shock, do not use with or near an

aquarium. Condensation from the aquarium can cause the unit to short out.

DO NOT USE THE UPS ON ANY TRANSPORTATION! To reduce the risk of fire or electric shock, do not use the unit

on any transportation such as airplanes or ships. The effect of shock or vibration caused during transit and the damp

environment can cause the unit to short out.

UNPACKING

Inspect the UPS upon receipt. The box should contain the following:

(a) UPS unit (b) User’s manual (c) Warranty registration card.

SYSTEM FUNCTION BLOCK DIAGRAM

HOW TO DETERMINE THE POWER REQUIREMENTS OF YOUR EQUIPMENT

1. Ensure that the equipment plugged into the outlet does not exceed the UPS unit’s rated capacity (350VA/255W for

CP350SLG). If the rated capacities of the unit are exceeded, an overload condition may occur and cause the UPS unit

to shut down or the circuit breaker to trip.

2. There are many factors that can affect the amount of power that your computer system will require. For optimal system

performance keep the load below 80% of the unit’s rated capacity.

HARDWARE INSTALLATION GUIDE

1. Your new UPS may be used immediately upon receipt. However, after

receiving a new UPS, to ensure the battery’s maximum charge capacity, it is

recommended that you charge the battery for at least 8 hours. Your UPS is

equipped with an auto-charge feature. When the UPS is plugged into an AC

outlet, the battery will automatically charge whether the UPS is turned on or

turned off.

2. With the UPS unit turned off and unplugged, connect your equipment requiring battery backup into the battery power

supplied outlets. Plug the other peripheral equipment (printer, scanner, speakers) into the full-time surge protection

outlets. DO NOT plug a laser printer, paper shredder, copier, space heater, vacuum, sump pump or other large

electrical device into the “Battery and Surge Protected Outlets”. The power demands of these devices will

overload and possibly damage the unit.

3. Plug the UPS into a 2 pole, 3 wire grounded receptacle (wall outlet). Make sure the wall

branch outlet is protected by a fuse or circuit breaker and does not service equipment

with large electrical demands (e.g. air conditioner, refrigerator, copier, etc…). The

warranty prohibits the use of extension cords, outlet strips, and surge strips.

4. Press the power switch to turn the unit on. The Power On indicator light will illuminate

green and the unit will “beep” twice.

5. If an overload is detected, an audible alarm will sound and the unit will emit one long beep. To correct this, turn the UPS

off and unplug at least one piece of equipment from the battery power supplied outlets. Make sure the circuit breaker is

depressed and then turn the UPS on.

6. To maintain optimal battery charge, leave the UPS plugged into an AC outlet at all times.

7. To store the UPS for an extended period, cover it and store with the battery fully charged. While in storage, recharge the

battery every three months to ensure battery life.

8. For pluggable equipment, the socket-outlet shall be installed near the equipment and shall be easily accessible.

DESCRIPTION

1. Battery and Surge Protected Outlets

The unit has three battery powered/surge suppression outlets to ensure temporary uninterrupted operation of your

equipment during a power failure. (DO NOT plug a laser printer, paper shredder, copier, space heater, vacuum,

sump pump or other large electrical device into the “Battery and Surge Protected Outlets.” The power demands

of these devices will overload and possibly damage the unit.)

2. Full-Time Surge Protection Outlets

The unit has three surge suppression outlets.

3. Power On Switch

To turn the UPS on, press the power button for approximately 2 seconds - you will hear a constant tone (1 second) -

and release after a short beep.

To turn the UPS off, press the power button for approximately 2 seconds - you will hear a constant tone (1 second) -

and release after two short beeps.

Quickly press the POWER button twice can turn off or turn on the audible Alarm. The default setting is for the Alarm On.

To turn the alarm off, quickly press the power button twice. You will hear two short beeps when the alarm is turned off.

To turn the alarm back on, quickly press the power button twice. You will hear a short beep when the alarm is turned on.

*When the alarm is turned off, there will be no audible notification when the UPS reaches a low battery state.

4. Power On Indicator (green)

This LED is illuminated when the utility power is normal and the UPS outlets are providing power, free of surges and

spikes.

5. Electrical Wiring Fault Indicator (red)

This LED indicator will illuminate to warn the user that a wiring problem exists, such as bad ground, missing ground or

reversed wiring. If this is illuminated, disconnect all electrical equipment from the outlet and have an electrician verify

the outlet is properly wired. The unit will not provide surge protection without being plugged into a grounded and

properly wired wall outlet.

6. Circuit Breaker

Located on the side of the UPS, the circuit breaker serves to provide overload and fault protection.

