Clarion CC1601A Bedienungsanleitung
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Clarion CC1601A (2 Seiten) in der Kategorie Dashcam. Dieser Bedienungsanleitung war für 37 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/2
Installation/Owner's Manual
CC-1601A
Ultra Wide Angle Compact Color CCD Camera
Thank you very much for your purchase of this Clarion product.
To get the best performance from and to use this device effectively, first read this Installa-
tion/Owner’s Manual thoroughly and then install the device correctly and safely.
Clarion Co., Ltd.
All Rights Reserved. Copyright © 2014 : Clarion Co., Ltd.
SAFETY PRECAUTIONS
Always follow the safety precautions below when installing the device.
WARNING
This device is a rear view camera intended for vehicle installation. Do not use it else-
where except when mounted on a vehicle.
If not, this may result in fuming, fire, electric shock or injury.
Do not attempt to disassemble or modify the unit.
Never disassemble, modify or cut the cable cover to draw power from other devices. Doing so may re-
sult in accident, fire, electric shock or other malfunction.
Do not cut the camera cable
Moisture or water may get inside the camera through the damaged part, resulting in malfunction or fire.
Never use the vehicle's safety-related parts* for mounting or grounding the device.
* Nuts and bolts in the steering system, seat rails, brake system, tanks, etc.
Doing so may result in loss of control, fire or traffic accident.
Never drive while looking at the monitor screen only
The monitor is an auxiliary equipment for checking obstacles and so on but the field of view is limited.
As the actual distance may differ from your perception, make sure you conduct a safety check visu-
ally while driving. Failure to do so may result in a person or object in the camera's blind spot to be hit,
causing a serious accident.
Discontinue use in the event of malfunction or abnormality.
If there is no image, or when there is smoke or strange odors, stop using the camera immediately and
make sure you consult your dealer. Continued use may result in an accident, fire or electric shock.
Do not put water or foreign objects inside the device
In the event water or foreign objects get inside the device, and when there is smoke or strange odors,
stop using the camera immediately and make sure you consult your dealer. Continued use may result
in an accident, fire or electric shock. Make sure you consult your dealer.
Before making connections, disconnect the negative battery terminal.
Failure to do so may result in electric shock or injury due to short-circuit.
Keep the cables away from hot areas
The covering of the cables may melt, causing a short-circuit and resulting in an accident or fire. Pay
particular attention to the wiring inside the engine room.
Engage the services of a professional technician to connect and disconnect.
Failure to do so may result in an accident or fire. Contact the dealer where the device was purchased.
After installation and wiring work, check the operation of the car's electrical compo-
nents
* Brakes, lights, horn, hazard lamps, blinkers, etc.
Malfunctioning equipment may lead to fire, electric shock or traffic accident.
When drilling holes and installing the device on the vehicle side, check the positions of
the pipes, tanks, electrical wiring etc. to make sure there is no interference or contact.
Damage to the pipes etc. may lead to fire or malfunction.
Lay and consolidate the cables so that they do not obstruct the operations
When the cables are wrapped around the steering wheel, shift lever, brake pedal etc., this may result in
accidents.
Reverse the car at a slow speed
The image on the rear monitor uses a wide angle lens. As the actual distance differs from your percep-
tion, reversing at a high speed may risk collision with people and objects, resulting in a serious acci-
dent.
CAUTION
This device is a vehicle-mounted rear view camera. Do not use the device underwater
Doing so may result in smoke, fire, electric shock or injury.
After installation, do not hit or subject this device to strong impacts.
The mounting angle of the camera may change, or the screen may not appear normally. Malfunctions
and damages may also result from the impacts, causing fire and electric shock. Do not subject the
camera to strong impacts as it is a precision machine. Malfunctions and damages may occur, resulting
in fire and electric shock.
Inspect the installation screws occasionally and tighten them if they are loose.
If the screws are loose, the device may become detached and fall off, hitting a passer-by and causing
an accident.
Follow the instructions in the manual when mounting and connecting the device.
Incorrect connection may result in fire or accident.
After mounting the device, check that the monitor image is a mirror image (back mirror).
Incorrect setup may mean that the monitor image is not horizontally flipped, resulting in accident.
The rear view monitor image is inverted on the left and right just like your car's back
mirror.
The viewing angle may differ depending on the vehicle.
Be sure to use the accessories and specified parts.
Using components other than those specified may lead to damage of the parts inside the device or the
inability to secure them firmly, resulting in them becoming detached and leading to an accident or mal-
function.
