Crestron Green Light GLA-EXPEX Bedienungsanleitung

Crestron WLAN-Repeater Green Light GLA-EXPEX

Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr Crestron Green Light GLA-EXPEX (2 Seiten) in der Kategorie WLAN-Repeater. Dieser Bedienungsanleitung war fĂĽr 8 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/2
Further Inquiries
To locate specific information or resolve questions after reviewing this guide, contact Crestron's True Blue Support at
1-888-CRESTRON [1-888-273-7876] or, for assistance within a particular geographic region, refer to the listing of
Crestron worldwide offices at www.crestron.com/offices.
To post a question about Crestron products, log onto Crestron’s Online Help at www.crestron.com/onlinehelp.
First-time users must establish a user account to fully benefit from all available features.
Future Updates
As Crestron improves functions, adds new features, and extends the capabilities of the GLA-EXPEX, additional
information may be made available as manual updates. These updates are solely electronic and serve as
intermediary supplements prior to the release of a complete technical documentation revision.
Check the Crestron website periodically for manual update availability and its relevance. Updates are identified as
an “Addendum” in the Download column.
WARNING: To a id fire, sh , vo ock or death turn; off po rc ea use nd power is be ore wer at ci uit br ker or f a test that off f
wiring!
NOTES: Observe the following points.
• To be installed and used in accordance with appropriate electrical codes and regulations.
• This product should be installed by a qualified electrician.
PREPARING AND CONNECTING WIRES
Strip the ends of the wires approximately 1/4 in (6 mm). Use care to avoid nicking the conductors. Twist together
the ends of the wires that share a connection. Apply solder only to the ends of the twisted wires. Avoid tinning too
far up the wires or the end becomes brittle.
Crestron Electronics, Inc. Installation Guide - DOC. 7212C
15 Volvo Drive Rockleigh, NJ 07647 (2036184)
Tel: 888.CRESTRON 06.14
Fax: 201.767.7576 Specifications subject to
www.crestron.com change without notice.
Crestron GLA-EXPEX
Crestron Green Light® Wireless Expander for infiNET EX® Networks
Installation Guide
Regulatory Compliance
Federal Communications Commission (FCC) Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following conditions: (1) This device may not
cause harmful interference and (2) this device must accept any interference received, including interference that may cause
undesired operation.
CAUTION: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the
user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help
Industry Canada (IC) Compliance Statement
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference and (2) this device must accept any interference, including interference
that may cause undesired operation of the device.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser)
gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type
and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for
successful communication.
This radio transmitter, IC: 5683C-CWD7191, has been approved by Industry Canada to operate with the antenna types listed
below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not
included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this
device.
Antenna Type: Dipole, Maximum permissible antenna gain: 2.5 dBi, Impedance: 50 Ohms
(Continued on following page)
DESCRIPTION
The Crestron Green Light
® GLA-EXPEX is a 2-way RF wireless expander designed to extend
the range of Crestron® lighting control products in an infiNET EX
® network. The GLA-EXPEX
is optimized for installation in building systems where a hard-wired expander is necessary.
Suitable for installation in plenum airspace, the GLA-EXPEX is built with a metal enclosure
that mounts directly to a 4-inch square electrical box. Additionally, the GLA-EXPEX accepts a
range of line voltages from 100 to 277 volts, which makes it easy to install in almost any
location. Up to five GLA-EXPEXs can be deployed in any infiNET EX network.
infiNET EX
Ultra-reliable infiNET EX wireless technology provides steadfast 2-way RF communications
throughout a residential or commercial structure without the need for physical control wiring.
Employing a 2.4 GHz mesh network topology, each infiNET EX device functions as an
expander, passing command signals through to every other infiNET EX device within range
(approximately 150 feet or 46 meters indoors), ensuring that every command reaches its
intended destination without disruption.*
The GLA-EXPEX communicates with a Crestron control system via an infiNET EX wireless
gateway (CEN-RFGW-EX, DIN-AP3MEX, or MC3—all sold separately). Up to 100 infiNET
EX devices, including Cameo® wireless keypads and in-wall switches (sold separately), may
coexist on a single wireless network, and every device that is added to the network
effectively increases the range and stability of the entire network by providing multiple
redundant signal paths.* Built-in dynamic frequency allocation continuously monitors RF
conditions and automatically selects the clearest channel to prevent interference from
