Chamberlain CWPIR Bedienungsanleitung

Chamberlain Bewegungsmelder CWPIR

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Chamberlain CWPIR (2 Seiten) in der Kategorie Bewegungsmelder. Dieser Bedienungsanleitung war für 9 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/2
1
Carton Inventory
Assembly & Programming
Attach PIR Motion Sensor box
to mounting plate with large
silver screw. Tighten screw
until PIR Motion Sensor stays
in place when repositioned.
Passive Infra-Red (PIR)
Motion Sensor
Swivel Bushing
Mounting PlateSun/Rain Shield
1
Install 4 AA Alkaline
batteries. (Lithium batteries
recommended for colder
environments.)
LED light will fl ash.
2
Antenna
ON
OFF
1 2
SWITCH SETTINGS
Switch #1 Switch #2
Learn
Button
OFF Low Sensitivity
ON High Sensitivity (Default)
OFF 15 Feet (4.5 m) Detection Range
ON 30 Feet (9.1 m) Detection Range
(Default)
NOTE: To avoid unwanted detection of small animals move
Switch #2 to OFF.
PIR Motion Sensor
SWITCH #1:
SWITCH #2:
A Ensure Base Station and PIR
Motion Sensor are in close
proximity to each other.
Press and release Learn
Button on Base Station.
Buzzer will sound.
B Within 60 seconds, press the
Learn Button on the inside of
the PIR Motion Sensor. LED
light will illuminate and Base
Station will buzz.
3Learn Button
Test PIR Motion Sensor by
waving hand in front of sensor.
LED light should fl ash and
the Base Station will buzz X
number of times indicating
which sensor has been
activated.
Insert battery pack facing away
from circuit board and fasten
cover with the smallest screws
(provided).
NOTE: Ensure the batteries do
not touch the circuit board and
the antenna and battery wires
are not pinched.
4
5
Overview
Learn Button
Models CWPIR and CWPIRC
WIRELESS MOTION ALERT SENSOR
®
The Wireless Alert Sensor is a Passive Infra-Red (PIR) Motion Sensor that detects movement of people and vehicles, while allowing
small animals to pass through undetected. Each sensor has its own unique ID, for a secure radio link. The base station (not provided)
can learn the signals of up to 8 sensors. The base station gives a single beep for the fi rst sensor that is programmed, a double beep for
the second, and so on. Additionally, multiple base stations can work with the same sensor to sound in different places.
Assembly & Programming
PIR MOTION SENSOR INSTALLATION
Mount PIR Motion Sensor
horizontally on solid surface
3-5 feet (1-1.5 m) off the
ground and within 1/2 mile
(0.8 km) of Base Station (rotate
sensor to access screw holes).
Unit should be able to swivel as
needed.
Attach sun/rain shield.
NOTE: Keep PIR Motion
Sensor antenna away from
metal objects. Do not mount
PIR Motion Sensor in direct
sunlight, near moving tree
branches, or in the path of a
sprinkler system.
4 feet (1.2 m)
10-20 feet (3-6 m)
Vehicle Alert Installation: For cars, the best mounting position
is about 4 feet (1.2 m) high, between 10-20 feet (3-6 m)back,
and angled to see the back of car after passing the sensor.
6
Troubleshooting
The PIR Motion Sensor lights up, but the Base Station does
not respond.
The PIR Motion Sensor must be programmed to Base Station
(See Step 3). Ensure Base Station is on and the volume is
turned up.
PIR Motion Sensor is detecting motion only part of the time.
Ensure the PIR Motion Sensor is set to the High Sensitivity
setting (See Step 2). To detect cars, it is best to mount PIR
Motion Sensor at height of car’s motor and have it between
10-20 feet (3-6 m) from the road. Swivel sensor as needed.
The Alert is giving false alarms.
Check for moving tree branches or insects in sensor window.
PIR Motion Sensor can also be triggered by light shining
directly in sensor window, such as refl ected sunlight, or motion
in front of a light source.
It is possible that condensation has built up on the sensor. Wipe
condensation from PIR Motion Sensor with cotton swab. Let it
sit inside for a few hours, open to the air, without the batteries
and it should correct itself.
Check Sensor Switches on PIR Motion Sensor. See Switch
Settings.
Base Station beeps every 30 minutes.
The batteries in the Base Station or the PIR Motion Sensor(s)
are low. Replace the 4 AA batteries. Check the PIR Motion
Sensor(s), if the LED illuminates on all of the PIR Motion
Sensors, change the batteries in the Base Station.
The Alert is not getting expected transmission range.
Keep both antennas vertical and keep PIR Motion Sensor
antenna away from trees and metal objects. Ensure Base Station
is in clearest possible sight of the PIR Motion Sensor. The less
objects between the devices, the longer the range.
NOTE: The manufacturer is not responsible for any radio or
TV interference caused by unauthorized modifi cations to this
equipment. Changes or modifi cations not expressly approved
by the manufacturer could void the user’s authority to operate
the equipment.
NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment or modifications of this
receiver and/or transmitter are prohibited, except for changing the code setting or replacing the
battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.
FOR TECHNICAL SUPPORT DIAL OUR TOLL FREE NUMBER:
1-800-528-9131
www.chamberlain-DIY.com
© 2010, The Chamberlain Group Inc.
114A3897D All Rights Reserved

Produktspezifikationen

Marke: Chamberlain
Kategorie: Bewegungsmelder
Modell: CWPIR

Brauchst du Hilfe?

Wenn Sie Hilfe mit Chamberlain CWPIR benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Bewegungsmelder Chamberlain

Chamberlain

Chamberlain CWA2000C Bedienungsanleitung

31 Juli 2024
Chamberlain

Chamberlain CWPIRC Bedienungsanleitung

29 Juli 2024
Chamberlain

Chamberlain CWPIR Bedienungsanleitung

25 Juli 2024
Chamberlain

Chamberlain CWA2000 Bedienungsanleitung

7 Juli 2024

Bedienungsanleitung Bewegungsmelder

Neueste Bedienungsanleitung für -Kategorien-

Orbis

Orbis Circumat Bedienungsanleitung

10 Oktober 2024
Vemer

Vemer Sensor 360L Bedienungsanleitung

6 Oktober 2024
Perel

Perel EMS103 Bedienungsanleitung

3 Oktober 2024
Renkforce

Renkforce 1362921 Bedienungsanleitung

27 September 2024
Busch-Jaeger

Busch-Jaeger Sicherheitstechnik 6800-0-2521 Bedienungsanleitung

17 September 2024
Busch-Jaeger

Busch-Jaeger 2CKA006200A0056 Bedienungsanleitung

15 September 2024
DSC

DSC PG9862 Bedienungsanleitung

14 September 2024
Maxsa

Maxsa 40234 Bedienungsanleitung

11 September 2024
Maxsa

Maxsa 43218 Bedienungsanleitung

11 September 2024
ORNO

ORNO OR-CR-233 Bedienungsanleitung

10 September 2024