Clarion CC6300E Bedienungsanleitung

Clarion Dashcam CC6300E

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Clarion CC6300E (2 Seiten) in der Kategorie Dashcam. Dieser Bedienungsanleitung war für 30 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/2

Installation/Owner's Manual

CC-6300E

Wide Angle Compact Color CMOS Camera

 Thank you very much for your purchase of this Clarion product.

 To get the best performance from and to use this device effectively, first read this Installa-

tion/Owner’s Manual thoroughly and then install the device correctly and safely.

Clarion Co., Ltd.

SAFETY PRECAUTIONS

Always follow the safety precautions below when installing the device.

WARNING

 This device is a rear view camera intended for vehicle installation. Do not use it else-

where except when mounted on a vehicle.

If not, this may result in fuming, fire, electric shock or injury.

 Do not attempt to disassemble or modify the unit.

Never disassemble, modify or cut the cable cover to draw power from other devices. Doing so may re-

sult in accident, fire, electric shock or other malfunction.

 Do not cut the camera cable.

Moisture or water may get inside the camera through the damaged part, resulting in malfunction or fire.

 Never use the vehicle's safety-related parts* for mounting or grounding the device.

* Nuts and bolts in the steering system, seat rails, brake system, tanks, etc.

Doing so may result in loss of control, fire or traffic accident.

 Never drive while looking at the monitor screen only.

The monitor is an auxiliary equipment for checking obstacles and so on but the field of view is limited.

As the actual distance may differ from your perception, make sure you conduct a safety check visu-

ally while driving. Failure to do so may result in a person or object in the camera's blind spot to be hit,

causing a serious accident.

 Discontinue use in the event of malfunction or abnormality.

If there is no image, or when there is smoke or strange odors, stop using the camera immediately and

make sure you consult your dealer. Continued use may result in an accident, fire or electric shock.

 Do not put water or foreign objects inside the device.

In the event water or foreign objects get inside the device, and when there is smoke or strange odors,

stop using the camera immediately and make sure you consult your dealer. Continued use may result

in an accident, fire or electric shock. Make sure you consult your dealer.

 Before making connections, disconnect the negative battery terminal.

Failure to do so may result in electric shock or injury due to short-circuit.

 Keep the cables away from hot areas.

The covering of the cables may melt, causing a short-circuit and resulting in an accident or fire. Pay

particular attention to the wiring inside the engine room.

 Engage the services of a professional technician to connect and disconnect.

Failure to do so may result in an accident or fire. Contact the dealer where the device was purchased.

 After installation and wiring work, check the operation of the car's electrical compo-

nents*.

* Brakes, lights, horn, hazard lamps, blinkers, etc.

Malfunctioning equipment may lead to fire, electric shock or traffic accident.

 When drilling holes and installing the device on the vehicle side, check the positions of

the pipes, tanks, electrical wiring etc. to make sure there is no interference or contact.

Damage to the pipes etc. may lead to fire or malfunction.

 Lay and consolidate the cables so that they do not obstruct the operations.

When the cables are wrapped around the steering wheel, shift lever, brake pedal etc., this may result in

accidents.

 Reverse the car at a slow speed.

The image on the rear monitor uses a wide angle lens. As the actual distance differs from your percep-

tion, reversing at a high speed may risk collision with people and objects, resulting in a serious acci-

dent.

CAUTION

 This device is a vehicle-mounted rear view camera. Do not use the device underwater

Doing so may result in smoke, fire, electric shock or injury.

 After installation, do not hit or subject this device to strong impacts.

The mounting angle of the camera may change, or the screen may not appear normally. Malfunctions

and damages may also result from the impacts, causing fire and electric shock. Do not subject the

camera to strong impacts as it is a precision machine. Malfunctions and damages may occur, resulting

in fire and electric shock.

 Inspect the installation screws occasionally and tighten them if they are loose.

If the screws are loose, the device may become detached and fall off, hitting a passer-by and causing

an accident.

 Follow the instructions in the manual when mounting and connecting the device.

Incorrect connection may result in fire or accident.

 Be sure to use the accessories and specified parts.

Using components other than those specified may lead to damage of the parts inside the device or the

inability to secure them firmly, resulting in them becoming detached and leading to an accident or mal-

function.

 After wiring the various cords, secure them with clamps and/or insulating tape.

If the cables come into contact with the vehicle side, they will fray and short-circuit, leading to an ac-

cident or fire.

CAUTION

 Use protective tubing or insulating grommet when making a hole in the vehicle side to

route the cables.

If the cables come into contact with the openings, they will fray and short-circuit, leading to an accident

or fire.

 If a hole is made in the vehicle side to mount the device or route the cables, seal the

gap in the hole and the gap between the hole and the cable with silicon adhesive or

something similar.

If exhaust gas or water gets inside the vehicle through the gap, it may result in an accident.

 Route the cables so that they do not get caught in the vehicle side, screws, seat rails or

other moving parts.