7. Outlets Designed for AC Adapters

The UPS unit has two widely-spaced outlets, so AC power adapters can be plugged into the UPS without overlapping

adjacent outlets.

Power ON

Wiring

Fault

Alarm

CONDITION

On Off Off Normal

Flash

when beeps Off Beep twice

every 30 seconds

Utility Failure - Battery mode

The UPS is providing power to battery power-supplied

outlets from its battery.

Flash

when beeps Off Rapid Beeping

every 1/2 second

Utility Failure – Low Battery

The UPS is providing battery power. Rapid beeping indicates

the unit will run out of power shortly.

On Off Constant tone

Overload - Occurs when connected equipment exceeds the

listed capacity of the UPS. Turn the UPS off, unplug at least

one piece of equipment from battery outlets, reset the circuit

breaker and turn the unit on.

On/Off On None

Electrical Wiring Fault - indicates a wiring problem This

with the AC outlet such as bad ground, missing ground, or

reversed wiring. Disconnect all electrical equipment from the

outlet and have an electrician check the outlet to insure

proper wiring.

Off Off Constant tone Utility Failure- The frequency is beyond 47-63Hz. The UPS

will not turn on in line mode.

Problem Possible Cause Solution

Full-time surge protection

outlets stop providing power

to equipment. Circuit

breaker button is projecting

from the side of the unit.

Circuit breaker has tripped due

to an overload.

Turn the UPS off and unplug at least one piece of

equipment. Reset the circuit breaker by depressing

the button, and then turn the UPS on.

The UPS does not perform

expected runtime.

Battery is not fully charged. Recharge the battery by leaving the UPS plugged in.

Battery is worn out. Please contact CyberPower Systems about

replacement batteries.

The UPS will not turn on.

The on/off switch is designed

to prevent damage from

rapidly turning it off and on.

Turn the UPS off. Wait 10 seconds and then turn the

UPS on.

The unit is not connected to an

AC outlet.

The unit must be connected to a 110/120V 50/60Hz

outlet.

The battery is worn out. Please contact CyberPower Systems about

replacement batteries.

Mechanical problem. Please contact CyberPower Systems.

The frequency is beyond

47-63Hz.

Turn the UPS off. Make sure the frequency range is

within 47-63Hz. Or you can turn on with battery

mode.

Additional troubleshooting information can be found at “Support” at www.cyberpower.com

DEFINITIONS FOR ILLUMINATED LED INDICATORS

BASIC OPERATION

INSTALLING YOUR UPS SYSTEM

TROUBLESHOOTING

IMPORTANT SAFETY WARNINGS

EMI Filter

Surge

Suppressor

Charger

AC/DC Battery

Inverter

Input Output

Normal Mode

Battery Mode

PRODUCT REGISTRATION

Model CP350SLG

Capacity 350VA/255W

Input Voltage on Utility 96V to 140V

Input Frequency 47 Hz to 63 Hz

On-Battery Output Voltage 120Vac ± 5%

On-Battery Output Frequency 50Hz/60Hz ± 1% (auto-sensing)

Transfer Time 4ms Typical

Max. Load for UPS Outlets (3 Outlets)

350VA/255W

Max. Load for Full-Time Surge

Protection outlets (6 Outlets) 10 Amps

On-Battery Output Wave Form Simulated Sine Wave

Operating Temperature + 32°F to 104° F / 0° C to 40° C

Operating Relative Humidity 0 to 95% non-condensing

Size (L x W x H) 7.1” x 4.3” x 3.2”

180 x 110 x 82 mm

Net Weight 3.5lbs/1.6kg

Typical Battery Recharge Time 8 hours typical from total discharge

Typical Battery Life 3 to 6 years, depending on number of discharge/recharge cycles

Recommended Battery Sealed Maintenance Free Lead Acid Battery

Safety Approvals UL1778(UPS), cUL CSA C22.2 No.107.3-05, FCC/DoC Class B

Advanced Energy-Saving Design

The GreenPower UPS™ has a high-efficiency charger, which makes it the most energy-efficient

UPS in its class. The advanced high-frequency charging system significantly improves charging

efficiency and conserves energy. As a result of this advanced design, the GreenPower UPS™

uses less energy compared to competitive models. The GreenPower UPS™ is manufactured in

accordance with the Restriction on Hazardous Substances (RoHS) directive making it one of the

most environmentally-friendly UPS on the market today.

FCC Compliance Statement

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device

may not cause harmful interference, and (2) this device must accept any interference received, including interference

that may cause undesired operation.

Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the

user's authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a

residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the instruction manual, may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the equipment and receiver.

 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

 Consult the dealer or an experienced radio/TV technician for help.

