Techly I-WL-CPE880 Bedienungsanleitung

Techly Zugangspunkt I-WL-CPE880

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Techly I-WL-CPE880 (2 Seiten) in der Kategorie Zugangspunkt. Dieser Bedienungsanleitung war für 12 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/2

WWW.TECHLY.COM WWW.TECHLY.COM WWW.TECHLY.COM WWW.TECHLY.COM

EN User’s Manual

Place the CPE to the

selected position and

adjust the CPE front

panel orientation to be

approximately the same

as the selected direction.

Connect the PoE adapter’s

LAN to PC, Router or Switch

based on the network

topology.

Please prepare a long

enough network cable to

connect the POE adapter

and CPE. Recommend to

use a Category 5E (or

above) shielded network

cable with a ground wire.

Completed connection, push up to restore the

CPE back cover.

Point to multiple point Point to Point

In the wireless monitoring

transmission, it is recommended to

use the above graphic method for

point-to-point or point-to-multi-

point transmission.

The wireless bridge/outdoor CPE

transmission angle is oriented at

60 degrees. Please adjust the

equipment’s angle when building

point-to-multi-point transmission.

Check the local network connection

Set Static IP address for PC

P/N: I-WL-CPE80

8051128108453

P/N: I-WL-CPE120

8051128108446

P/N: I-WL-CPE880

8051128108439

POINT-TO-POINT CPE

S M

IP Camera

IP Camera IP Camera

IP Camera

Repeater

Repeater Repeater

Monitoring

DVR

Switch DVR

Wireless Network

Disable

Connect/Diconnect

Status

Diagnose

Bridge Connections

Create Shortcut

Delete

Rename

Properties

Device installation

Passive PoE Adapter supports up to 60 meters (200 feet) Power over Ethernet

deployment

Wireless Connection Topology LED Display CPE

1. Default working mode is Slave CPE or Client, IP: 192.168.2.1.

2. Set one CPE to Master CPE or Host, in LED Display will start with “H”:

Nota: F is function and confirm button;

S is setting button.

F (Press F button to choose the function need to set) - S (Press

S button to set the value like operation mode, channel) - F

(Press F button again to confirm the value, success after

blinking 5 seconds)

H--- Master CPE

060---channel 60

C--- Slave CPE

060--- channel 60

3. Master CPE channel must be same as Slave CPE:

4. Press Reset 1 second on both side, the two outdoor devices will start bridging:

(Nota: LED Display CPE will be finished in 2 minutes 20 seconds.)

Finish within 2’20’’

Press Reset on both side

at same time

Slave CPEMaster CPE

WEB Configuration

1. PC configuration if PC connect CPE by wireless

Set PC wireless network IP to 192.168.2.x (x: 2--250), same network segment as CPE, subnet mask:

255.255.255.0:

2. PC configuration if PC connect CPE wired

If connect PC and CPE wired, Set PC local network IP to 192.168.2.x (x: 2--250), same network segment

as CPE, subnet mask: 255.255.255.0:

Local Network Properties

Networking Sharing

Connect using:

Installl Uninstalll Propertie

Decription

Transmission Control Protocol/Internet Protocol.The default

widearea network protocol that provides communication

across diverse interconnected networks.

This connection uses the following items:

Client for Microsoft Networks

QoS Packet Scheduler

File and Printer Sharing for Microsoft Networks

Internet Protocol Version6(TCP/IPv6)

Internet Protocol Version4(TCP/IPv4)

Link-Layer Topology Discovery Mapper I/O Driver

Link-Layer Topology Discovery Responder

Realtek PCle GBE Family Controller

Configure...

OK Cancel OK

Advanced...

Cancel

Internet Protocol Version 4(TCP/IPv4) Properties

General

IP address:

Subnet mask:

Default gateway:

Use the following DNS server addresses:

Preferred DNS server:

Alternate DNS server:

Obtain an IP address automatically

You can get IP settings assigned automatically if your network supports

this capability.Otherwise,you need to ask your network administrator for

the appropriate IP settings.

Validate settings upon exit

19 2.1 68. 2. x

25 5.2 55. 25 5.0

. . .

Use the following IP address:

Obtain DNS server address automatically

After IP address configuration, connect to CPE’s wireless SSID: TECHLY5G

Local Network

yunlink 8

Realtek PCIe GBE Fam

Disable

Status

Diagnose

Bridge Connections

Create Shortcut

Delete

Rename

Properties

Local Network Properties

Networking Sharing

Connect using:

Installl Uninstalll Propertie

Decription

Transmission Control Protocol/Internet Protocol.The default

widearea network protocol that provides communication

across diverse interconnected networks.

This connection uses the following items:

Client for Microsoft Networks

QoS Packet Scheduler

File and Printer Sharing for Microsoft Networks

Internet Protocol Version6(TCP/IPv6)

Internet Protocol Version4(TCP/IPv4)

Link-Layer Topology Discovery Mapper I/O Driver

Link-Layer Topology Discovery Responder

Realtek PCle GBE Family Controller

Configure...