Damaged or short-circuited cables may result in an accident, electric shock or fire.

 When mounting the camera outside the car, make sure it is mounted within the range

stipulated under the law.

 If the screws in the vehicle side are used to mount the device, be sure to tighten them

securely.

Loose screws may result in an accident or malfunction.

PRECAUTION

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a resi-

dential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to radio communica-

tions. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to consult the dealer or

an experienced radio/ TV technician for help.

INFORMATION FOR USERS:

CHANGES OR MODIFICATIONS TO THIS PRODUCT NOT APPROVED BY THE MANUFACTUR-

ER WILL VOID THE WARRANTY AND WILL VIOLATE FCC APPROVAL.

PACKAGE CONTENTS

This device consists of the following components.

In the event of any defect, contact the retailer where it was purchased.

1 Main camera unit 1 ...................................................................................................................

2 Installation/Owner’s Manual ................................................................................................... 1

Accessory bag 1 ��

3 Mounting bracket ................................................................................................................... 1

4 Hexagon head bolts with built-in washer (M3 mm x 6 mm)

(for installing on the main unit) 2 ................................................................................................

5 Hexagon head bolts with built-in washer (M3 mm x 15 mm)

(for installing on the vehicle side) 2 ............................................................................................

6 Flanged nuts (M3 mm) (for installing on the vehicle side) 2 .........................................................

7 Grommet ............................................................................................................................... 1

SPECIFICATIONS

 Power Supply Voltage : DC5V - 9.5V

 Current Consumption : 100mA or less

 Image : True image

 Image Sensor : 1/3.6 inch color CMOS

 Image Angle : Horizontal approx. 162°/ Vertical approx. 131°

 S/N Ratio : 36dB & above (AGC-ON)

 Weight : 72g (0.16lbs) (including the cable and mounting bracket)

 External Dimensions of Main Unit : 23.4mm (W) x 23.4mm (H) x 23.5mm (D)

59/64” (W) x 59/64” (H) x 59/64” (D)

 Cable Length : 0.5 m (1.64 ft)

23.4 mm

23.5 mm

36.5 mm

Declaration of conformity

We Clarion declares that the product CC-6300 is following the provisions of Directive

2014/30/EU and Directive 2011/65/EU.

Authorized Representative

Clarion Europe S.A.S.

244 rue du Pré à Varois, 54670 Custines, France

TEL +33 3 83 49 44 00 FAX +33 3 83 24 17 62

Printed in Japan 2016/7

CC6300E 274-0614-01

HOW TO INSTALL

Installation Precautions



Never swing the camera by the cable or pull the cable. Doing so may impair the cam-

era's waterprooﬁ ng or break the cable, resulting in malfunction



Avoid mounting the camera in places where the lens surface is easily stained by mud or

emission gases etc.



When the branches of roadside trees hit the camera when driving, the mounting angle

of the camera may change and the screen may not appear normally. Therefore p2-we

ommend installing a strong protective cover around the camera without obstructing the

ﬁ eld of view of the camera so that the branches of roadside trees do not hit the camera

directly.

Installation Precautions

Drill two installation holes of diameter 3�5 mm in the vehicle side�

To prevent camera shake, drill a hole in an area strong enough to mount the camera. If the part is not strong enough, carry

out appropriate reinforcement.

Use the enclosed screws and flange nuts to firmly secure the mounting bracket to the

vehicle side� (2 locations)

Secure the main camera unit to the enclosed mounting bracket� (1 location on the left and

right each)

Never install only the left or right side of the mounting bracket.

Pitch dimension of installation holes = 10 mm - 24 mm

1 Main camera unit

3 Mounting brackets

Hexagon head bolts with

built-in washer (M3 mm x

6 mm)

4 Hexagon head bolts

with built-in washer

(M3 mm x 6 mm)

6 Flanged nuts (M3 mm)

Vehicle side

Vehicle side: 3.5 mm hole

5 Hexagon head bolts with built-in

washer (M3 mm x 15 mm)

See the wiring instructions on how to lay the cables�

After connecting the cables, adjust the mounting angle of the camera� (Mounting angle on

a vertical surface is approx� 40 degrees in general�)

After adjusting the camera mounting angle, fully tighten the screws that have been

secured temporarily to secure the main camera unit�

Make sure you apply sealing material (sealant etc�) around the installation holes for

mounting the mounting bracket to the vehicle side, screws and car cable ducts to prevent

water ingress and rust�

 Installation Example

(15°)

40°

29.6 mm

38.9 mm

46.7 mm

41.8 mm

Slanting

installation

surface

Vertical installation surface

Installation example on a vertical surface

(mounting angle 40° to vertical line)

Installation example on a slanting surface

(mounting angle 40° to vertical line)

WIRING AND CONNECTIONS

Wiring Precautions



Disconnect the negative terminal of the battery before connect-

ing the cables. Failure to do so may result in electric shock or

injury due to short-circuit



Pass the relay cable inside the car to prevent it from getting

damaged. When you have no choice but to lay the cable outside

the car, make sure it is well secured to the vehicle side to avoid

it getting caught by branches and to prevent the cable from clattering. In addition, besides

connecting the connector securely, install it in a location that is not easily exposed to wa-

ter.



