XOMAX XM-DTSB912 Bedienungsanleitung


Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr XOMAX XM-DTSB912 (8 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war fĂĽr 33 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/8
Please read all instructions carefully before using
INSTRUCTIONS
1. Basic Operation
4. Additional Information
3. Basic operation of setup menu
2. Function Operation
Panel Introduction 02
Remote control function 04
BT Function 09
General setting 12
Steering Wheel setting 13
Trouble shooting 14
Touch calibration 14
13
Video setting
Audio setting 13
Language setting 13
Time setting 12
Other Function Operations 11
11
External input operation (Optional)
Disc Function Operation 08
Radio Function Operation 07
U Disc SD Card function operation/ 06
Access main interface 06
Turn the Unit On/Off 06
14
Trouble shooting
PROBLEM CAUSE CORRECT ACTION
Poor performance of
radio station
Cannot load disk There is a disk inside
After ignition switch
off, setting
information all lose
Reset information and save
Change battery or fuse
Cannot power on Change fuse same as the old one
Some factors cause MPU wrong operation Press RES button on the panel by
power on
penpoint, then,
Weak signal Move the car to another place, then research
Cannot play disc
Disc is scratched Change new disc
Put wrong side of disc into the unit Slot to in the disk with sign side up
Clean lens by lens clean disc
Cannot switch
language/subtitle There is only one language/subtitle in disc If disc is not with multi-language/subtitle, it cannot
switch language/subtitle
No image Other factors cause MPU wrong operation Press [RES] button on the panel by penpoint, then,
power on
Cannot watch image
during driving It’s not allowed to watch image during driving
Check fuse
Remove disc before inserting another one
Park the car in a safe place, put the car stall in “ P ”
postion, pull up the hand brake, parking brake wire
must be grounded
Lens is dirty
Touch calibration
If touch calibration error occurs, you can adjust the touch coordinate by “Touch calibration”.
Click icon on setup interface, input password [888888] to confirm to access touch calibration interface, as shown in below diagram:
Touching methods
Use touch pen to click the center of “+” icon, and move along with center of “+” icon so as to calibrate the screen. It shall automatically
save data and exit after screen calibration.
Please accurately click all positions on screen, or the accuracy of touch calibration shall be affected.
CONTENTS
01
13 02
Steering wheel setting
1. Click icon on setup interface so as to access steering wheel setting interface (PIC 4).
2. Connect anode and cathode of direction control wire of the car with anode and cathode of
direction control wire of this device, and press the buttons on steering wheel one by one and record
the corresponding sequence and functions.
3. Click the button of steering wheel needs to be allotted so as to select the corresponding setting
function, such as volume +.
4. Buttons on steering wheel shall display the corresponding functions, such as volume +.
To modify function settings, repeat procedures 3~4.
To reset functions, click [Reset] icon, all the settings set before shall be cleared, repeat procedures 3~4 for resetting.
Language
During use, you can select your familiar language to display menu by language setup.
setting
Click icon on setup interface to access language setting interface, as shown in right (PIC 1) diagram:
Click the corresponding [English] icon on the language bar desired to be set so as to switch the
language type, when there are more than 3 languages, direction icon shall pop up, click it to select
your familiar language.
Audio setting
Click icon on setup interface to access audio setting interface, as shown in right (PIC 2) diagram:
You can turn on or turn off the existing functions on audio setting interface and adjust the rearview
volume.
Video setting
Click icon on setup interface to access video setting interface, as shown in right (PIC 3) diagram:
At video setting interface, you can adjust brightness, contrast, saturation and hue of the video.
Panel Introduction
1
4 5 6 7 8 11 12 13
14
109
18
19
32
15
16
17
1. /OPEN button
When power is turned on, long press the button to turn the unit
on/off. In any mode, press the button can switch to the main
interface. Press this button to open /close the screen.
2.
In radio mode, long press the button can scan station
automatically. Short press to fine tune station.
In playback mode, long press the button to speed backward, short
press to select previous song.
3.
In radio mode, long press the button can scan station automatically.
Short press to fine tune station.
In playback mode, long press the button to speed forward, short
press to select next song.
4. REL (Panel release button)
Press this button to release the panel.
5. MODE button
Press this button for a short moment to turn on power. Every
button-press activates mode change as follows: RADIO DVD→ →
USB (Optional) SD (Optional) AUX BT (Optional) RADIO→ → → →
Note: When the device without connection to USB, SD or DVD no
disc inside, the system will automatically skip these related
working mode.
6.VOL/SEL button
Repeat pressing this button can select the VOL, BAS, TRE, BAL,
FAD adjustment mode, Then can rotate the button to adjust VOL,
BAS, TRE, BAL, FAD as your likes.
7. MUTE/TFT-OFF (Enable mute function)
Press this button to turn off volume output, press it again to restore
the previous volume level.
Long press it to turn off TFT screen, and short press it so that TFT
screen shall be re-lit after turned off.


Produktspezifikationen

Marke: XOMAX
Kategorie: Nicht kategorisiert
Modell: XM-DTSB912

Brauchst du Hilfe?

Wenn Sie Hilfe mit XOMAX XM-DTSB912 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert XOMAX

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung fĂĽr -Kategorien-