BeamZ S2000 160.500 Bedienungsanleitung

BeamZ Messer S2000 160.500

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für BeamZ S2000 160.500 (16 Seiten) in der Kategorie Messer. Dieser Bedienungsanleitung war für 9 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/16

S2000 Smokemachine DMX LED 24 x 3W

Ref. nr.: 160.500

INSTRUCTION MANUAL

GEBRUIKSAANWIJZING

GEBRAUCHSANLEITUNG

NOTICE D’UTIILSATION

V2.1

ENGLISH

Warning:

- The fog machine must be placed at least 100 cm away from inﬂammable materials such as curtains, books, etc. Make sure

that the housing cannot be touched by accident.

- Use only Beamz water-based ﬂuid recommended by your dealer.

- Poor liquid caused permanent damage, bad eﬀect, clogging, spitting of unevaporated liquid etc.

- Never add ﬂammable ﬂuids (oil, gas, perfume) to the fog liquid.

- Always keep enough liquid in the tank.

Use of the device without liquid will cause damage to the pump and heater.

- Do not obstruct the openings on top of the case to guarantee a good ventilation.

- objects on the fog machine Don’t put any .

- For indoor use only.

- During installation, nobody should stand beneath the mounting area.

- Prior to the ﬁrst use, have the unit checked by a qualiﬁed person.

- The unit contains voltage carrying parts. DO NOT open the fog machine.

- Never plug or unplug the unit with wet hands.

- If the plug and/or mains lead are damaged, they need to be repaired by a qualiﬁed technician.

- If the unit is damaged to an extent that you can see internal parts, do not plug the unit into a mains outlet. It needs to be

repaired by a qualiﬁed technician.

- Only connect this unit to an earthed mains outlet of 220-240Vac/50Hz .

- Always unplug the unit during a thunderstorm or when it is not in use.

- If the unit has not been used for a longer period of time, condensation can occur inside the housing. Please let the unit reach

room temperature prior to use.

- When you unplug the unit from the mains always pull the plug, never the lead.

- In order to prevent dropping of the unit, a safety fastening needs to be installed. This can be a solid chain, a steel cable, etc.

which has to be fastened separately from the mounting bracket.

- The supplied bracket is the main ﬁxing and must be used to solidly mount the light eﬀect.

- In order to avoid accidents in public premises, the local legal requirements and safety regulations/warnings must be fulﬁlled.

- Keep out of the reach of children.

Location

Select a location where it is easy to ﬁll the tank.

INSTALLATION AND USE

Safety

Plug the fog machine only in an earthed mains outlet or extension cord! ATTENTION: the powercord can only be replaced by an

original replacement, supplied by Tronios. Be careful when ﬁlling the ﬂuid tank. First of all, unplug the mains lead! Then unscrew

the cap on the tank and ﬁll it by means of a funnel.

Only use the original Beamz ﬂuid which is environmental friendly and, if used correctly, leaves no residues.

Do not obstruct the openings on top of the case to guarantee a good ventilation. The heating element of the smoke machine

generates heat which needs to be removed. Don’t put any objects on the smoke machine.

How to use

Unpack the f machine. Do not connect yet the net cable. Fill the ﬂuid tank by means of a funnel. Plug the unit into a mains og

outlet. Thus the heating element is automatically switched on. Depending on the room temperature, it takes about 3 minutes

until the working temperature is reached. Then the thermostat is clicking and the LED on the manual control lights up. Push the

switch once and the f machine will produce a nice thick fog. Once the f machine has reached its working temperature (the og og

LED is lit) the f machine can produce fog continuously. After this period of time, the fog generator is cooled so much down og

that the thermostat switches oﬀ. Wait a while until the working temperature is reached again. It is recommended to produce

haze with small pauses in between so that the temperature is maintained and the thermostat doesn’t switch off.

Make sure that there is always enough liquid contained in the tank. Use of the f machi without liquid can permanently og ne

damage the unit. Once the f machine generates little haze or pump generate another 'rattling' sound turn oﬀ the unit direct. og

Check the ﬂuid level and ﬁll the tank when it is empty, check the hose and ﬁlter blockages and restore it. Plug in the unit and

check if the problem is resolved. If problem persists, switch unit direct oﬀ to prevent further damage and contact your dealer.

Switching the unit oﬀ

Switch the unit oﬀ by unplugging it from the mains. Otherwise the heating element will draw unnecessarily current.

Remote control:

SETTINGS

Via the Menu key, you can adjust the desired settings. After pressing the menu, the display shows the following settings:

1. Man Vol Out xxx%.

Adjust the manual volume output within the range of 0% to 100% by means of the Up/Down keys.

2. Interval Set xxxS

Adjust the interval between each fog emission within the range of 1 to 100S by means of the Up-/Down keys.

3. Duration Set xxxS

Adjust the duration of each fog emission within the range of 1 to 100S.

4. Volume Out xxx%

Adjust the volume output during the timer function within the range of 0- 100%

5. DMX 512 #xxx

Adjust the DMX address for DMX control.

6. Wind For Class xx

NO FUNCTION for this smoke machine

7. Angel Set xx%

NO FUNCTION for this smoke machine

8. LED Pro Set xx

Adjust the LED program within the range of 0 to 11.

9. LED Spe xxx

Adjust the LED speed/strobe/fade of the LED program mode

10. Temper Max:xxx

Adjust the maximum heating temperature of the heating element, adjustable between 285° - 330°C.

11. LED Sync Set Yes/No

Adjust the LED mode. Yes=LEDs work together with the smoke output, NO=LEDs are always on.

12. Temper Min:xxx

Adjust the minimum heating temperature of the heating element, adjustable between 260° - 310°C.

TIMER CONTROL

Press the Timer key to activate the timer function. The display shows the adjusted interval and the device counts the seconds

down to "0". After that, the fog emission is triggered at the volume adjusted under "Timer Out". The duration depends on the

settings adjusted under "Duration Set". If you wish to deactivate the timer function, press the Timer key once more.

Manual control (100% output)

Press the Manual key for immediate triggering of the fog emission at 100 % volume. Let the Manual key

loose in order to stop the fog emission.

Manual control (locked)

Press the Lock switch for immediate triggering of the fog emission at the volume adjusted under "Volume Out". Press the

Volume switch once more in order to stop the fog emission.

DMX control

Connect the machine directly to a DMX controller or a DMX loop with multiple DMX eﬀects. The machine uses a 3-pin XLR

connector for DMX connection.

Address Setup: Press the MODE button a number of times until Add appears on the display, with the UP / DOWN buttons the

start address may be set. The start address is deﬁned as a ﬁrst channel to which the machine will respond to. Check that there

are no overlapping channels used!

Produktspezifikationen

Marke:	BeamZ
Kategorie:	Messer
Modell:	S2000 160.500
Gewicht:	7900 g
Produktfarbe:	Grau
AC Eingangsspannung:	220-240 V
AC Eingangsfrequenz:	50 Hz
Leistung:	2000 W
Kabellänge:	4 m
Fernbedienung:	Ja
Fernbedienungstyp:	Kabelgebunden
Kapazität Flüssigkeitstank:	2.5 l
Anwärmdauer:	4 min
Abmessungen Gerät (B x H x T):	450 x 310 x 210 mm
Arbeitende Flüssigkeit:	Wasser
Rauch output volumen:	530 m³/min