When laying each cable, as far as possible avoid hot areas such as the engine, exhaust

pipe, transmission etc., as well as rotating parts and noise sources such as the cooling

fan, alternator etc., and then cover it with a corrugated tube before securing with a clamp



Never cut the cables as each cable is a special cable with an in-built coaxial line



When baking and coating the vehicle, make sure the cables are laid only after the coating



Use a protective tube or grommet to protect the cables in

places where they can be easily cut by the cross-sectional area

of metal sheets or metallic parts with through holes. Lay the

cables without twisting or bending them excessively to avoid

damaging them as this may result in inter nal short circuits

Note that the waterprooﬁ ng will be affected when the external cov-

ering is cut.

Wiring Precautions

 Wiring Example

Special waterproof relay cable

(sold separately)

Fully fasten the connector.

Car Exterior

Car Interior

Connect the cable to the special

camera ECU box or LCD monitor.

 How to Connect the Special Waterproof Relay Cable (Sold Separately)

Align the arrow marking on the relay cable to the

{ marking on the camera cable to

insert the connector�

Pull the cable lightly to check that the connector is locked properly�

{ marking on the camera cable

Arrow marking on the relay cable

Do not pull or bend the ﬁtting or apply a load of more than 30 N on it .

The connector may be damaged if an excessive load is applied.

CLEANING THE CAMERA

 Do not use benzene, thinners or alcohols to clean the camera.

 Do not wipe the camera using a detergent mixed with polishing powder. This may result in

scratches to the camera.

 If the lens is dirty, use a soft cloth containing water to wipe it lightly. Scratches may result if

you wipe the lens hard with a dry cloth.

TROUBLESHOOTING

Please follow the following troubleshooting procedures in case of any problems.

Consult your dealer if you cannot resolve the issue on your own.

Symptom Reason Solution

No image Wiring is incomplete

or disconnected

Check wiring once again and Confirm correct connec-

tions.

A fuse is burned out. When using an independent power supply box, check

the fuse and, if burned out, replace with a new one of the

same capacity. If the fuse burns out repeatedly, consult

your dealer or nearest Clarion Service Center.

Poor image is pro-

duced

The lens is soiled. Wipe lightly with a damp soft cloth. Do not rub harshly

with dry cloths since scratches may be produced.

Sunlight or headlights

from other vehicle are

shining directly in the

camera.

The image will return to normal when the light striking the

lens is removed.

The environment is

too dark.

The image display will be poor at night or in dim light.

The image will return to normal in conditions of brighter

illumination.

The level of illumi-

nation outside the

vehicle changed too

abruptly.

• When moving from a bright to a dark location (espe-

cially from bright sunlight to shade), the image may ap-

pear excessively dark.

• When moving from a dark to a bright location (espe-

cially from shade into bright sunlight), the screen image

may appear excessively bright.

Produktspezifikationen

Marke:	Clarion
Kategorie:	Dashcam
Modell:	CC6300E

Brauchst du Hilfe?

Wenn Sie Hilfe mit Clarion CC6300E benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Dashcam Clarion

Clarion CAA-185-200 Bedienungsanleitung

15 August 2024

Clarion CC6300E Bedienungsanleitung

14 August 2024

Clarion CJ-7500E Bedienungsanleitung

14 August 2024

Clarion EG-2300E Bedienungsanleitung

14 August 2024

Clarion UG-2176A Bedienungsanleitung

13 August 2024

Clarion CC-6600E Bedienungsanleitung

11 August 2024

Clarion CJ-7600E Bedienungsanleitung

9 August 2024

Clarion CC-2000E Bedienungsanleitung

8 August 2024

Clarion CC-2003E Bedienungsanleitung

7 August 2024

Clarion CC-6500E Bedienungsanleitung

7 August 2024

Bedienungsanleitung Dashcam

Neueste Bedienungsanleitung für -Kategorien-

JVC KV-DR305W Bedienungsanleitung

16 Oktober 2024

Blaupunkt BP 3.1A Bedienungsanleitung

15 Oktober 2024

Uniden Dash View 50R Bedienungsanleitung

9 Oktober 2024

Cobra SC200 Bedienungsanleitung

4 Oktober 2024

Caliber CAM701 Bedienungsanleitung

3 Oktober 2024

Alpine KCX-C250MC Bedienungsanleitung

30 September 2024

Swann SWADS-130DCM Bedienungsanleitung

27 September 2024

Midland Bike Guardian Bedienungsanleitung

27 September 2024

Kenwood DRV-A610W Bedienungsanleitung

24 September 2024

Alpine KCX-C200B Bedienungsanleitung

22 September 2024