Thorma Granada Bedienungsanleitung

Thorma Herd Granada

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Thorma Granada (16 Seiten) in der Kategorie Herd. Dieser Bedienungsanleitung war für 11 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/16

ZARAGOZA, GRANADA

Installation and Operation Manual

solid fuel heater

ZARAGOZA, ZARAGOZA Plus, GRANADA

tested according to the standard EN 13240

1. Installation Instruction

The heater has been designed to allow simple connection to an existing chimney by a single connecting piece. The connecting

piece must be as short and straight as possible, in a horizontal position or slightly inclined. The piece must be tight.

Be sure that all local regulations, including those concerning both national and European standards on construction and fire

prevention, are respected during installation. Inform the competent inspector prior to installation. Be sure that combustion air supply

is sufficient; particularly in rooms where windows and doors are closed tight.

Chimney properties shall be calculated in accordance with DIN 4705 parts 1 and parts 2, eventually also part 3, with the three

values stated in this manual.

The heater must stand on a hearth with adequate bearing capacity. If bearing capacity is too low, adequate measures must be

taken (e.g. a board must be laid to split weight).

Into the heater can be mounted fireproof concrete stones which accumulate heat their ability to keep the heater warm surface many

hours after burning out of fuel. Examples of position of the stones are on page No. 16. Stones are marked with dark colour.

2. General Safety Instructions

Fuel combustion emits calorific energy that heats the surface of the heater, combustion chamber door, door and control elements

handles, safety glass, flue pipes, and eventually also the front of the heater. Do never touch those parts without adequate safety

wear or elements (fireproof gloves etc.).

Warn children of such danger and make sure they do not stay close to heater when in operation.

3. Acceptable Fuel

Fuels acceptable for burning include wood logs of up to 25 cm in length and 30 cm in circumference, and lignite briquettes.

Make sure that only air dried wood logs are used. Burning of waste, and plastics in particular, is forbidden by law on emissions.

Besides, such fuel may cause damage to the fire place and chimney and subsequently may injure health and smell may annoy your

neighbours. Air dried wood logs with 20% maximum humidity may be obtained after at least one year (soft wood) or two years (hard

wood) of drying.

Wood is not slow combustion fuel and thus, continuous heating throughout the night is not possible when burning wood.

Liquid fuel is unacceptable.

4. Firing

During the first firing bad smell due to drying of protection paint is inevitable but the smell shall fade quickly. Make sure the room

with the heater is well aerated when firing. Quick firing is essential because incorrect procedure may cause increased emissions.

Add more fuel as soon as firing fuel catches fire. Do never use alcohol, petrol or other flammable liquids for firing. Do always use

some paper, wood chips, and a small amount of fuel for that. Make sure that primary and secondary air is supplied to heater when

firing. Make sure that heater is under control during firing.

5. Operating More than One Fireplace

Make sure that combustion air supply is sufficient when operating more than one fireplace in one room or within the same air system.

6. Transition Season Operation

When exterior temperature rise during transition season draught can decrease at low burning capacity and flue gas may not be

evacuated completely. In such case add only small quantities of fuel and open the slider of primary air supply so that loaded fuel

burns more quickly (flame) and draught gets steady. Ash needs to be raked carefully more often to enhance air circulation below

fireplace.

7. Cleaning and Checking

Heater flue pipes need to be checked for deposit and eventually swept at least once a year or more often, e.g. while sweeping

chimney. Make sure your chimney is swept regularly by a chimneysweep. The frequency of sweeping shall be defined by

competent inspector. Heater should be checked by an expert every year. It is forbidden to clean the heater with a damp cloth.

8. Versions

Heaters with spring fireplace door can be connected to a chimney with multiple taking for other heaters and fireplaces provided that

dimensions of the chimney are in compliance with DIN 4705 part 3.

The door of the heater with spring fireplace door must always be closed during operation, except for firing, fuel charging, and ash

removing. Otherwise operation of other equipments connected to the chimney may be affected or flue gas may leak.

9. Combustion Air

Since heaters are fireplaces depending on surrounding air and take combustion air from the room, adequate intake of combustion

air is vital.

In rooms with tight windows and doors (e.g. as energy-saving measure) fresh air intake may be low and thus affect draught of the

heater. Also your well-being may be affected; even your safety may be threatened. It may sometimes be necessary to assure

adequate intake of fresh air e.g. by installing air shutter close to heater or by combustion air pipe leading to exterior or to a well

aerated room (except boiler room). In particular it is vital that combustion air pipes are open during operation of fireplace. Steam

ZARAGOZA, GRANADA

flues located in the same room with fireplace may affect heater’s operation (smoke may leak to inhabited room despite closed

fireplace door) and therefore must never be operated parallely with the heater.

The outdoor combustion air could be supplied to the heater through the connecting socket which can be mounted on the bottom of

the backside of the heater.

