Atdec TH-CM-SH-2 Bedienungsanleitung

Atdec Unterstützung für Flachbildschirme TH-CM-SH-2

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Atdec TH-CM-SH-2 (2 Seiten) in der Kategorie Unterstützung für Flachbildschirme. Dieser Bedienungsanleitung war für 9 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/2
Shelf (x2)
TM
Component Checklist
Installation Instructions
TELEHOOK
Cable Manager Shelf System
Bits Bag
A Installation Options
M4 x 5mm Grub
Screw (x8)
2mm Allen Key
Check you have received
all parts against the
Component Checklist
If you already have the
Telehook Cable Manager
installed.
Begin by removing the Front Fascia and
the End Caps as shown. Once
complete, continue to step B below.
Option 1
If you are installing both
the Telehook Cable Manager and Telehook Cable
Manager Shelf System at the same time.
Begin by mounting the Wall Plate as shown in step A on the
Telehook Cable Manager Installation Instructions. Once complete,
continue to step B below.
Option 2
If your display is already wall mounted, depending on its position, it may be best to remove the display,
as it may interfere with the installation of the Telehook Cable Manager and Cable Manager Shelf System.
B Installing Telehook Cable Manager Shelves
Push one edge of the
Front Fascia until it
pops open
B.1.
Slide the Cable Manager Shelf
onto the Cable Manager Wall
Mount
Adjust the Cable Manager
Shelf to the
desired height
B.2.
Secure in place using the M4 Grub Screws and
the 2mm Allen Key supplied
B.3.
Remove End
Caps
Note:
If the mounted height of the display is
less than the length of the Telehook
Cable Manager, you may need to reduce
the length by cutting it to size.
(Consult a professional at this stage)
TOP VIEW
The Telehook Cable Manager Shelf System MUST be used in
conjunction with the Telehook Cable Manager.
Each Telehook Cable Manager is limited to a maximum of 4 Shelves.
Each Shelf supports a maximum weight of 20kgs (44lbs).
If you wish to paint your Cable Manager Shelves, please consult your
paint specialist for advice.
IMPORTANT NOTES
OR
Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published: 24.09.07©
C Install your Equipment
Install or reinstall your display
Place your Audio/Video equipment on the Telehook Cable Manager Shelves
Connect all required cables to Audio/Video equipment
D Installing Cables
Display on
wall mount
bracket
Wall Plate
Install the display’s cables into the left,
right and centre cable bays as shown
E Insert Cable Clips
Cable
Tab
F Attach End Caps
TOP VIEW
Attach an End Cap onto
both ends of the Wall
Plate and secure in place
using the M4 Grub
Screws as shown.
NOTE:
If possible, separate the display’s
power cable from the data cables
(i.e. hi-fi & speaker cables) by
installing them into separate cable
bays. This will reduce the chance of
electromagnetic interference. The
diagram to the right shows an
example installation setup.
Left cable bay
Centre cable bay
(best for display power cable)
Right cable bay
Data cables
(can also be installed
into the same bay)
TOP VIEW
Using two hands,
flex the End Cap
around the
display’s cables
and manoeuvre
them into their
corresponding End
Cap Cable Bay
End Cap Cable Bay
E.2.
Twist the Cable
Tabs into the small
slots in the Wall
Plate
Display Power
cable
2mm
Allen
Key
M4
Grub
Screw
WARNING: DO
NOT OVER TIGHTEN
G Insert Front Fascia
G.2.
Partially insert the front
fascia as shown above
TOP VIEW
G.3.
Push the edge of the
Front Fascia until it
snaps into place
G.4.
Repeat G.3.
down the
length of the
Front Fascia
until it is firmly
secured onto
the Wall Plate
A
B
Installation Complete
Shelf
G.1.
Slide the Front
Fascia through the
cut outs in the
Shelves
Insert the Cable Tabs into
the Wall Plate to Secure
Cables in place.
If required, cables can exit
from the side of the Cable
Manager. In this case, use
the left or right cable bays
only.
Cables exiting from the side
E.1.
Using your
thumb and
index finger,
flex the Cable
Tab into a
concave shape

Produktspezifikationen

Marke: Atdec
Kategorie: Unterstützung für Flachbildschirme
Modell: TH-CM-SH-2

Brauchst du Hilfe?

Wenn Sie Hilfe mit Atdec TH-CM-SH-2 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Unterstützung für Flachbildschirme Atdec

Atdec

Atdec TH-30-50-RW Bedienungsanleitung

21 August 2024
Atdec

Atdec TH-3070-CTW Bedienungsanleitung

21 August 2024
Atdec

Atdec L-PB Bedienungsanleitung

20 August 2024
Atdec

Atdec SD-DP-750 Bedienungsanleitung

20 August 2024
Atdec

Atdec VF-AT-D Bedienungsanleitung

20 August 2024
Atdec

Atdec AF-AT-D Bedienungsanleitung

20 August 2024
Atdec

Atdec VFS-DH/TAA Bedienungsanleitung

20 August 2024
Atdec

Atdec SD-DO-42-BK Bedienungsanleitung

20 August 2024
Atdec

Atdec TH-PS-D Bedienungsanleitung

20 August 2024
Atdec

Atdec TH-PPA-2448 Bedienungsanleitung

19 August 2024

Bedienungsanleitung Unterstützung für Flachbildschirme

Neueste Bedienungsanleitung für -Kategorien-

NEC

NEC PDVWXUN 55 P Bedienungsanleitung

16 Oktober 2024
Insignia

Insignia NS-STV3N1705 Bedienungsanleitung

15 Oktober 2024
Abus

Abus BW8060 Bedienungsanleitung

4 Oktober 2024
One For All

One For All DM 4110 Bedienungsanleitung

2 Oktober 2024
One For All

One For All DM 7220 Bedienungsanleitung

2 Oktober 2024
One For All

One For All DM 2220 Bedienungsanleitung

2 Oktober 2024
Kogan

Kogan KASMM39S12A Bedienungsanleitung

1 Oktober 2024
Kogan

Kogan KATWM70TLMA Bedienungsanleitung

1 Oktober 2024
Kogan

Kogan KADMM46G24A Bedienungsanleitung

1 Oktober 2024
Kogan

Kogan KADMMPCGASC Bedienungsanleitung

1 Oktober 2024