American International HONK836 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für American International HONK836 (4 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 10 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/4
Honda
2006-14 RIDGELINE
VEHICLE APPLICATIONS
HONK836 Mounting Kit
©2014 AMERICAN INTERNATIONAL INDUSTRIES, INC. TECH Ver. 01/15 PRINT Ver. 01/15
1. Engage the parking brake.
2. Lower the steering column all the way down.
3. Carefully unfasten and pull outward the entire Radio/Dash trim bezel, disconnect all
harnesses attached to the rear of the dash trim bezel and remove bezel.
4. Remove the (5) Phillips screws securing the radio/pocket assembly to the sub-dash.
5. Carefully pull radio assembly forward, disconnect all harnesses and the antenna lead
from the rear of the radio and remove radio assembly.
NOTE: ISO trim ring (ITR-836) may be used in place of after-market radio’s removable trim ring.
DASH DISASSEMBLY INSTRUCTIONS
KIT ASSEMBLY INSTRUCTIONS
2
Main Frame
IMB836L
IMB836R
ITR836
(Use Optional)
Single DIN Mount Applications
1. Attach the left and right side brackets to the main bracket. See Figure B opposite page.
2. Insert pocket (part # POC836) into upper section of the main frame.
3. Attach left and right side brackets to the rear of the pocket using screws supplied.
4. Insert DIN sleeve from your new radio into the lower section of the installation kit.
5. Depress the tabs from inside the sleeves opening upward, outward, and downward
to secure sleeve to the installation kit.
6. Install radio into sleeve and lock into place.
7. Attach a rear support bracket to the rear of the new radio and adjust as necessary to
attach to the rear support stud located on the back of the pocket using the small
phillips screw supplied with kit.
8. Remove factory pocket from factory radio mounting brackets & re-attach to lower
mounting brackets of HONK836 kit using factory screws.
Single ISO Mount Applications
1. Attach the left and right side brackets to the main bracket. See Figure B below.
2. Insert pocket (part # POC836) into upper section of the main frame.
3. Attach left and right side brackets to the rear of the pocket using screws supplied.
4. Attach (1) ISO Spacer to the inside of lower section on both Left & Right mounting
brackets as shown in Fig. A below. (See note #2 below)
5. Insert ISO mountable radio between ISO mount brackets and loosely attach to sides
of radio using screws provided with radio when possible or hardware included with kit.
Note: Use larger screws for lower ISO mount location only.
6. Slide radio component forward or backward for desired look and tighten screws.
7. Attach a rear support bracket to the rear of the new radio and adjust as necessary to
attach to the rear support stud located on the back of the pocket using the small
phillips screw supplied with kit.
NOTE: 1) ISO trim ring (ITR836) may be used in place of after-market radio’s removable trim ring.
2) Spacers must read upright (This side up for single ISO install).
ITR836
(Use Optional)
For ISO mount only: Attach (1) ISO
Spacer to the inside of lower section on
both Left & Right mounting brackets
as shown in Fig. A.
POC836
Fig. A
KIT ASSEMBLY INSTRUCTIONS
3
Fig. B
Main Frame
IMB836L
IMB836R
Left
Right


Produktspezifikationen

Marke: American International
Kategorie: Nicht kategorisiert
Modell: HONK836

Brauchst du Hilfe?

Wenn Sie Hilfe mit American International HONK836 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert American International

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-