CAUTION
After wiring the various cords, secure them with clamps and/or insulating tape.
If the cables come into contact with the vehicle side, they will fray and short-circuit, leading to an ac-
cident or fire.
Use protective tubing or insulating grommet when making a hole in the vehicle side to
route the cables.
If the cables come into contact with the openings, they will fray and short-circuit, leading to an accident
or fire.
If a hole is made in the vehicle side to mount the device or route the cables, seal the
gap in the hole and the gap between the hole and the cable with silicon adhesive or
something similar.
If exhaust gas or water gets inside the vehicle through the gap, it may result in an accident.
Route the cables so that they do not get caught in the vehicle side, screws, seat rails or
other moving parts.
Damaged or short-circuited cables may result in an accident, electric shock or fire.
When mounting the camera outside the car, make sure it is mounted within the range
stipulated under the law.
If the screws in the vehicle side are used to mount the device, be sure to tighten them
securely.
Loose screws may result in an accident or malfunction.
PRECAUTION
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a resi-
dential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communica-
tions. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to consult the dealer or
an experienced radio/ TV technician for help.
INFORMATION FOR USERS:
CHANGES OR MODIFICATIONS TO THIS PRODUCT NOT APPROVED BY THE MANUFACTUR-
ER WILL VOID THE WARRANTY AND WILL VIOLATE FCC APPROVAL.
PACKAGE CONTENTS
This device consists of the following components.
In the event of any defect, contact the retailer where it was purchased.
1 Main camera unit 1 ...................................................................................................................
2 Mounting bracket ................................................................................................................... 1
3 Installation/Owner’s Manual ................................................................................................... 1
4 Grommet ............................................................................................................................... 1
Accessory bag 1 ����������������������������������������������������������������������������������������������������������������������������������
5 Hexagon head bolts with built-in washer (M4 mm x 10 mm)
(for installing on the main unit) 4 ................................................................................................
6 M4 bush (for installing on the main unit) .................................................................................. 4
7 Hexagon head bolts with built-in washer (M5 mm x 20 mm)
(for installing on the vehicle side) 2 ............................................................................................
8 Flanged nuts (M5 mm) (for installing on the vehicle side) 2 .........................................................
SPECIFICATIONS
Power Supply Voltage : DC9.0V± 0.5V
Current Consumption : 150mA or less
Image Sensor : 1/4 inch 0.25 mega-pixel color CCD
Image Angle : Horizontal 162°/ Vertical 129.8°
S/N Ratio : 36dB & above
Weight : 145g (including the cable)
External Dimensions of Main Unit : 46(W) x 37(H) x 33.8(D) mm
46 mm
37 mm
33.8 mm
42.3 mm
Declaration of conformity
We Clarion declares that the product CC-1601 is following the provision of Directive
2004/108/EC and Directive 2011/65/EU.
Authorized Representative
Clarion Europe S.A.S.
Z.I. du Pré à Varois, Route de Pompey, 54670 Custines, France
Telephone: +33 (0)3 83 49 44 00 Fax: +33 (0)3 83 49 45 99
Printed in Japan 2014/3 CC1601A 274-0616-00
HOW TO INSTALL
Installation Precautions
Be sure to use the supplied screws to mount the
camera. If any screws are lost when mounting the
camera, be sure to use M4x10 hexagon head bolts
with built-in washer. Never use screws that are lon-
ger than this. The screws in the camera case have
a bag structure to make sure it is waterproof. Use
of long screws may damage the screw thread and
camera case, compromising the waterproofi ng
Never swing the camera by the cable or pull the ca-
ble. Doing so may impair the camera's waterproofi ng
or break the cable, resulting in malfunction
Avoid mounting the camera in places where the lens surface is easily stained by mud or
emission gases etc.
When the branches of roadside trees hit the camera when driving, the mounting angle
of the camera may change and the screen may not appear normally. Therefore p2-we
ommend installing a strong protective cover around the camera without obstructing the
fi eld of view of the camera so that the branches of roadside trees do not hit the camera
directly.
Installation Precautions
10 mm
M4 x 10 mm
Camera mounting screws
5
Hexagon head bolts with built-in
washer (M4 mm x 10 mm)
1
Drill two installation holes of diameter 5�5 mm in the vehicle side�
To prevent camera shake, drill a hole in an area strong enough to mount the camera. If the part is not strong enough, carry
out appropriate reinforcement.
