Aerohive AP1130 Bedienungsanleitung

Aerohive Zugangspunkt AP1130

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Aerohive AP1130 (13 Seiten) in der Kategorie Zugangspunkt. Dieser Bedienungsanleitung war für 9 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/13

P/N 330120-02, Rev. A 1

AP1130 Installation Guide

The AP1130 is a multi-channel wireless access point with a watertight chassis that can be

deployed in virtually any outdoor setting, including extreme environments.

This guide explains how to install the AP1130 on a pole or flat surface in virtually any

outdoor setting, and connect it to Aerohive HiveManager Network Management over the

network. To register, get the latest product documentation, see compliance information, and

download software updates, visit www.aerohive.com/support. For detailed hardware

information about this device, visit www.aerohive.com/quick.

FCC and IC statements can be found on page 12.

Kit Contents, Required Accessories, and Tools

The AP1130 kit includes the items shown below.

To install your AP1130, you will need the following accessories (ordered separately) and tools:

• Two 2.4 GHz antennas

• Two 5 GHz antennas

• A switch that provides PoE power, or a PoE provisioning device, a DC backup battery (requires the

DC power cable accessory, part number AH-ACC-1130-CBL-DC), or solar panel

• A shielded cat5 Ethernet cable rated for outdoor use; length not to exceed 328 feet (100 m)

• PoE Injector (optional).

• Crosshead screwdriver for pan head screws and Reset button cover

• Flat blade screwdriver to tighten the hose clamp

• Security Torx (pin-in-Torx) screwdriver for the captive screws in the mounting bracket

Bracket (1)

AP1130

chassis

Five pan head machine

screws with washers for

pole mount and ground in

bag labelled “POLE MOUNT &

GROUNDING”

Four pan head wall

mount screws in the bag

labeled “WALL MOUNT”

Hose clamp

Ground cable (1)

Waterproof

Ethernet housing

Aerohive Networks

Hardware Components

The following illustration shows the AP1130 hardware components. For detailed descriptions of these

components and additional specifications, see the online Help for the AP1130 at www.aerohive.com/quick.

Safety Instructions and Site Hazard Warnings

Read and follow these safety instructions and hazard warnings before installing an AP1130. Keep these

instructions for future reference.

The following icons are used to identify the type of caution or warning in this document:

Refer to the following cautions and warnings when installing your AP1130.

This icon indicates a general caution. Failure to comply with a caution notification can result in damage to equipment.

This icon indicates an electrical caution. Failure to comply with an electrical notification can result in serious injury or death, and

extensive damage to equipment.

5GHz (0) 5GHz (1)

2 4GHz (0) Eth0 PoE+ 12VDC 0 ) 2 4 GH

S atus

Bracket

mounting hole

Bracket

mounting hole

Bracket

mounting hole

Bracket

mounting hole

Hole for ground

Reset button

R et

Top Panel

Bottom Panel

Right Panel

Left Panel

Back Panel

5 GHz

connector

5 GHz antenna

connector

5 GHz

connector

5 GHz

connector

Pressure

vent

Eth0/PoE 12VDC

(2.0A)

Status

LED

2.4 GHz

connector

2.4 GHz

connector

2.4 GHz

connector

2.4 GHz

connector

5GHz 2.4 GHz Ethernet

LED LED LED

Signal

strength LED

Aerohive Networks

Installing the AP1130

You can mount the AP1130 outdoors on a horizontal or vertical pole, or on an indoor or outdoor wall. You

can adjust the orientation of the AP1130 for optimum radio transmission. For example, you can mount the

AP1130 on a non-penetrating roof stand or to a Winegard bracket, often used for mounting satellite dishes.

To provide unobstructed RF coverage, mount the AP1130 in a relatively open area on a pole, mast, of flat

surface so that the antennas have at least a three-foot clearance from any nearby obstructions.

Aerohive devices must be installed by a professional installer who is certified to install these types of devices and to ensure that they are

properly grounded and meet applicable local and national electrical codes.

Do not install the device in an environment where the operating ambient temperature might exceed the recommended ranges.

Changes or modifications made to this device that are not expressly approved by the party responsible for compliance could void the user's

authority to operate the equipment.

For reliable connections in all conditions, especially in wet and windy locations, you must use the Ethernet cable housing.

For products available in the USA/Canada market, for the 2.4 GHz band, only channels 1-11 can be operated. Selection of other channels is

not possible.

Use only attachments and accessories specified by Aerohive.

These devices are not designed or approved for use with power lines other than 110-120V or 220-240 volts, 50/60 Hz, single phase

(depending on the country in which they are being used). Attempting to use these devices on non-approved power lines may have

hazardous consequences.

Do not plug these devices into a filtered power strip or AC line filter.

These devices are not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or with lack of

experience of knowledge unless they are given supervision or instruction concerning use of the devices by a person who is responsible for

their safety. Children should be supervised to ensure that they do not play with the devices.

Electrostatic discharge (ESD) can damage equipment and impair electrical circuitry. ESD damage occurs when electronic components are

improperly handled and can result in complete or intermittent failures. Be sure to follow ESD-prevention procedures when handling

electronic components.

Disconnect all power by turning off the power switch and unplugging the power cord before installing or removing a device, or working

near power supplies.

Never assume that power is disconnected from a circuit; always check the circuit.

Reliable grounding of equipment should be maintained. Particular attention should be given to supply connections other than direct

connections to the branch circuit (e.g. use of power strips.)

To protect the AP1130 from lightning, do not place it at the highest point of a building or structure.

During operation, the surfaces of the AP1130 can become hot. Use caution when handling.

Make sure that the AP1130 is connected to a suitably installed ground conductor. Contact the appropriate electrical inspection authority if

you are uncertain that suitable grounding is available.

Do not locate the AP1130 enclosure near overhead power lines or other electric light or power circuits, or where it can come into contact

with such circuits. During installation, exercise extreme care not to come into contact with these circuits, which can cause serious injury or

death. For proper installation and grounding of the product, refer to national and local electrical codes: NFPA (National Fire Protection

Association) 70, National Electrical Code Article 810 (U.S.); Canadian Electrical Code, Part I, CSA 22.1 and Section 54 (Canada); and if local

or national electrical codes are not available, refer to IEC (International Electrotechnical Commission) 364, Part 1 through 7 (other countries).

Do not connect or disconnect antennas or cables from the AP1130 during periods of lightning activity.

Produktspezifikationen

Marke:	Aerohive
Kategorie:	Zugangspunkt
Modell:	AP1130
Breite:	196 mm
Tiefe:	196 mm
Gewicht:	1079 g
Produktfarbe:	Weiß
Internationale Schutzart (IP-Code):	IP67
Höhe:	54 mm
Platzierung:	Pole, Wall
AC Eingangsspannung:	12 V
Betriebstemperatur:	-40 - 55 °C
Netzstandard:	IEEE 802.11a, IEEE 802.11ac, IEEE 802.11b, IEEE 802.11g, IEEE 802.11n, IEEE 802.3at
Unterstützte Sicherheitsalgorithmen:	802.1x RADIUS, TKIP, WEP, WPA, WPA2
Power over Ethernet (PoE):	Ja
Anzahl Ethernet-LAN-Anschlüsse (RJ-45):	1
Maximale Datenübertragungsrate:	1000 Mbit/s
Ethernet LAN Datentransferraten:	10,100,1000 Mbit/s
2,4 GHz:	Ja
Eingebaut:	Nein
Temperaturbereich bei Lagerung:	-40 - 80 °C
Montageset:	Ja
DHCP-Client:	Ja
5 GHz:	Ja
Antennenfunktionen:	Abnehmbare Antenne