10. Fire Protection

Distance from flammable structures and furniture

To assure adequate heat protection, a minimum distance of 15 cm in the back and 15 cm on the sides is required between the

heater and flammable structures and furniture.

Fire protection within radiation perimeter

Make sure that no flammable structures or furniture are within radiation perimeter of glass door, which is 80 cm. The distance may

be reduced to 40 cm if safety shade is installed between fireplace and flammable structures leaving enough space on both sides.

Fire protection outside radiation perimeter

Minimum distances from flammable structures and furniture are stated on heater’s label and must be observed.

Heater

For solid fuel heaters floor in front of fireplace’s door made of flammable materials must be protected by a non-flammable hearth.

Its minimum dimensions are 50 cm in the front and 30 cm on the sides of fireplace door.

11. Spare Parts

Only spare parts approved or provided by the manufacturer may be used. For inquiries, please, contact a specialized vendor.

No modifications to heater are allowed!

12. Warning in case of fire in chimney

Deposit in chimney may catch fire if unsuitable or humid fuel is used. In such case close all heater air holes immediately and call

the fire brigade. After fire is extinguished chimney should be inspected by an expert for cracks or untight places.

13. Nominal heating capacity, combustion air adjustment, and fuel burning time

Nominal heating capacity of heater is 5,0 kW and it is obtained at minimum supply pressure of 10 Pa for wood and 12 Pa for lignite

briquettes.

Fuel

Wood logs (25 cm length, 30 cm circumference)

Lignite briquettes

Maximum dose

1,9 kg

1,2 kg

Slider

pull out 5 mm

pull out completely

Burning time

1.0 hour

When burning wood, set the slider (pull out to 5 mm) so that the primary combustion air intake is completely closed and

the secondary combustion air intake is 5 mm open.

When burning lignite briquettes set the slider (pull out completely) so that both primary and secondary air intakes are fully open.

The combustion air slider is below the firing door.

Quantity and adjustment of combustion air for moderate operation:

Fuel

Lignite briquettes

Maximum dose

1,2 kg

Slider

pull out 5 mm

Burning time

approx. 2 hours

14. Space Heating Capacity

For rooms with insulation non-conform with calorific insulation regulations space heating capacity should be determined pursuant to

DIN 18 893 for nominal heating capacity of 5,0 kW:

in favourable heating conditions - 124 m3

in poor heating conditions - 73 m3

in unfavourable heating conditions - 48 m3

For occasional heating – interrupted for more than 8 hours – space heating capacity is reduced by 25%.

15. Technical Data

Capacity: 5,0 kW

Weight: ZARAGOZA = 91 kg, ZARAGOZA Plus = 133 kg, GRANADA with accumulation stones = 130 kg

Upper flue gas outlet: 150 mm

Data for chimney properties calculation (at nominal heating capacity):

Fuel

Wood logs

Lignite briquettes

Flue gas flow [gs-1]

5,9

6,1

Average temperature of flue after draught shaft [°C]

272

277

Min. draught at nominal heating capacity [Pa]

ZARAGOZA, GRANADA

Guarantee

Shall any failure, malfunction, or surface defect occur on your heater within the guarantee period do never repair it by yourself. After-sale service

can be done only by the manufacturer or distributor.

We guarantee the quality, function, and construction of the heater for 2 years from the day of purchase: defects definitely occurred as a

consequence of manufacturing defect will be remedied within short time at our cost under the condition that the heater:

- has been operated in conformity with operating instruction,

- has been connected to the chimney in conformity with applicable standards,

- has not been damaged mechanically by force,

- has not been subject to modifications, repairs and incompetent handling.

When making a complaint give your exact address and circumstances when the dysfunction occurred. We will deal with the complaint if you

deliver the warranty certificate with the date of purchase and the sales point stamp along with the complaint.

Ask for legible warranty certificate at purchase. Our company will decide on method and place of reparation to be carried out.

Upon purchase, check for integrity of the firing door glass. This is under guarantee for 15 days after the purchase.

It is unacceptable to operate the appliance at extreme conditions, which means:

- fuel quantity exceeds the recommended quantity,

- air supply exceeds the recommended quantity,

- unacceptable fuel types are used.

Heat overcharge shows in the following ways:

- fireplace ceiling deflection,

- firing door damage

- grille has burnt over,

- vermiculittes have cracked,

- change of colour tone of the heater surface

The complaint will not be accepted by the manufacturer if the appliance has not been operated correctly.

Exchange of the product or making the purchase contract void is subject to applicable dispositions of the Civil Code and the

Complaints Order.

Aufstell - und bedienungsanleitung für den

Kaminofen ZARAGOZA, ZARAGOZA Plus, GRANADA

geprüft nach DIN EN 13240, § 15a B-VG, 2. Stufe 1.BImSchV

1. Aufstellhinweise

Der Kaminofen ist anschlussfertig montiert und muss mit einem Verbindungsstück an den bestehenden Hausschornstein

angeschlossen werden. Das Verbindungsstück soll möglichst kurz, geradlinig, waagerecht oder leicht steigend angeordnet sein.

