Yamaha NS-U50 Bedienungsanleitung
Yamaha
Lautsprechersystem
NS-U50
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Yamaha NS-U50 (1 Seiten) in der Kategorie Lautsprechersystem. Dieser Bedienungsanleitung war für 12 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/1
PRECAUTIONS
Read these precautions carefully before using your speaker.
• Any time you note distortion, reduce the volume control on
your amplifier to a lower setting. Never allow your amplifier
to be driven into “clipping”. Otherwise the speaker may be
damaged.
• When using an amplifier with a rated output power higher
than the nominal input power of the speaker, care should
be taken never to exceed the speaker’s maximum input.
• Do not attempt to clean the speaker with chemical
solvents as this might damage the finish. To clean, wipe
with a dry, soft cloth.
• To prevent the enclosure from warping or discoloring, do
not place the speaker where it will be exposed to direct
sunlight or excessive humidity.
• Do not place the speaker where it is liable to be knocked
over or struck by falling objects. Stable placement will also
ensure better sound performance.
• Placing the speaker on the same shelf or rack as the
turntable can result in feedback.
• This speaker system is designed for home use only. Never
use this speaker system inside a car.
• Secure placement or installation is the owner’s
responsibility.
YAMAHA shall not be liable for any accident caused
by improper placement or installation of the speaker.
ATTACHING STAND
Attach the included stands to the
speakers using the two included
screws. Place the speakers next
to a personal computer on a
desktop to achieve the optimum
listening position. Be sure to
attach the stands to the speakers
correctly as shown in the figure.
If you attach them in the opposite
direction or otherwise incorrectly,
the speakers may fall and be
damaged or cause injury.
■Non skid pad
To prevent the speakers from sliding around, attach the
supplied pads as shown in the illustration.
You can also use the screw holes on the rear of the speaker
for installing the speakers.
60 mm A screw with a diameter of 4 mm and a
pitch of 0.7 mm can be used.
(Depth of hole: 8 mm)
NS-U50
CONNECTION TO YOUR AMPLIFIER
BEFORE MAKING CONNECTIONS, MAKE SURE THAT
THE AMPLIFIER IS SWITCHED OFF.
■CONNECTIONS
• Connect the push-type input terminals at the rear of the
speakers to the speaker output terminals of your amplifier
with the provided speaker cord.
• One side of the speaker cord is marked by a red line.
Connect the (+) terminals on both the amplifier and the
speakers using this red-marked side. Connect the (–)
terminals on both components using the black-side of the
cord.
• Connect one speaker to the left (marked L) terminals of
your amplifier, and another speaker to the right (marked R)
terminals, making sure not to reverse the polarity (+, –). If
one speaker is connected with reversed polarity, the sound
will be unnatural and lack bass.
Procedures:
1Press the tab on the terminal down, as shown in the
figure.
2Insert the bare speaker wire end properly into the terminal
hole. [Remove approx. 5 mm (1/4") insulation from the
speaker cord.]
3Remove your finger from the tab to allow it to lock snugly
on the cord’s wire end.
4Test the security of the connection by tugging lightly on the
cord at the terminal.
ANALOG
PC IN
AUX 1
IN
SUB
WOOFER
OUT
IN
OUT
AUX 2
R L
ANTENNA
AM
FM
75 Ω
UNBAL
GND
DIGITAL
SPEAKERS
6Ω MIN./SPEAKER
+
–
USB
OPT OUT
AUX 1
OPT IN
COAX IN
PC
OPT IN
R L
SPEAKERS
6 MIN./SPEAKERΩ
+
–
R L
Speaker (R)
(RP-U100)
Speaker (L)
Red line
Black line
–
+
Note:
Do not let the bare
speaker wires touch each
other as this could
damage the speaker and/
or the amplifier.
*
*
*
* Non skid
pad
SPECIFICATIONS
Natural Sound 2-way Acoustic
Suspension Speaker System
Printed in Malasia
IP
V425250
G
Type : 2-way acoustic suspension
magnetic shielding
Driver : Woofer ..... 9 cm (3-1/2") cone
Tweeter .... 2.5 cm (15/16")
balanced dome
Nominal input power : 40 W
Maximum input power : 100 W
Frequency response : 75 Hz – 30 kHz
Sensitivity : 88 dB
Crossover frequency : 5 kHz
Impedance : 6Ω
Dimensions (W × H D) :×
110 (4.3") × 293 (11.5") × 192 (7.6") mm
(stand included)
Weight : 2.0 kg (4.4 lbs) (stand included)
Accessories : Stand × 2
Screws for stand × 4
Non skid pad × 8
Speaker cord × 2
Produktspezifikationen
| Marke: | Yamaha |
| Kategorie: | Lautsprechersystem |
| Modell: | NS-U50 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Yamaha NS-U50 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Lautsprechersystem Yamaha
6 Juli 2024
5 Juli 2024
5 Juli 2024
5 Juli 2024
5 Juli 2024
5 Juli 2024
4 Juli 2024
3 Juli 2024
3 Juli 2024
3 Juli 2024
Bedienungsanleitung Lautsprechersystem
- Lautsprechersystem Samsung
- Lautsprechersystem Sony
- Lautsprechersystem Panasonic
- Lautsprechersystem AEG
- Lautsprechersystem Grundig
- Lautsprechersystem Auna
- Lautsprechersystem Pioneer
- Lautsprechersystem JBL
- Lautsprechersystem Onkyo
- Lautsprechersystem Technics
- Lautsprechersystem Toshiba
- Lautsprechersystem Jamo
- Lautsprechersystem ION
- Lautsprechersystem American Audio
- Lautsprechersystem Paradigm
- Lautsprechersystem BW
Neueste Bedienungsanleitung für -Kategorien-
25 August 2024
25 August 2024
25 August 2024
24 August 2024
23 August 2024
23 August 2024
22 August 2024
22 August 2024
22 August 2024
22 August 2024