Cisco AIR-CAP702I-I-K9 Bedienungsanleitung

Cisco Zugangspunkt AIR-CAP702I-I-K9

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Cisco AIR-CAP702I-I-K9 (26 Seiten) in der Kategorie Zugangspunkt. Dieser Bedienungsanleitung war für 12 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/26
G ETTING S GTARTED UIDE
Cisco Aironet 700 Series Access Points
First Published: June 2013
Last Updated: September 2014
1About this Guide
2Introduction to the Access Point
3Safety Instructions
4Unpacking
5Configurations
6Access Point Ports and Connectors
7Configuring the Access Point
8Mounting the Access Point
9Deploying the Access Point on the Wireless Network
10 Troubleshooting
11 Declarations of Conformity and Regulatory Information
12 Configuring DHCP Option 43 and DHCP Option 60
13 Access Point Specifications
2
1 About this Guide
This Guide provides instructions on how to install and configure your Cisco Aironet 700 Series Access Point. The 700 Series
Access Point is referred to as the 700 series or the access point in this document.
2 Introduction to the Access Point
The 700 series supports high-performing two spatial stream rates over a deployable distance with high reliability when serving
clients. The 700 series provides high reliability and overall wireless performance.
The 700 series offers dual-band radios (2.4 GHz and 5 GHz) with integrated internal antennas. The access point supports full
inter-operability with leading 802.11n clients.
The 700 series access point is available in the controller-based and autonomous configurations and supports:
Simultaneous dual-band (2.4 GHz/5 GHz) radios
Integrated antennas on 702I access point models (AIR-CAP702I-x-K9)
Note The ‘x in the model numbers represents the regulatory domain. Refer to “Regulatory Domains section on page 4
for a list of supported regulatory domains.
The features of the 700 series are:
Processing sub-systems for controller-based models (including CPUs and memory) and radio hardware which supports:
Unified
FlexConnect
Monitor-mode
Note Enhanced Local Mode (ELM) is not supported.
The following processor features:
128 MB NAND flash size
1 MB NOR flash size
128 MB DDR2 memory bus, x32
2.4 GHz and 5 GHz 802.11n radios with the following features:
802.11n standard compliant
A-MPDU TX
HT Duplicate Mode
2TX x 2RX
2-spatial streams, 300 Mbps PHY rate
Maximal ratio combining (MRC)
Cyclic Shift Diversity (CSD)
MCS0-MCS15; Short or Long Guard Intervals
DFS for UNII-2 and UNII-2 Extended channels, including 0.5us radar pulse detection
3 Safety Instructions
Translated versions of the following safety warnings are provided in the translated safety warnings document that is shipped
with your access point. The translated warnings are also in the Translated Safety Warnings for Cisco Aironet Access Points,
which is available on Cisco.com.
3
Warning
IMPORTANT SAFETY INSTRUCTIONS
This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any
equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for
preventing accidents. Use the statement number provided at the end of each warning to locate its translation in
the translated safety warnings that accompanied this device.
Statement 1071
SAVE THESE INSTRUCTIONS
Warning
Read the installation instructions before you connect the system to its power source.
Statement 1004
Warning
Installation of the equipment must comply with local and national electrical codes.
Statement 1074
Warning
This product relies on the buildings installation for short-circuit (overcurrent) protection. Ensure that the
protective device is rated not greater than:
20A.
Statement 1005
Warning
Do not operate your wireless network device near unshielded blasting caps or in an explosive environment unless
the device has been modified to be especially qualified for such use.
Statement 245B
Warning
In order to comply with FCC radio frequency (RF) exposure limits, antennas should be located at a minimum of 7.9
inches (20 cm) or more from the body of all persons.
Statement 332
Caution The fasteners you use to mount an access point on a ceiling must be capable of maintaining a minimum pullout
force of 20 lbs (9 kg) and must use all 4 holes on the mounting bracket.
Caution This product and all interconnected equipment must be installed indoors within the same building, including the
associated LAN connections as defined by Environment A of the IEEE 802.af Standard.
Note The access point is suitable for use in environmental air space in accordance with section 300.22.C of the National
Electrical Code and sections 2-128, 12-010(3), and 12-100 of the Canadian Electrical Code, Part 1, C22.1. You should
not install the power supply or power injector in air handling spaces.
Note Use only with listed ITE equipment.


Produktspezifikationen

Marke: Cisco
Kategorie: Zugangspunkt
Modell: AIR-CAP702I-I-K9

Brauchst du Hilfe?

Wenn Sie Hilfe mit Cisco AIR-CAP702I-I-K9 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Zugangspunkt Cisco

Bedienungsanleitung Zugangspunkt

Neueste Bedienungsanleitung für -Kategorien-