Vermeiren Carpo 2 Bedienungsanleitung
Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr Vermeiren Carpo 2 (35 Seiten) in der Kategorie Rolle. Dieser Bedienungsanleitung war fĂĽr 19 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/35
LCD screen
vE - 2015-10
1
LCD screen
1. Use
The LCD screen built into your scooter enables you to control all the driving, steering, braking and
operating processes. The scooters electrical unit and electronics are constantly being monitored
internally. Any fault in the electronics is indicated on the operator panel and, if necessary, the scooter
may be switched off for reasons of safety (see the "Error codes" section).
Vermeiren is responsible for the changes in the software. For changes in the software contact
Vermeiren.
Put the ON/OFF key switch on, please wait for at least 3 seconds before you press the speed lever
otherwise you have a “delay protection” alarm.
Now the LCD screen will light up.
Using battery charge indicator
The battery charge indicator is used to indicate that your scooter power is on
and provides an estimate of the remaining battery capacity.
1 = Trouble indicator
2 = MODE button
3 = Reverse switch (press 3
seconds)
4 = SET button
5 = Speed control (slow)
6 = Speed switch
7 = Speed control (fast)
8 = Head Lights
9 = Horn
10 = Indicator (left)
11 = Emergency lights
12 = Indicator (right)
13 = Battery level indicator
14 = Battery charger
connected
13
1
2 3 4
5
6
7
8 9
10 11 12
14
LCD screen
vE - 2015-10
2
Adjusting the Driving Speed
Now put the speed to the desired driving speed. The driving speed is a specific drive setting (slow or
fast, indoors or outdoors) that your therapist or dealer can adjust to suit your personal needs and
preference.
These speed shall be remembered after switching the scooter OFF and ON.
Press the button to decrease the drive speed: slow.
Press the button to increase the drive speed: fast.
The driving speed bar is showned on the LCD screen to indicate the driving
speed.
The speed can be set to low or high with the L/H button. Standard setting is
H (High), press the button to switch to L (Low). Switch the scooter OFF and
ON the Low / High speed shall not be remebered and automatically goes
back to the standard value H (High). H or L is shown on the LCD screen to
indicate which value is selected.
Reversing switch
Reversing switch. The default status is pull the right speed lever towards
you, scooter will go forward. Pull the left speed lever towards you, scooter
will go backward. Press the button for 3 seconds to switch the driving
direction. Pull the right speed lever towards you, scooter will go backwards.
Pull the left speed lever towards you, scooter will go forward. The button
turns green and the sign of two arrows is showed on the LCD screen. If
you switch the scooter OFF and ON the last setting shall be remembered.
While driving backwards with the scooter there shall be a sound from a
horn.
Using the horn
Press the horn button. The horn shall sound as long as the button is
pressed.
Button slow
Button fast
Button
LCD
Reversing Button
LCD
LCD
LCD screen
vE - 2015-10
3
Using the lights
1. Headlights:
To put on the front and back lights, press the light button, button
will turn green. Press again to turn the lights off.
The LCD screen shown a light symbol to indicate the lights are
activated.
2. Left and Right indicator lights:
To put on the indicator lights, press the desired button (left = left
indicator, right = right indicator). At the same time the button will
turn green and has a sound from a horn. Press the Button again
to turn the indicator off.
On the LCD screen a flashing arrow symbol left OR right is
shown to indicate the left or right indicator light is activated.
3. Hazard warning lights:
To put on the emergency lights, press the triangle button, at the
same time the button will flash red and the indicator lights buttons
turn green.
If one light is damaged, the triangle button will blink red.
On the LCD screen a flashing arrow symbol left AND right is
shown to indicate the hazard lights are activated.
To stop the scooter loosen the speed lever under the operator control.
Light button
LCD
Left indicator button
Right indicator button
LCD
Hazard lights button
LCD
Produktspezifikationen
| Marke: | Vermeiren |
| Kategorie: | Rolle |
| Modell: | Carpo 2 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Vermeiren Carpo 2 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Rolle Vermeiren
1 Mai 2023
1 Mai 2023
1 Mai 2023
1 Mai 2023
1 Mai 2023
1 Mai 2023
1 Mai 2023
1 Mai 2023
Bedienungsanleitung Rolle
- Rolle Yamaha
- Rolle XD Enjoy
- Rolle Denver
- Rolle Sharp
- Rolle Telestar
- Rolle Nilox
- Rolle Xiaomi
- Rolle Lamax
- Rolle Prixton
- Rolle Peugeot
- Rolle Sencor
- Rolle Saro
- Rolle Kymco
- Rolle Razer
- Rolle Honda
- Rolle Aprilia
- Rolle Ducati
- Rolle SXT
- Rolle Be Cool
- Rolle Lionelo
- Rolle Batavus
- Rolle Benelli
- Rolle Keeway
- Rolle Matador
- Rolle Niu
- Rolle Sachs
- Rolle SYM
- Rolle Vespa
- Rolle Hudora
- Rolle Puky
- Rolle Kaabo
- Rolle Gilera
- Rolle Segway
- Rolle Hero
- Rolle Joyor
- Rolle TGB
- Rolle Derbi
- Rolle EVO
- Rolle INCA
- Rolle Little Tikes
- Rolle Piaggio
- Rolle E-way
- Rolle Razor
- Rolle Hyosung
- Rolle EMG
- Rolle Genuine
- Rolle Alpha
- Rolle Valk
- Rolle Root Industries
- Rolle InMotion
- Rolle Bintelli
- Rolle Mash
- Rolle Rolektro
- Rolle Bullet
- Rolle Hover-1
- Rolle Kugoo
- Rolle BOHLT
- Rolle Baotian
- Rolle Motus
- Rolle VR46
- Rolle Urban Glide
Neueste Bedienungsanleitung fĂĽr -Kategorien-
25 Juni 2024
23 Juni 2024
10 Juni 2024
9 Juni 2024
6 Juni 2024
6 Juni 2024
6 Juni 2024
1 Juni 2024
24 Mai 2024
24 Mai 2024