neighboring networks, cordless phones, and microwaves.
Specifications
Specifications for the GLA-EXPEX are listed in the following table.
GLA-EXPEX Specifications
Physical Description
This section provides information on the connections, controls, and indicators available on
the GLA-EXPEX.
GLA-EXPEX Overall Dimensions (Flying Leads Not Shown)
(8x) ø3/16
Mounting holes for
two 4x4 boxes.
32
9 13/16 in
(251 mm)
3 5/16 in
(85 mm)
15/16 in
(24 mm)
3 3/8 in
(86 mm)
8 11/16 in
(221 mm)
2 1/2 in
(64 mm)
3 3/8 in
(86 mm)
3 3/16 in
(81 mm)
1 5/8 in
(42 mm)
4 1/4 in
(108 mm)
2 1/8 in
(54 mm)
Feed-through wires from
unit exit from this side.
1
DEVICE STATUS
The LED on the front of the GLA-EXPEX communicates the operational status of the
device.
The red LED lights when the GLA-EXPEX is not acquired by a gateway or not
communicating with a gateway.
The red LED also lights while the GLA-EXPEX powers up.
The green LED lights when the unit is successfully acquired and communicating with a
gateway.
WIRELESS COMMUNICATIONS
The device connects to the Crestron network via the infiNET EX communications protocol.
Use the procedures outlined below to join or leave an infiNET EX network and to verify
communications between the device and the control system.
Joining an infiNET EX Network
Before a device can be used in a lighting system, it must first join an infiNET EX network by
being acquired by an infiNET EX gateway.
NOTE: A device can be acquired by only one gateway.
1. Put the infiNET EX gateway into mode from the unit itself or from Crestron Acquire
Toolbox™, as described in its manual at www.crestron.com/manuals.
NOTE: In an environment where multiple gateways are installed, only one gateway
should be in mode at any time.Acquire
2. Place the device into mode.Acquire
a. Tap the button three times then press and hold it down STATUS
(tap-tap-tap-press+hold) until the LED on the device blinks once from amber to red
(this can take up to 10 seconds).
b. Release the button to start the acquire process. The GLA-EXPEX LED starts to
slowly blink, alternating between red and green to show that the device is actively
scanning the infiNET EX network.
• The device is acquired when the red LED lights for 5 seconds.
• The LED starts to blink alternately between amber and red to indicate that the
device was not successfully acquired. Press the button to STATUS
acknowledge failure. Ensure gateway is in mode and within range Acquire
before attempting the acquire process again.
3. Once all devices have been acquired, take the gateway out of mode. Refer to Acquire
the gateway’s operations guide, as described in its manual.
Leaving an infiNET EX Network
To leave an infiNET EX network put the device into mode, as described in “Joining Acquire
an infiNET EX Network” above, when no gateway is in mode.Acquire
Verifying Communications Status
To check the communications status of the device tap the button three times then STATUS
press and hold it down (tap-tap-tap-press+hold) for less than 2 seconds. The LED indicates
the communication status. Refer to the following table for details.
Connectors, Controls, and Indicators
Important Notes
Read before wiring and installation.
CAUTION: To be installed with 14 AWG (2.5 mm²) wire that complies with local electrical
codes.
WIRING
WARNING: Turn off power to the GLA-EXPEX before wiring. Wiring with the power on
can result in serious personal injury and damage to the device.
Typical Wiring Diagram
GLA-EXPEX
100–277 Vac
50/60 Hz
Line Power
COM NEUT GROUND
* Any infiNET EX device that provides expander functionality effectively extends the range of the wireless
network beyond the initial range of the gateway. Battery-powered infiNET EX devices do not provide
expander functionality.
# CONNECTORS,
CONTROLS, AND
INDICATORS
DESCRIPTION
1
Connections:
HOT: (1) 14 AWG Class 1 flying lead, black
NEUT: (1) 14 AWG Class 1 flying lead, white
GROUND: (1) 14 AWG Class 1 flying lead,
green with yellow stripe
2 Antenna (1) Connection for supplied antenna
3 STATUS LED and recessed miniature push button for
enabling mode Setup
LED COMMUNICATIONS STATUS
Turns on for 5 seconds Device is communicating with the control system.
Blinks three times Device is communicating with the gateway but the
gateway is not communicating with the control system.
Blinks twice Device was previously joined to the network but is not
communicating with the gateway.
Blinks once Device is not joined to the network.
SPECIFICATION DETAILS
Wireless
RF Transceiver
infiNET EX 2-way RF, 2.4 GHz ISM Channels 11–26
(2400 to 2483.5 MHz), default channel 15;
IEEE 802.15.4 compliant
Range (typical) 150 feet (46 meters) indoor, 250 feet (77 meters)
outdoor to nearest mesh network device(s);
Subject to site-specific conditions and individual
device capabilities*
Gateway Requires an infiNET EX gateway (sold separately)
Power Requirements 100–277 Vac, 50/60 Hz
Environmental
Temperature
Humidity
32° to 104°F (0° to 40°C)
10% to 90% RH (non-condensing)
Enclosure 20-gauge galvanized steel enclosure;
Designed for mounting to two adjacent standard 4 in
square electrical junction boxes
Dimensions
Height
Width
Depth
4 1/4 in (108 mm)
8 11/16 in (221 mm);