2
Use the enclosed screws and flange nuts to firmly secure the mounting bracket to the
vehicle side� (2 locations)
3
Use the enclosed screws and bush to temporarily secure the main camera unit to the
mounting bracket� (2 locations on the left and right each)
Never install only the left or right side of the mounting bracket.
Pitch dimension of installation holes = 30 mm
1 Main camera unit
2 Mounting brackets
7
Hexagon head
bolts with
built-in washer
(M5 mm x 20
mm)
6 M4 bush
5 Hexagon head bolts
with built-in washer
(M4 mm x 10 mm)
8 Flanged nuts (M5 mm)
Vehicle side
Vehicle side: 5.5 mm hole
4
See the wiring instructions on how to lay the cables�
5
After connecting the cables, adjust the mounting
angle of the camera so that the rear bumper or
back end of the vehicle appears in the monitor�
(refer to the figure on the right)
6
After adjusting the camera mounting angle,
fully tighten the screws that have been secured
temporarily to secure the main camera unit�
7
Make sure you apply sealing material (sealant etc�) around the installation holes for
mounting the mounting bracket to the vehicle side, screws and car cable ducts to prevent
water ingress and rust�
Installation Example
Installation example on a horizontal surface
(mounting angle 44°)
44°
54.3 mm
60.8 mm
24 mm
24 mm
60.8 mm
54.3 mm
Vertical
installation
surface
Installation example on a vertical surface
(mounting angle 44°)
44°
Horizontal
installation
surface
WIRING AND CONNECTIONS
Wiring Precautions
Disconnect the negative terminal of the battery before connect-
ing the cables. Failure to do so may result in electric shock or
injury due to short-circuit
Pass the relay cable inside the car to prevent it from getting
damaged. When you have no choice but to lay the cable outside
the car, make sure it is well secured to the vehicle side to avoid
it getting caught by branches and to prevent the cable from clattering. In addition, besides
connecting the connector securely, install it in a location that is not easily exposed to wa-
ter.
When laying each cable, as far as possible avoid hot areas such as the engine, exhaust
pipe, transmission etc., as well as rotating parts and noise sources such as the cooling
fan, alternator etc., and then cover it with a corrugated tube before securing with a clamp
Never cut the cables as each cable is a special cable with an in-built coaxial line
When baking and coating the vehicle, make sure the cables are laid only after the coating
Use a protective tube or grommet to protect the cables in
places where they can be easily cut by the cross-sectional area
of metal sheets or metallic parts with through holes. Lay the
cables without twisting or bending them excessively to avoid
damaging them as this may result in inter nal short circuits
Note that the waterproofi ng will be affected when the external cov
ering is cut.
Wiring Precautions
Wiring Example
Special waterproof relay cable
(sold separately)
Fully fasten the connector.
Car Exterior
Car Interior
Connect the cable to the LCD monitor
or CCD camera power box.
How to Connect the Special Waterproof Relay Cable (Sold Separately)
When tightening the cable nut, make sure you use two spanners (for 17 mm nuts) on the me-
tallic nuts of both connectors and follow the procedure below to tighten the nuts.
Secure the plastic parts with a plier etc. and never fasten them. This may result in infi ltration
by rainwater and malfunction due to damage to the plastic part of the connector.
1
Align the "]" marking on each connector
and turn the nut with your hand to tighten
it until it stops�
2
Set a spanner (for 17 mm nuts) to the nut
of each cable from the hand tightening
position and turn the nut on the camera
side about half a turn (180°)� (Secure the
relay cable side so that it does not rotate
when doing so�)
Recommended torque: approx. 2.45 N·m
CLEANING THE CAMERA
Do not use benzene, thinners or alcohols to clean the camera.
Do not wipe the camera using a detergent mixed with polishing powder. This may result in
scratches to the camera.
If the lens is dirty, use a soft cloth containing water to wipe it lightly. Scratches may result if
you wipe the lens hard with a dry cloth.
TROUBLESHOOTING
Please follow the following troubleshooting procedures in case of any problems.
Consult your dealer if you cannot resolve the issue on your own.
Symptom Reason Solution
No image Wiring is incomplete or
disconnected
Check wiring once again and Confirm correct connections.
A fuse is burned out. When using an independent power supply box, check the fuse and,
if burned out, replace with A new one of the same capacity (1 A). If
the fuse burns out repeatedly, consult your dealer or nearest Clarion
Service Center.
Poor image is produced The lens is soiled. Wipe lightly with a damp soft cloth. Do not rub harshly with dry cloths
since scratches may be produced.
Sunlight or headlights
from a vehicle in the rear
are shining directly in the
camera.