Canadian Compliance Statement

CAN ICES-3 (B)/NMB-3(B)

Read the following terms and conditions carefully before using the CyberPower CP350SLG (the “Product”). By using the

Product you consent to be bound by and become a party to the terms and conditions of this Limited Warranty and

Connected Equipment Guarantee (together referred to as this “Warranty”). If you do not agree to the terms and conditions

of this Warranty, you should return the Product for a full refund prior to using it.

Who is Providing this Warranty?

CyberPower Systems (USA), Inc. (“CyberPower”) provides this Limited Warranty.

What Does This Warranty Cover?

This warranty covers defects in materials and workmanship in the Product under normal use and conditions. It also covers

equipment that was connected to the Product and damaged because of the failure of the Product.

What is the Period of Coverage?

This warranty covers the Product for three years and connected equipment for as long as you own the Product.

Who Is Covered?

This warranty only covers the original purchaser. Coverage ends if you sell or otherwise transfer the Product.

How Do You Get Service?

1. Call us at (877) 297-6937 or write to us at Cyber Power Systems (USA), Inc., 4241 12

th Ave. E., STE 400, Shakopee,

MN 55379 or send us an e-mail message at claims@cyberpowersystems.com for instructions.

2. When you contact CyberPower, identify the Product, the Purchase Date, and the item(s) of Connected Equipment.

Have information on all applicable insurance or other resources of recovery/payment that are available to the Initial

Customer and Request a Claim Number.

3. You must provide a dated Proof-of-Purchase receipt (or other proof of the original purchase) and provide a

description of the defect.

How Do You Open A Connected Equipment Claim?

1. Call us at (877) 297-6937 or write to us at Cyber Power Systems (USA), Inc., 4241 12th Ave. E., STE 400,

Shakopee, MN 55379, or send us an e-mail message at claims@cpsww.com for instructions, within 10 days of the

occurrence.

2. When you contact CyberPower, identify the Product, the Purchase Date, and the item(s) of Connected Equipment.

Have information on all applicable insurance or other resources of recovery/payment that are available to the Initial

Customer and Request a Claim Number.

3. You must provide a dated purchase receipt (or other proof of the original purchase) for the Cyber Power unit and

connected equipment. You also need to provide a description of the damage to your connected equipment.

4. Pack and ship the product to CyberPower and, if requested, the item(s) of Connected Equipment, a repair cost

estimate for the damage to the Connected Equipment, and all claim forms that CyberPower provides to you. Show the

Claim Number on the shipping label or include it with the product. You must prepay all shipping costs, you are

responsible for packaging and shipment, and you must pay the cost of the repair estimate.

How Long Do I Have To Make A Claim?

All claims must be made within ten days of the occurrence.

What Will We Do To Correct Problems?

CyberPower will inspect and examine the Product.

If the Product is defective in material or workmanship, CyberPower will repair or replace it at CyberPower's expense, or, if

CyberPower is unable to or decides not to repair or replace the Product (if defective) within a reasonable time, CyberPower

will refund to you the full purchase price you paid for the Product (purchase receipt showing price paid is required).

If it appears that our Product failed to protect any equipment plugged into it, we will also send you forms for making your

claim for the connected equipment. We will repair or replace the equipment that was damaged because of the failure of our

Product or pay you the fair market value (NOT REPLACEMENT COST) of the equipment at of the time of the damage. We

will use Orion Blue Book, or another a third-party valuation guide, or eBay, craigslist, or other source to establish that amount.

Our maximum liability is limited to $75,000 for the CP350SLG.

Who Pays For Shipping?

CyberPower will pay when we send items to you; you pay when you send items to CyberPower.

What isn’t covered by the warranty?

1. This Warranty does not cover any software that was damaged or needs to be replaced due to the failure of the Product

or any data that is lost as a result of the failure or the restoration of data or records, or the reinstallation of software.

2. This Warranty does not cover or apply to: misuse, modification, operation or storage outside environmental limits of the

Product or the equipment connected to it, nor for damage while in transit or in storage, nor if there has been improper

operation or maintenance, or use with items not designed or intended for use with the Product, such as laser printers,

appliances, aquariums, medical or life support devices, etc.

What are the Limitations?

The sole and exclusive remedies of the Initial Customer are those provided by this Warranty.

1. This Warranty does not apply unless the Product and the equipment that was connected to it were connected to

properly wired and grounded outlets (including compliance with electrical and safety codes of the most current

electrical code), without the use of any adapters or other connectors.

2. The Product must have been plugged directly into the power source and the equipment connected to the Product must

be directly connected to the Product and not “daisy-chained” together in serial fashion with any extension cords,

another Product or device similar to the Product, surge suppressor, or power tap. Any such installation voids the

Limited Warranty.