9 13/16 (250 mm) with antenna at 90° angle
2 in (51 mm)
Weight 2 lb (907 g)
Regulatory Compliance (Continued)
Industrie Canada (IC) Déclaration de conformité
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de
l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type
et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de
brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la
puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication
satisfaisante.
Le présent émetteur radio , IC: 5683C-CWD7191, a été approuvé par Industrie Canada pour fonctionner avec les types
d'antenne énumérés ci-dessous et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les
types d'antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour
l'exploitation de l'Ă©metteur.
Type d'antenne: Dipole, Gain admissible maximal: 2.5 dBi, Impédance: 50 Ohms
To satisfy RF exposure requirements, this device and its antenna must operate with a separation distance of at least 20
centimeters from all persons and must not be collocated or operating in conjunction with any other antenna or transmitter.
The specific patents that cover Crestron products are listed at patents.crestron.com.
Crestron, the Crestron logo, Cameo, Crestron Green Light, Crestron Toolbox, and infiNET EX are either
trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other
countries. Other trademarks, registered trademarks, and trade names may be used in this document to
refer to either the entities claiming the marks and names or their products. Crestron disclaims any
proprietary interest in the marks and names of others. Crestron is not responsible for errors in
typography or photography.
This document was written by the Technical Publications department at Crestron.
©2014 Crestron Electronics, Inc.
RETURN AND WARRANTY POLICIES
Merchandise Returns / Repair Service
1. No merchandise may be returned for credit, exchange or service without prior authorization from
Crestron. To obtain warranty service for Crestron products, contact an authorized Crestron dealer.
Only authorized Crestron dealers may contact the factory and request an RMA (Return
Merchandise Authorization) number. Enclose a note specifying the nature of the problem, name
and phone number of contact person, RMA number and return address.
2. Products may be returned for credit, exchange or service with a Crestron Return Merchandise
Authorization (RMA) number. Authorized returns must be shipped freight prepaid to Crestron,
6 Volvo Drive, Rockleigh, N.J. or its authorized subsidiaries, with RMA number clearly marked on
the outside of all cartons. Shipments arriving freight collect or without an RMA number shall be
subject to refusal. Crestron reserves the right in its sole and absolute discretion to charge a 15%
restocking fee plus shipping costs on any products returned with an RMA.
3. Return freight charges following repair of items under warranty shall be paid by Crestron, shipping
by standard ground carrier. In the event repairs are found to be non-warranty, return freight costs
shall be paid by the purchaser.
Crestron Limited Warranty
Crestron Electronics, Inc. warrants its products to be free from manufacturing defects in materials and
workmanship under normal use for a period of three (3) years from the date of purchase from Crestron,
with the following exceptions: disk drives and any other moving or rotating mechanical parts, pan/tilt heads
and power supplies are covered for a period of one (1) year; touch screen display and overlay components
are covered for 90 days; batteries and incandescent lamps are not covered.
This warranty extends to products purchased directly from Crestron or an authorized Crestron dealer.
Purchasers should inquire of the dealer regarding the nature and extent of the dealer's warranty, if any.
Crestron shall not be liable to honor the terms of this warranty if the product has been used in any
application other than that for which it was intended or if it has been subjected to misuse, accidental
damage, modification or improper installation procedures. Furthermore, this warranty does not cover any
product that has had the serial number altered, defaced or removed.
This warranty shall be the sole and exclusive remedy to the original purchaser. In no event shall Crestron
be liable for incidental or consequential damages of any kind (property or economic damages inclusive)
arising from the sale or use of this equipment. Crestron is not liable for any claim made by a third party or
made by the purchaser for a third party.
Crestron shall, at its option, repair or replace any product found defective, without charge for parts or
labor. Repaired or replaced equipment and parts supplied under this warranty shall be covered only by the
unexpired portion of the warranty.
Except as expressly set forth in this warranty, Crestron makes no other warranties, expressed or implied,
nor authorizes any other party to offer any warranty, including any implied warranties of merchantability or
fitness for a particular purpose. Any implied warranties that may be imposed by law are limited to the
terms of this limited warranty. This warranty statement supersedes all previous warranties.

