American International NDK724 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für American International NDK724 (4 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 29 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/4
NDK724 Mounting Kit
Nissan
2011 ROGUE
2012-13 ROGUE (Without 4.3 color display radios)
2007-12 SENTRA
VEHICLE APPLICATIONS (ISO Mount Only)
©2015 AMERICAN INTERNATIONAL INDUSTRIES, INC. TECH Ver. 6/13 PRINT Ver. 2/15
1. Carefully lift up and remove the top cover plate from the top of radio/pocket assembly.
2. Remove the (2) Phillips screws from top of radio trim bezel (located under the cover
plate removed in step 1.
3. Carefully lift up the trim from around the shifter lever enough to be able to remove
the panel above.
4. Carefully pull forward the climate control module and lay out of the way.
5. Remove the (2) Phillips screws from the lower radio trim bezel.
6. Carefully pull the Radio/pocket trim bezel forward, disconnect all attached harnesses
and remove the Radio/pocket trim bezel assembly.
7. Remove the (4) Phillips screws securing the factory radio/pocket assembly brackets to
the outermost corners of the trim bezel.
8. Remove the (8) T-20 torx screws securing the factory radio to the factory metal
mounting brackets then remove factory radio.
DASH DISASSEMBLY INSTRUCTIONS
1. Using a panel removal tool, carefully pry the front edge of the center channel speaker
cover upward to unclip and remove from the top of the dash.
2. Remove the (4) Phillips screws securing the center channel speaker (If equipped).
3. Disconnect the center channel wire harness from the speaker and remove speaker
if equipped.
4. Carefully pry the lower side edge trim pieces from beside the Vent/Hazard assembly,
then using a panel removal tool from inside the center channel speaker area at the
top of the dash, slide the panel removal tool between the center channel speaker
mount surface, and the base beneath the center channel speaker mount surface and
pry upward on the Vent panel assembly, disconnect all harnesses from the rear of
the panel and remove assembly.
5. Using a panel removal tool, carefully pry the climate control panel forward and lay out
of the way.
6. Using a panel removal tool, carefully pry and remove the radio panel including
air vents. Unplug hazard button.
7. Remove the (4) Phillips screws securing the radio to the sub-dash.
8. Carefully pull the radio forward, disconnect all wire harnesses and antenna lead
and remove radio
DASH DISASSEMBLY INSTRUCTIONS
2007-12 NISSAN SENTRA
2011-13 NISSAN ROGUE
2
This kit is an ISO mount only kit. (The metal sleeve that comes with your new radio
cannot be used)
NOTE: This kit is designed to accommodate only single ISO mount aftermarket radioʼs that
have a trim ring around the face that is designed to be easily removed per the radio
manufacturers instructions. Due to variances in the sizes of the faces of aftermarket
radioʼs, some modification may be necessary to the kit, the factory bezel, or both.
1. Insert the IMB724 L & R side mounting brackets into the sides of the NDK724 kit and
secure to the back of the pocket using the 2 small Phillips screws supplied with kit.
(See illustration)
2. Attach the kit to the factory radio mounting brackets using 2 of the large Phillips
screws supplied with the NDK724 installation kit (line up the kit to use the same
lower mounting holes the factory radio used) Pocket must be on the bottom.
3. Insert the new radio (without the metal sleeve and radio face trim ring) above the
NDK724 pocket and attach to the factory mounting brackets using 2 of the large
Phillips screws supplied with the NDK724 installation kit. (Line up the new radio to
use the same upper mounting holes the factory radio used)
4. Re-attach the factory mounting brackets with the new radio/kit installed into the rear
side of the factory radio/pocket trim assembly using the (4) Phillips screws removed
in step 8 of the dash disassembly instructions.
NOTE: If the top portion of the NDK724 bends when the dash is installed. you may need
to round/trim the upper left and right of the dash kit, due to dash size variances.
KIT & RADIO INSTALLATION INSTRUCTIONS
IMB724 L
IMB724 R
Fig. A
3


Produktspezifikationen

Marke: American International
Kategorie: Nicht kategorisiert
Modell: NDK724

Brauchst du Hilfe?

Wenn Sie Hilfe mit American International NDK724 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert American International

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-