Atdec TH-PPA-2448 Bedienungsanleitung

Atdec Unterstützung für Flachbildschirme TH-PPA-2448

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Atdec TH-PPA-2448 (5 Seiten) in der Kategorie Unterstützung für Flachbildschirme. Dieser Bedienungsanleitung war für 14 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/5
M2.5x15mm w/ Washer
M3x15/20mm w/ Washer
TH-PF
Component Checklist
Pro AV Projector Ceiling Mount
Square Nut (x4)
Leg (x4)
Coach Bolt (x4)
Nylon
Anchor (x4)
HARDWARE Projector Mounting Screws (x4 each)
M4x15/20/25mm
M5x15/20/25mm
M6x15/20/25mm
Tools Required:
• Power Drill
• 4mm(0.15”) Drill Bit
• 9mm(0.35”) Masonry Drill Bit
• Phillips Head Screwdriver
• 13mm (0.5”) Socket Wrench/ Shifter
! IMPORTANT - Install Telehook Projector Ceiling Mount as per installation instruction.
! This product supports a maximum load of 25kg (55lbs.).
! The manufacturer accepts no responsibility for incorrect installation.
IMPORTANT INFORMATION:
Step 1. Check Components
Check you have received against the component checklist and hardware above.
M6 Washer (x4)
Mount
Step 2. Cable Management
Step 4. Ceiling Mount
Base Plate
10mm Spacer
(x4 each)
M5x10mm Socket
Head Screw (x4)
M5x10mm
Security Screw
3mm Security
Allen Key
Security Cap (x4)
The TH-PF can be mounted flush to a ceiling (Step 4) or to a pole (Step 5).
Before mounting your TH-PF, give consideration to your cable route. The
TH-PF has provision for cable management as shown below.
Step 3. Choosing Orientation
Ensure the Mount is attached with the Projector Marks pointing in the same
direction that the projector will be facing.
Projector Mark
Projector Mark
IMPORTANT! Any structural elements must be capable of supporting the combined weight of
all the equipment and devices being mounted. If in doubt, consult a structural engineer.
Timber Stud Masonry
Coach Bolt
M6 Washer
Mount
TIP: Use Mount as a drilling template.
Coach Bolt
M6 Washer
Mount
Ø9mm x 40mm deep
Drilled Hole
Ø4mm x 35mm deep
Drilled Hole
Installation Instructions
Step 5. Pole Mount
Note: The TH-PF is compatible with 1.5NPT thread.
A range of Pole Accessories are available from Atdec.
1. Install Pole Accessory.
2. Thread mount fully into the end of the Pole.
3. Set the orientation by unwinding the mount. Do
not unwind the mount more than one full turn.
4. Lock the mount in place by tightening the two
security set screws in place using the supplied
security allen key.
Pole Accessory
(Purchased separately
or as part of a kit
from Atdec)
2 MOUNT
4 TIGHTEN
4 TIGHTEN
Step 7. Attach the Legs to the Projector
Leg
Spacer
(optional)
Projector
Projector Mounting
Screw
Note: Washers must be used in conjunction with M2.5 and M3 projector mounting screws.
FOUR FIXING POINTS THREE FIXING POINTS
OR
Step 6. Mounting Projector
Depending on the size of your projector, the
TH-PF has several mounting options available.
Smaller Projectors can be mounted directly to
the Base Plate.
For all other projectors, use the supplied legs.
Projector Mounting
Screw
Base Plate
Projector
Spacer (optional)
Projector Mounting
Screw
Leg
Spacer (optional)
Projector
Washer (optional)
Washer (optional)
Step 8. Height Adjustment
Step 9. Insert Security Caps Step 10. Insert Square Nuts
Security Cap
Insert Security Cap and tighten using the supplied 3mm Security Allen Key.
INSERT
Square Nut
Insert one Square Nut to each leg.
Note: if a difference in height of over 7mm is present use the
spacers provided
+ HEIGHT
- HEIGHT
Rotate the dial of the Leg counter-clockwise to increase height and
clockwise to decrease height.
If the surface of the projector is uneven the height of the legs can
be adjusted to allow the legs to level with each other by turning
the dial on the leg.
7mm Max.
Studs
1. The four studs on the Base Plate should point along the axis
of the projector.
2. Position the Base Plate centrally towards the heaviest part of
the projector so that the weight of the projector is centred and
balanced after mounting.
Step 11. Base Plate Orientation Step 12. Attach Base Plate
Use the supplied 3mm Security Allen Key to tighten the four screws.
Base Plate
M5x10mm Socket
Head Screw
Square Nut
(inside the Leg)

Produktspezifikationen

Marke: Atdec
Kategorie: Unterstützung für Flachbildschirme
Modell: TH-PPA-2448

Brauchst du Hilfe?

Wenn Sie Hilfe mit Atdec TH-PPA-2448 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Unterstützung für Flachbildschirme Atdec

Atdec

Atdec TH-30-50-RW Bedienungsanleitung

21 August 2024
Atdec

Atdec TH-3070-CTW Bedienungsanleitung

21 August 2024
Atdec

Atdec L-PB Bedienungsanleitung

20 August 2024
Atdec

Atdec SD-DP-750 Bedienungsanleitung

20 August 2024
Atdec

Atdec VF-AT-D Bedienungsanleitung

20 August 2024
Atdec

Atdec AF-AT-D Bedienungsanleitung

20 August 2024
Atdec

Atdec VFS-DH/TAA Bedienungsanleitung

20 August 2024
Atdec

Atdec SD-DO-42-BK Bedienungsanleitung

20 August 2024
Atdec

Atdec TH-PS-D Bedienungsanleitung

20 August 2024
Atdec

Atdec TH-PPA-2448 Bedienungsanleitung

19 August 2024

Bedienungsanleitung Unterstützung für Flachbildschirme

Neueste Bedienungsanleitung für -Kategorien-

NEC

NEC PDVWXUN 55 P Bedienungsanleitung

16 Oktober 2024
Insignia

Insignia NS-STV3N1705 Bedienungsanleitung

15 Oktober 2024
Abus

Abus BW8060 Bedienungsanleitung

4 Oktober 2024
One For All

One For All DM 4110 Bedienungsanleitung

2 Oktober 2024
One For All

One For All DM 7220 Bedienungsanleitung

2 Oktober 2024
One For All

One For All DM 2220 Bedienungsanleitung

2 Oktober 2024
Kogan

Kogan KASMM39S12A Bedienungsanleitung

1 Oktober 2024
Kogan

Kogan KATWM70TLMA Bedienungsanleitung

1 Oktober 2024
Kogan

Kogan KADMM46G24A Bedienungsanleitung

1 Oktober 2024
Kogan

Kogan KADMMPCGASC Bedienungsanleitung

1 Oktober 2024