Produktspezifikationen

Marke: Crestron
Kategorie: WLAN-Repeater
Modell: Green Light GLA-EXPEX

Brauchst du Hilfe?

Wenn Sie Hilfe mit Crestron Green Light GLA-EXPEX benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung WLAN-Repeater Crestron

Crestron

Crestron DM-TX-201-C Bedienungsanleitung

21 August 2024
Crestron

Crestron Green Light GLA-EXPEX Bedienungsanleitung

21 August 2024
Crestron

Crestron CEN-GWEXER-PWE Bedienungsanleitung

21 August 2024
Crestron

Crestron HD-TX1-F Bedienungsanleitung

21 August 2024
Crestron

Crestron HD-RX1-F Bedienungsanleitung

21 August 2024
Crestron

Crestron infiNET C2NI-MNETRPT Bedienungsanleitung

21 August 2024
Crestron

Crestron DM-TX-401-S Bedienungsanleitung

21 August 2024
Crestron

Crestron DIN-CENCN-2-POE Bedienungsanleitung

21 August 2024
Crestron

Crestron infiNET EX CEN-RFGW-EX Bedienungsanleitung

20 August 2024
Crestron

Crestron infiNET C2N-MNETRPT Bedienungsanleitung

20 August 2024

Bedienungsanleitung WLAN-Repeater

Neueste Bedienungsanleitung fĂĽr -Kategorien-

Planet

Planet WNAP-1110 Bedienungsanleitung

10 Oktober 2024
Netgear

Netgear A7000 Bedienungsanleitung

3 Oktober 2024
Planet

Planet LRP-104CET Bedienungsanleitung

30 September 2024
Netgear

Netgear WN2500RP Bedienungsanleitung

30 September 2024
Totolink

Totolink EX200U Bedienungsanleitung

29 September 2024
SilverCrest

SilverCrest SWV 300 B2 Bedienungsanleitung

29 September 2024
Xiaomi

Xiaomi RA75 Bedienungsanleitung

28 September 2024
Totolink

Totolink EX300 Bedienungsanleitung

28 September 2024
Sitecom

Sitecom WLX-2001 Bedienungsanleitung

23 September 2024
Ubiquiti Networks

Ubiquiti Networks PrismStation AC PS-5AC Bedienungsanleitung

20 September 2024