Walrus Audio Fable Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Walrus Audio Fable (5 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 23 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/5
*The use of an isolated power supply is recommended for powering all Walrus Audio Pedals.
Daisy chain power supplies are not recommended.
Got questions or need a repair?
Email help@walrusaudio.com to talk with a real live human about your Walrus gear!
This product comes with a limited lifetime warranty.
Click Here for more info.
In the high woodlands of the north, undiscovered by most inhabitants, there ruled a clan of old,
mystic Treefolk. On the rst new moon of spring, these Treefolk could be heard grafting limbs
to grow their young - splicing bits of branches from each generation to produce the next line
of Treefolk. These new beings keep the lifeblood of all who came before in their new skin. These
sounds are in part very old but in part very new. They are referred to as… Fable.
9 volt DC, Center Negative • 300mA min*
Feedback: Controls the amount of gain in the first
feedback path.
Regen (Regeneration): Controls the amount of gain in the
second feedback path.
Mod (Modulation): Controls the amount of modulation
applied to the wet signal. Hold down bypass to adjust the
modulation rate with the Mod knob. You’ll see the bypass
LED flashing at the mod rate when this is active. Release
bypass when it’s at the desired rate and the pedal will
remember the setting.
Mix: Controls the amount of wet/dry mix.
Fully left = dry.
Fully right = wet.
CONTROLS
X: The X knob controls grain size (chopped sample length)
of the granular effects. Turn left for long, smooth sampling,
and turn right for short, choppy grains. On program 5 this
will also affect the rate at which the pitch shift changes in
the granular process.
Time: Controls the delay time and the granular buffer size
(length of the buffer from which grains are sampled).
Tone: Controls filtering of the output signal and feedback
loops. A synth style low-pass filter on the output sweeps
the full frequency spectrum from deep underwater lows to
light high-frequency roll-off, with slight resonance added
for an extra satisfying control response. At the top of the
control range a subtle high-pass filter is introduced into
the feedback paths, great for dialing in glassy repeats and
breathy ambient clouds.
Trails: The Fable can run in Trails or No Trails mode. In trails
mode, when you turn the pedal off, the reverb / feedback
decay dies off naturally. In No Trails mode, the decay is
abruptly cut off when you turn the pedal off. The Fable ships
with Trails mode on.
To toggle between either Trails mode:
1. Hold down the bypass switch while applying power
to the pedal.
2. After approximately four seconds the tap LED will
rapidly blink for 1 second confirming you have
changed trails modes.
3. A rapid green LED confirms you are in Trails mode.
A rapid red LED confirms you are in No Trails mode.
4. Repeat the process to changes modes again.
Tap Tempo: Tap to control the time
knob parameters:
Programs 1, 2, 3, 5 – Control delay
time and size of the granular buffer
(both set to tapped rate)
Program 4 – Control time stretching
of the multi-tap granular programs.
Dive / Rise: Holding down the tap tempo switch will momentarily shift the
clock rate of the pedal down or up and will hold it at that rate for as long as
the switch is pressed. The direction of the dive can be changed by simply
pressing bypass and tap simultaneously. A green LED over tap will indicate
Rise is set and a blue LED will indicate that Dive is set.
Forward Delay into Octave Up Granular
Program 2 runs a forward delay into an octave-up granular program, in which
sampled grains are played at double speed. Swarms of double-speed grains
build up in the feedback path for bright and airy cascades of sound.
PROGRAM SPECIFIC CONTROLS -
Feedback: Controls the amount of delay repeats.
Time: Controls the delay time and the granular buffer size (length of the buffer
from which grains are sampled)
Tap: Control delay time and size of the granular buffer (both set to tapped rate).
PROGRAM TWO
Reverse Delay Into Reverse Granular
Program 1 runs a reverse delay into a reverse granular algorithm, in which
sampled grains are played backwards. Reversal and re-reversal build up in the
feedback paths, creating a complex and organically shifting soundscape. Turn
grain size (X knob) down for long, smooth reversed transients, and grain size up
for stuttering reverse glitch madness.
PROGRAM SPECIFIC CONTROLS -
Feedback: Controls the amount of delay repeats.
Time: Controls the delay time and the granular buffer size (length of the buffer
from which grains are sampled)
Tap: Control delay time and size of the granular buffer (both set to tapped rate).
The Fable employs two analog feedback paths
which allow each program to incorporate a
unique mix of affected and unaffected feedback.
The two feedback paths interact and build off of
each other organically, offering the user a wide
array of sounds and behaviors to experiment with.
PROGRAM ONE


Produktspezifikationen

Marke: Walrus Audio
Kategorie: Nicht kategorisiert
Modell: Fable

Brauchst du Hilfe?

Wenn Sie Hilfe mit Walrus Audio Fable benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Walrus Audio

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-