Vermeiren Controleunit DX2 Basic Bedienungsanleitung
Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr Vermeiren Controleunit DX2 Basic (20 Seiten) in der Kategorie Rolle. Dieser Bedienungsanleitung war fĂĽr 41 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/20
VERMEIREN
DX2 Basic: without LCDscreen
DX2 with LCD screen
I N S T R U C T I O N M A N U A L
DX2 Operator control
vD - 2013-04
1
OPERATOR CONTROL DX2
1. Use
The operator control built into your electric wheelchair enables you to control all the driving,
steering, braking and operating processes and to control other adjusting motors (lifting
column, seat and back adjuster). The wheelchair's electrical unit and electronics are
constantly being monitored internally. Any fault in the electronics is indicated on the
operating display (6) and the status display (1) and, if necessary, the wheelchair may be
switched off for reasons of safety (see the chapter on fault analysis).
Vermeiren is responsible for the changes in the software. For changes in the software
contact Vermeiren.
The DX2 system is available in two different operator controls (DX2 Basic; DX2 with LCD
screen) which have some different operating buttons.
1
2
34
5
6
7
89
10
1 = Display
2 = "ON / OFF" button
3 = "Left indicator" + "Light" button
4 = "Right indicator" + "Warning
indicator" button
5 = "Horn" button
6 = Fault code/operating display
7 = Brightness sensor
8 = "Drive profile" button
9 = "Select field" button
10 = Max speed reduction
With LCD screen
1 = "ON / OFF" button
2 = Battery charge
indicator
3 = Speed switch
"-" : slower
"+" : faster
4 = Speed indicator
5 = "Horn" button
6 = Light sensor*
7 = Lock Led
8 = Left indicator
9 = Right indicator
10 = Left indicator LED
11 = Right indicator LED
12 = Adjustment Actuator LEDs
13 = Adjustment Actuator
selection
"-": down
"+": up
14 = Warning indicator
15 = Lights
16 = Attendant profile LED
17 = Fault indicator LED
18 = LED side lights
DX2 Basic:
Without LCD
screen
* The light sensor dims the display when it is dark
2
1
10
3
4
5
6
8
14
16
17
18
15
13
12
9
7
11
DX2 Operator control
vD - 2013-04
2
1.1. DX2 without LCD screen
Press the "ON/OFF" button (1). The charge indicator (2), which also indicates the batteries' charge
level, lights up for a moment. If all the lights come on, the batteries are sufficiently charged. If the lights
do not all come on, you must adjust your driving activities to suit the low capacity of the batteries. If the
battery charger display lights do not come on, check the plug connections of the electronic system.
Now select the driving program you want by pressing the speed switch (3), (-) symbol to go slower and
(+) symbol to go faster.
The selected speed is showed with the speed indicator (4). If you have any special needs, you can
ask your dealer to enter a personalised driving program.
To set the wheelchair in motion, push the joystick forwards slowly. The speed will increase when you
push the joystick further forwards. If you want to turn left or right, simply push the joystick in the
desired direction. To reverse, pull the joystick backwards from the central position.
L
Note that, when pressing the "ON/OFF" button, the joystick stays in the central position for at
least two seconds. It is programmed this way for technical and safety reasons, to prevent the
joystick being pushed at the same time as the wheelchair is being switched on. If both
processes are activated at the same time, the steering unit locks itself and can only become
operational again after being switched off completely.
Press the “Left indicator” (10) or “Right indicator” (11) buttons to signal a change in your driving
direction. The driving lights are switched on or off by pressing the “Lights” (15) button. You can sound
an acoustic warning signal with the “Horn” (5) button. The hazard warning lights, used in critical
situations, can be switched on or off by pressing the “Hazard warning lights” (14) button.
To brake while driving, simply push the joystick to its central position. Move the joystick slowly for
gradual braking. Simply release the lever for a quick stop; the wheelchair will then stop as quickly as
possible.
To activate the back adjuster, select button (13) until the corresponding number for the backrest
adjustment actuator lights up, and you can then use the joystick to tilt the back in the direction you
want.
To activate the seat incliner, select button (13) until the corresponding number for the seat adjustment
actuator lights up, and you can then use the joystick to incline the seat in the direction you want.
Turn wheelchair On/Off
In case of an emergency, you can use the On/off button to turn your wheelchair off.
Turn the power on:
Press the On/Off button. All LEDs of the battery indicator turn on simultaneously
and the fault indicator flash twice.
If the wheelchair is turned on while the joystick is out of neutral, an fault will be displayed on the
battery charge indicator (the five drive profile LEDs flash continuously and the chair will not drive).
Release the joystick back to neutral and the fault will disappear. If the joystick is not released
back to neutral (centre) within 4 seconds, the fault becomes a Module fault (the drive profile LEDs
+ fault indicator are flashing). To clear this fault, turn the DX system off and then turn it back on.
Turn the power off:
Press the On/Off button. All LED's will goe out. If the ON/OFF button is pressed
while driving the wheelchair perform an emergency stop and it turns off.
Produktspezifikationen
| Marke: | Vermeiren |
| Kategorie: | Rolle |
| Modell: | Controleunit DX2 Basic |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Vermeiren Controleunit DX2 Basic benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Rolle Vermeiren
1 Mai 2023
1 Mai 2023
1 Mai 2023
1 Mai 2023
1 Mai 2023
1 Mai 2023
1 Mai 2023
1 Mai 2023
Bedienungsanleitung Rolle
- Rolle Yamaha
- Rolle XD Enjoy
- Rolle Denver
- Rolle Sharp
- Rolle Telestar
- Rolle Nilox
- Rolle Xiaomi
- Rolle Lamax
- Rolle Prixton
- Rolle Peugeot
- Rolle Sencor
- Rolle Saro
- Rolle Kymco
- Rolle Razer
- Rolle Honda
- Rolle Aprilia
- Rolle Ducati
- Rolle SXT
- Rolle Be Cool
- Rolle Lionelo
- Rolle Batavus
- Rolle Benelli
- Rolle Keeway
- Rolle Matador
- Rolle Niu
- Rolle Sachs
- Rolle SYM
- Rolle Vespa
- Rolle Hudora
- Rolle Puky
- Rolle Kaabo
- Rolle Gilera
- Rolle Segway
- Rolle Hero
- Rolle Joyor
- Rolle TGB
- Rolle Derbi
- Rolle EVO
- Rolle INCA
- Rolle Little Tikes
- Rolle Piaggio
- Rolle E-way
- Rolle Razor
- Rolle Hyosung
- Rolle EMG
- Rolle Genuine
- Rolle Alpha
- Rolle Valk
- Rolle Root Industries
- Rolle InMotion
- Rolle Bintelli
- Rolle Mash
- Rolle Rolektro
- Rolle Bullet
- Rolle Hover-1
- Rolle Kugoo
- Rolle BOHLT
- Rolle Baotian
- Rolle Motus
- Rolle VR46
- Rolle Urban Glide
Neueste Bedienungsanleitung fĂĽr -Kategorien-
25 Juni 2024
23 Juni 2024
10 Juni 2024
9 Juni 2024
6 Juni 2024
6 Juni 2024
6 Juni 2024
1 Juni 2024
24 Mai 2024
24 Mai 2024