3. The Product and equipment connected to it must have been used properly in a suitable and proper environment and in

conformance with any license, instruction manual, or warnings provided with the Product and the equipment

connected to it.

4. The Product must have been used at all times within the limitations on the Product’s VA capacity.

The Product was designed to eliminate disrupting and damaging effects of momentary (less than 1ms) voltage spikes or

impulses from lightning or other power transients. If it can be shown that a voltage spike lasting longer than 1ms has

occurred, the occurrence will be deemed outside the rated capabilities of the Product and the Limited Warranty is void.

CyberPower Does Not Cover or

Undertake Any Liability in Any Event for Any of the Following:

1. Loss of or damage to data, records, or software or the restoration of data or records, or the reinstallation of software.

2. Damage from causes other than AC Power Line Transients, spikes, or surges on properly installed, grounded and

code-compliant 120 volt power lines in the United States and Canada; transients, surges or spikes on standard

telephone land lines, PBX telephone equipment lines or Base 10T Ethernet lines, when properly installed and

connected. (This exclusion applies, for example, to fluctuations in data transmission or reception, by CATV or RF

transmission or fluctuations, or by transients in such transmission.)

3. Damage from any circumstance described as excluded above with respect to the Product.

4. Damages from fire, flood, wind, rain, rising water, leakage or breakage of plumbing, abuse, misuse or alteration of

either the product or the Connected Equipment.

5. CyberPower excludes any liability for personal injury under the Limited Warranty and Connected Equipment

Guarantee. CyberPower excludes any liability for direct, indirect, special, incidental or consequential damages,

whether for damage to or loss of property [EXCEPT FOR (AND ONLY FOR) the specific limited agreement of

CyberPower to provide certain warranty benefits regarding "Connected Equipment" under this Warranty], loss of

profits, business interruption, or loss of information or data. NOTE: Some States or Provinces do not allow the

exclusion or limitation of incidental or consequential damages, so the above limitation may not apply to you.

6. The Product is not for use in high-risk activities or with aquariums. The Product is not designed or intended for use in

hazardous environments requiring fail-safe performance, or for use in any circumstance in which the failure of the

Product could lead directly to death, personal injury, or severe physical or property damage, or that would affect

operation or safety of any medical or life support device (collectively, "High Risk Activities"). CyberPower expressly

disclaims any express or implied warranty of fitness for High Risk Activities or with aquariums. CyberPower does not

authorize use of any Product in any High Risk Activities or with Aquariums. ANY SUCH USE IS IMPROPER AND IS A

MISUSE OF THE PRODUCT.

The application of the United Nations Convention of Contracts for the International Sale of Goods is expressly excluded.

CyberPower is the warrantor under this Limited Warranty.

Where Can I Get More Information?

For further information please feel free to contact CyberPower at CyberPower Systems (USA), Inc. 4241 12 th Ave E., STE

400, Shakopee, MN 55379; call us at (877) 297-6937; or send us an e-mail message at claims@cyberpowersystems.com.

TECHNICAL SPECIFICATIONS

Limited Warranty and Connected Equipment Guarantee

CYBERPOWER GREENPOWER UPS™ TECHNOLOGY

Safety Compliance Statement

Produktspezifikationen

Marke:	CyberPower
Kategorie:	Unterbrechungsfreies Stromversorgungssystem
Modell:	CP350SLG
Akustische Signale:	Ja
Produktfarbe:	Schwarz
Akku-/Batterietyp:	12V/3.6AH
Akkuladezeit:	8 h
Akku-/Batterietechnologie:	Plombierte Bleisäure (VRLA)
Betriebstemperatur:	0 - 40 °C
Zertifizierung:	ETL
Kabellänge:	1.52 m
LED-Anzeigen:	Ja
Formfaktor:	Kompakt
Ausgangsleistung:	255 W
Eingangsfrequenz:	50/60 Hz
Abmessungen (B x T x H) (in Zoll):	7.1 x 3.2 x 4.3 "
Anzahl der AC-Ausgänge:	6 AC-Ausgänge
USV-Topologie:	Standby (Offline)
Ausgangskapazität:	0.35 kVA
Modem (RJ-11) Port:	1
AC-Steckertypen:	NEMA 5–15R
Typische Backup-Zeit bei halber Belastung:	8 min
Typische Backup-Zeit bei voller Belastung:	2 min
EMI/RFI Lautstärkefilter:	Ja
Nominale Eingang Spannung:	96-140 V
Nominale Ausgang Spannung:	120 V
Hot-Swap-Batterie:	Nein
Gewicht (imperial):	3.5 Pfund
Anstieg der Energiemenge:	810 J