Atdec SD-DO Bedienungsanleitung
Atdec
Flat panel steun
SD-DO
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Atdec SD-DO (2 Seiten) in der Kategorie Flat panel steun. Dieser Bedienungsanleitung war für 3 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/2
Component Checklist
Installation Instructions
A. Use this configuration with a
standard 50mm pole
(No inserts required)
B. Use this configuration with a
Visidec 42mm extrusion
pole
C.
Use this configuration with a
standard 42mm pole
Step 1. Install Quickshift Donut
42mm Front
Donut Insert (x1)
Visidec Groove
Lock (x1)
42mm Rear
Donut Insert (x1)
5mm Allen
Key (x1)
Hardware Mounting
Screws
M4x10mm
Screw (x4)
M4x12mm
Screw (x4)
M4x16mm
Screw (x4)
Select your correct product configuration: A, B, or C.
Rear Donut
Insert
Rear Donut
Insert
Front Donut
Insert Front Donut
Insert
Groove
Insert
Check you have received all parts against this Component Checklist prior to installation.
Tightening
Tool (x1)
2mm Allen
Key (x1)
Slide the Quickshift Donut onto the pole
(with the lever open), removing the End
Cap if necessary.
Rear groove insert must align with slot in
the Pole.
(Visidec 42mm pole shown)
TIGHTEN
LOOSEN
Once in place, close the lever
to lock the Quickshift Donut
in the desired position.
Slide the Quickshift Donut into the desired position.
If necessary, adjust the tension between the
Quickshift Donut and the Pole using the 5mm Allen
Key supplied.
Slot
OR OR
Groove
Insert
Security
Screw (x1)
CLOSE
WARNING: Be careful not to overtighten
! The Spacedec Display Quickshift Donut is to be used on 42mm and 50mm diameter poles only.
! The Manufacturer accepts no responsibility for incorrect installation.
Display | Quickshift Donut
Quickshift
Donut (x1)
Note: Ensure inserts are fitted
in correct orientation.
Arrows point
to top surface
SD-DO
No portion of this document or any artwork contained herein should be reproduced in any way without the express written consent of Atdec Pty Ltd.
Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published: 18.05.09 ©
Step 2. Remove VESA plate from Quickshift Donut
Step 5. Adjusting the VESA Ball Mount
Position your Display to the desired viewing angle, using the 40°
angular movement allowed by the VESA Ball Mount.
Depending on the weight of the display, it may be necessary to make
adjustments to the VESA Ball the display Mount. If does not hold its
position, or is too resistant, adjust the Tension Plate located at the
rear of the VESA Ball Mount (see diagram right).
To make any adjustments, use the Tightening Tool supplied.
Check the display, and then adjust again if necessary.
Installation Complete
Step 4. Attach your Display to the Quickshift Donut
Press and hold the Release Buttons (one on either side).
Release
Button
Whilst holding the Release Buttons, remove the VESA Plate.
LIFT
TIGHTEN
Hook the top of the VESA plate onto
the Quickshift Mount.
Insert the Security Screw, and tighten
using the 2mm Allen Key.
CLICK
Gently push the bottom of the Display
into the Mount until it ‘CLICKS’.
Back of Display
VESA Plate
Release
Buttons
Tightening
Tool
Tension
Plate
Loosen (-Kg)
Tighten (+Kg)
Step 3. Attach the VESA plate to your Display
There are two mounting hole configurations:
UÊÇxÊÝÊÇx
UÊ£ääÊÝÊ£ää
Choose appropriate Mounting Screws
from the Hardware supplied to suit
your Display. Top of
Display
Mounting Screws (x4)
VESA Plate
Back of Display
Çx
(3”) 100mm
(4”)
Çx
(3”)
100mm
(4”)
VESA plate
Produktspezifikationen
Marke: | Atdec |
Kategorie: | Flat panel steun |
Modell: | SD-DO |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Atdec SD-DO benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Flat panel steun Atdec
21 August 2024
20 August 2024
20 August 2024
20 August 2024
20 August 2024
19 August 2024
19 August 2024
18 August 2024
18 August 2024
18 August 2024
Bedienungsanleitung Flat panel steun
- Flat panel steun Samsung
- Flat panel steun Da-Lite
- Flat panel steun HP
- Flat panel steun Kensington
- Flat panel steun Manhattan
- Flat panel steun Schwaiger
- Flat panel steun König
- Flat panel steun Atlantic
- Flat panel steun Luxor
- Flat panel steun Hitachi
- Flat panel steun Icy Box
- Flat panel steun Cabstone
- Flat panel steun Techly
- Flat panel steun Vogel's
- Flat panel steun SilverStone
- Flat panel steun Vision
- Flat panel steun InFocus
- Flat panel steun NEC
- Flat panel steun Marantz
- Flat panel steun Monoprice
- Flat panel steun Fellowes
- Flat panel steun Iiyama
- Flat panel steun Kogan
- Flat panel steun Acco
- Flat panel steun HQ
- Flat panel steun Sanus
- Flat panel steun B-Tech
- Flat panel steun Barkan
- Flat panel steun Ergotron
- Flat panel steun NewStar
- Flat panel steun Speaka
- Flat panel steun Digitus
- Flat panel steun Reflecta
- Flat panel steun BlueBuilt
- Flat panel steun Peerless-AV
- Flat panel steun Ematic
- Flat panel steun GPX
- Flat panel steun Peerless
- Flat panel steun Steren
- Flat panel steun AMX
- Flat panel steun Ultimate
- Flat panel steun BakkerElkhuizen
- Flat panel steun Chief
- Flat panel steun Siig
- Flat panel steun StarTech.com
- Flat panel steun APart
- Flat panel steun Planar
- Flat panel steun Proaim
- Flat panel steun Konig & Meyer
- Flat panel steun Premier Mounts
- Flat panel steun Gabor
- Flat panel steun V7
- Flat panel steun Rocstor
- Flat panel steun Avteq
- Flat panel steun Zaor
- Flat panel steun CTA Digital
- Flat panel steun Bell'O
- Flat panel steun Anthro
- Flat panel steun Mount-It!
- Flat panel steun My Wall
- Flat panel steun SmartMetals
- Flat panel steun Multibrackets
- Flat panel steun Walker Edison
- Flat panel steun LTN Technologies
- Flat panel steun Heckler
- Flat panel steun Helder
Neueste Bedienungsanleitung für -Kategorien-
17 September 2024
15 September 2024
15 September 2024
15 September 2024
12 September 2024
10 September 2024
9 September 2024
8 September 2024
6 September 2024
6 September 2024