The image will return to normal when the light striking the lens is
removed.
The environment is too
dark.
The image display will be poor at night or in dim light. The image will
return to normal in conditions of brighter illumination.
The level of illumina-
tion outside the vehicle
changed too abruptly.
• When moving from a bright to a dark location (espe-
cially from bright sunlight to shade), the image may ap-
pear excessively dark.
• When moving from a dark to a bright location (espe-
cially from shade into bright sunlight), the screen image
may appear excessively bright.
Monitor screen
Rear bumper or
rear end of
the vehicle
approx. 7 mm
Turn the nut
on the camera side 180°
Cable on the
camera side
Relay cable
Relay cable side
Secure the nut
with a spanner
Produktspezifikationen
| Marke: | Clarion |
| Kategorie: | Dashcam |
| Modell: | CC1601A |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Clarion CC1601A benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Dashcam Clarion
15 August 2024
14 August 2024
14 August 2024
14 August 2024
13 August 2024
11 August 2024
9 August 2024
8 August 2024
7 August 2024
7 August 2024
Bedienungsanleitung Dashcam
- Dashcam Gembird
- Dashcam Genius
- Dashcam Hama
- Dashcam HP
- Dashcam Nedis
- Dashcam Niceboy
- Dashcam Philips
- Dashcam AEG
- Dashcam Dymond
- Dashcam Maginon
- Dashcam Technaxx
- Dashcam Denver
- Dashcam König
- Dashcam Trevi
- Dashcam Blaupunkt
- Dashcam Kenwood
- Dashcam Trebs
- Dashcam Dometic
- Dashcam Pyle
- Dashcam Salora
- Dashcam Aiptek
- Dashcam Caliber
- Dashcam Pioneer
- Dashcam JVC
- Dashcam Motorola
- Dashcam Xiaomi
- Dashcam Elro
- Dashcam Ferguson
- Dashcam Garmin
- Dashcam GOCLEVER
- Dashcam Lamax
- Dashcam Mio
- Dashcam Sencor
- Dashcam Waeco
- Dashcam Scosche
- Dashcam XOMAX
- Dashcam Guardo
- Dashcam Midland
- Dashcam Alpine
- Dashcam Minolta
- Dashcam Rollei
- Dashcam EUFAB
- Dashcam Pro User
- Dashcam Toyota
- Dashcam ADATA
- Dashcam Overmax
- Dashcam Monacor
- Dashcam Ednet
- Dashcam Osram
- Dashcam NextBase
- Dashcam Uniden
- Dashcam Kogan
- Dashcam Jobo
- Dashcam Skytronic
- Dashcam Audiovox
- Dashcam Navitel
- Dashcam Navman
- Dashcam Cobra
- Dashcam CamOne
- Dashcam EVOLVEO
- Dashcam TrueCam
- Dashcam ION
- Dashcam DNT
- Dashcam Swann
- Dashcam Xblitz
- Dashcam Prestigio
- Dashcam Tracer
- Dashcam Boss
- Dashcam Mini
- Dashcam Hertz
- Dashcam Hikvision
- Dashcam Jensen
- Dashcam Transcend
- Dashcam DOD
- Dashcam Innovv
- Dashcam IRoad
- Dashcam Laser
- Dashcam Lidl
- Dashcam Media-tech
- Dashcam Naxa
- Dashcam Nordval
- Dashcam Roadeyes
- Dashcam Steren
- Dashcam Thinkware
- Dashcam Veho
- Dashcam NAV-TV
- Dashcam Metra
- Dashcam ModeCom
- Dashcam CRUX
- Dashcam Escort
- Dashcam Brigmton
- Dashcam Kaiser Baas
- Dashcam KJB Security Products
- Dashcam BlackVue
- Dashcam Valueline
- Dashcam Braun Phototechnik
- Dashcam BLOW
- Dashcam Boyo
- Dashcam Cowon
- Dashcam Rexing
- Dashcam Dashmate
- Dashcam EchoMaster
- Dashcam AZDome
- Dashcam Carmera
- Dashcam VIOFO
- Dashcam Mobileye
- Dashcam Kapture
- Dashcam ProUser
- Dashcam Nanocam+
- Dashcam Vicovation
- Dashcam Andatech
- Dashcam RIPOON
Neueste Bedienungsanleitung für -Kategorien-
16 Oktober 2024
15 Oktober 2024
9 Oktober 2024
4 Oktober 2024
3 Oktober 2024
30 September 2024
27 September 2024
27 September 2024
24 September 2024
22 September 2024