Verbindungen sind abzudichten.

Nationale und Europäische Normen, örtliche und baurechtliche Vorschriften sowie feuerpolizeiliche Bestimmungen sind

einzuhalten. Informieren Sie daher vorher Ihren

Bezirks-Schornsteinfegermeister. Es ist sicherzustellen, dass die für die Verbrennung benötigte Luftmenge ausreichend ist. Hierauf

ist besonders bei dichtschließenden Fenstern und Türen (Dichtlippe) zu achten.

Die Schornsteinberechnung erfolgt nach DIN EN 13384 – 1 bzw. 13384 - 2 mit dem dieser Anleitung zugefügten Wertetripel.

Prüfen Sie vor dem Aufstellen, ob die Tragfähigkeit der Unterkonstruktion dem Gewicht Ihres Kaminofens standhält. Bei

unzureichender Tragfähigkeit müssen geeignete Maßnahmen (z. B. Platte zur Lastverteilung) getroffen werden, um diese zu

erreichen.

An die Kaminöfen können Speichersteine eingebaut werden, die sich durch ihre Kumulationsfähigkeit auszeichnen, die Oberfläche

der Dauerbrandöfen für mehrere Stunden nach dem Ausbrennen des Brennstoffes warm zu halten. Die Einbaubeispiele der

Speichersteine finden Sie an Seite 16. Steine sind mit dunklen Farbe markiert.

2. Allgemeine Sicherheitshinweise

Durch den Abbrand von Brennmaterial wird Wärmeenergie frei, die zu einer starken Erhitzung der Oberflächen, der

Feuerraumtüren, der Tür- und Bediengriffe, der Sichtfensterscheibe, der Rauchrohe und ggf. der Frontwand des Ofens führt. Die

Berührung dieser Teile ohne entsprechende Schutzbekleidung oder Hilfsmittel (hitzebeständige Handschuhe oder andere

Betätigungsmittel) ist zu unterlassen.

Machen Sie Kinder auf diese Gefahren aufmerksam und halten Sie sie während des Heizbetriebes von der Feuerstätte fern.

3. Zulässige Brennstoffe

Zulässige Brennstoffe sind Scheitholz mit einer Länge von 25 cm und einem Umfang von 30 cm sowie Braunkohlenbriketts.

Es darf nur lufttrockenes Scheitholz verwendet werden. Die Verfeuerung von Abfällen und insbesondere Kundstoff ist laut

Bundesimmisionschutzgesetz verboten. Darüber hinaus schadet dies der Feuerstätte und dem Schornstein und kann zu

Gesundheitschäden und aufgrund der Geruchsbelästigung zu Nachbarschaftsbeschwerden führen. Lufttrockenes Scheitholz mit

maximal 20% Wasser wird durch eine mindestens einjährige (Weichholz) bzw. zweijährige Trockenzeit (Hartholz) erreicht.

Holz ist kein Dauerbrand-Brennstoff, so dass ein Durchheizen der Feuerstätte mit Holz über Nacht nicht möglich ist.

Produktspezifikationen

Marke:	Thorma
Kategorie:	Herd
Modell:	Granada

Brauchst du Hilfe?

Wenn Sie Hilfe mit Thorma Granada benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Herd Thorma

Thorma Bozen Bedienungsanleitung

7 Juli 2024

Thorma Almeria Bedienungsanleitung

7 Juli 2024

Thorma Domino III Bedienungsanleitung

7 Juli 2024

Thorma Falun Bedienungsanleitung

7 Juli 2024

Thorma Domino II Bedienungsanleitung

7 Juli 2024

Thorma Horby Bedienungsanleitung

7 Juli 2024

Thorma Filex Eurofen II Bedienungsanleitung

7 Juli 2024

Thorma Loholm Bedienungsanleitung

7 Juli 2024

Thorma Mallorca Bedienungsanleitung

7 Juli 2024

Thorma Vigso III Bedienungsanleitung

7 Juli 2024

Bedienungsanleitung Herd

Neueste Bedienungsanleitung für -Kategorien-

Harvia 22 8 WK220SES Bedienungsanleitung

16 Oktober 2024

Zibro Kamin RCA 3000 F Bedienungsanleitung

13 Oktober 2024

Pelgrim IDK784 Bedienungsanleitung

8 Oktober 2024

Basetech BT-2268546 Bedienungsanleitung

6 Oktober 2024

Livin Flame EVO Remote - Wi-Fi Module Bedienungsanleitung

5 Oktober 2024

Spartherm Passo S Bedienungsanleitung

5 Oktober 2024

Nestor Martin TFH33 Bedienungsanleitung

5 Oktober 2024

Livin Flame Build in burners Bedienungsanleitung

5 Oktober 2024

Livin Flame Karlstad Bedienungsanleitung

5 Oktober 2024

AEG BSS577121M Bedienungsanleitung

4 Oktober 2024