Yealink WF40 Bedienungsanleitung

Yealink Dongle WF40

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Yealink WF40 (2 Seiten) in der Kategorie Dongle. Dieser Bedienungsanleitung war für 16 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/2

Wi-Fi USB Dongle WF40

User Guide

Wi-Fi USB Dongle WF40 is used to connect IP phones to

the organization’s wireless network. Wi-Fi USB dongle is a

cost-effective solution for small office wireless networking,

which allows you to experience the convenience of wireless

networking.

Packaging Contents

Wi-Fi USB Dongle

User Guide

www.yealink.com

The following items are included in your package. If you find

anything missing, contact your system administrator.

Why can’t the IP phone connect to the wireless network?

If the network is secure, ensure the entered password is

right.

Ensure your gateway/router enables the wireless network

feature.

Reboot your gateway/router.

Turn off the Wi-Fi feature on the IP phone and then turn it

on again.

Why is the wireless signal strength low?

Ensure the IP phone and your gateway/router are within

the working range and there is no obvious interference

(walls, doors, etc) between them.

Yealink(Xiamen) Network Technology Co.,Ltd.

309, 3rd Floor, No.16, Yun Ding North Road, Huli District,

Xiamen City, Fujian, P.R.C

YEALINK(EUROPE) NETWORK TECHNOLOGY B.V.

Address WTC Schiphol Airport, B tower, 5th floor, :

Schiphol Boulevard 231, 1118 BH Amsterdam Schiphol, the

Netherlands

YEALINK(USA) NETWORK TECHNOLOGY CO., LTD.

Address 999 Peachtree Street Suite 2300, Fulton, Atlanta, :

GA, 30309, USA

Connecting the IP phone to an Available Wiereless Network

Assembling the Wi-Fi USB Dongle

To manually connect the IP phone to an available wireless network

(take the SIP-T48G IP phone for example):

Assembling the Wi-Fi USB Dongle, as shown below:

To assemble the Wi-Fi USB Dongle:

1. Insert the Wi-Fi USB Dongle into the USB port on the

back of the phone.

After your phone is powered on and the system boots up,

you can connect the IP phone to an available wireless

network.

WiFi USB Dongle WF40 User Guide

www.yealink.com

6. Tap .OK

2. Tap to activate Wi-Fi mode directly and scan Wi-Fi OK

devices automatically.

Disabling Wi-Fi Feature on the IP Phone

To disable Wi-Fi feature, do one of the following (take the SIP-T48G IP

phone for example):

- Tap -> -> . Basic Wi-Fi

Mark the radio box in the field. Off Wi-Fi

1. Insert the Wi-Fi USB Dongle WF40 into the USB port on the

back of the phone when the phone is idle.

The touch screen prompts “Wi-Fi adapter has been added,

scanning the available wireless network right now?”

3. (Optional.) To re-search the available network, tap the Scan

soft key.

4. Tap the desired wireless network to connect to your IP phone.

You can also tap after the desired wireless network, and

then tap Connect.

Once the connection has completed successfully, the prompt

“Connect Success.” appears at the end of the desired SSID.

5. If the network is secure, enter its password in the field.Pin

You can also configure the Wi-Fi feature at the path: ->

Basic Wi-Fi-> .

Note: Contact your network administrator for the Wi-Fi

password.

- Unplug the Wi-Fi USB dongle from the IP phone.

The IP phone toggles the Wi-Fi to off.

Troubleshooting

Why can’t the Wi-Fi feature be enabled?

Ensure the Wi-Fi USB dongle is not broken.

Ensure the Wi-Fi USB dongle is assembled and detected

by the phone successfully.

Produktspezifikationen

Marke:	Yealink
Kategorie:	Dongle
Modell:	WF40
WLAN:	Ja
WLAN-Standards:	802.11b,802.11g,Wi-Fi 4 (802.11n)
Produktfarbe:	Schwarz
Übertragungstechnik:	Kabellos
Netzstandard:	IEEE 802.11b,IEEE 802.11g,IEEE 802.11n
Unterstützte Sicherheitsalgorithmen:	64-bit WEP,128-bit WEP,152-bit WEP,WPA2-PSK
Warentarifnummer (HS):	85176990
Maximale Datenübertragungsrate:	150 Mbit/s
Eingebaut:	Nein
USB-Version:	2.0
Schnittstelle:	WLAN
Top WLAN-Standard:	Wi-Fi 4 (802.11n)
Datenübertragungsgeschwindigkeit WLAN:	150 Mbit/s
Bandbreite:	2.4 GHz
Hostschnittstelle:	USB
Bandbreite (erste):	2.4 GHz