OK Cancel OK

Advanced...

Cancel

Internet Protocol Version 4(TCP/IPv4) Properties

General

IP address:

Subnet mask:

Default gateway:

Obtain DNS server address automatically

Use the following DNS server addresses:

Preferred DNS server:

Alternate DNS server:

Obtain an IP address automatically

You can get IP settings assigned automatically if your network supports

this capability.Otherwise,you need to ask your network administrator for

the appropriate IP settings.

Validate settings upon exit

19 2-1 68 .2. x

25 5.2 55. 25 5.0

. . .

Use the following IP address:

WWW.TECHLY.COM WWW.TECHLY.COM WWW.TECHLY.COM WWW.TECHLY.COM

Trouble Reason Solution

Packet

Latency

1. Wireless Interference

2. Distance is too long, or there are some

bar between them

3. CPE’s angle in wrong direction, weak signal

1. Use Wi-Fi analysis to choose the best

channel, or change to 5G CPE

2. CPE should be in normal distance, and

avoid bar

3. Adjust the angle of CPE according to signal

strength

Wrong

password

1. Forget password

2. Input wrong password

3. Too much cookie

1. Press reset button in 10 seconds to reset

device, the default password is admin

2. Re-input the password

3. Clear cookie, run arp -d to clear MAC table

Can not login

WEB

1. Local IP is not in the same network

segment of CPE

2. IP is taken by other devices

3. LAN Connection or Ethernet cable has

problem

4. Too much cookie, MAC address haven t ’

update

1. Ping 192.168.188.253 to see connection

status

2. Stop other devices or change to another IP

3. Check LAN Connection and Ethernet cable

4. Clear cookie, run arp -d to clear MAC

address

System LED

1. PoE power supply is not working

2. Some problem in CPE’s PoE port

3. Ethernet cable is loose, RJ45 port is wrong

Power current/voltage lower or wrong

1. Check if POE Adapter or POE switch work

2. Check if POE port of CPE is OK

3. Check if Ethernet cable is loose, if Ethernet

cable plugged in to POE port

4. Check if voltage is normal, if socket has

problem, if input voltage of POE adapter

is normal

Low

transmission

Rate

1. Packet Latency

2. Ethernet cable circuit

3. Network virus attack

4. Too much access users

1. Adjust the distance, angle and channel to

decrease latency

2. Check the connection of the network cable

3. Check if port isolated to avoid network virus

and broadcast storm

4. Decrease the access users

Device always

Dead

1. Static electricity

2. Running time too long

3. Lightning stroke

1. Make CPE or POE adapter need ground

connection

2. Reboot CPE device

3. After lightning, device POE port broken

or unstable, better to deploy lightning

conductor

POINT-TO-POINT CPE

TECHLY® - Viale Europa 33 - 33077 Sacile (PN) - Italy

3. 4. 5. Login Web Configuration Configure Wireless Login WEB by Mobile Phone

Using Setup Wizard the CPE device can be set up to Repeater and AP mode.

Use IE browser to access http://192.168.2.1, pop up the login page shown below, input

the login password: admin, enter into the home page.

• Repeat mode

Bridge the exist wireless signal then transmit Wi-Fi for more range.

• AP mode

In this mode, NAT, DHCP, firewall, and all WAN-related functions are turned off. All

wireless and wired interfaces are bridged together, regardless of LAN and WAN.

• Configuration method

According to the quickly setup wizard of each mode shown in the above figure, set

the parameters and options based on user needs, click next until the setting of each

step is completed.

a. Use a laptop or mobile phone to test the wireless network Internet, click on the

wireless network, select the wireless SSID, input the password to test whether PC

or mobile phone can be online.

b. Check the wireless network connection status, signal strength and speed, transmis-

sion and data, click network connection details to see if the IP address and DNS

server address are correctly obtained, confirm device is working properly.

1. Mobile phone connect with outdoor CPE, SSID:TECHLY5G

2. Configure static IP:

- Android Mobile Phone: Open settings in phone, turn on WLAN and find the SSID

of the CPE, access to wireless network settings then choose "static IP" in the menu,

set the mobile phone IP address as 192.168.2.x (x can not be 1) same network

segment as CPE, subnet mask: 255.255.255.0, then gateway, subnet mask and

domain.

- IOS Mobile Phone: Open settings and choose wi-fi connect with CPE, click

exlamation mark (!), manual set IP address 192.168.2.x (x can not be 1) same

network segment as CPE, subnet mask: 255.255.255.0, then gateway, subnet mask

and domain.

3. Input 192.168.2.1 on the internet explorer bar, input admin to login the mobile

configuration page.

Outdoor CPE supports mobile phone Login and set, the configure page showed as

follow:

Channel Table Trouble shooting

Wireless Bridge Regional Channel Code Instructions

(Note: for the frequencies above indicated the DFS function must be activated)

Setup Wizard

Homepage

Home

Wizard

CPE

WiFi

Network

Manage

Operation Mode Repeater Mode Flow WDS Down Stream WDS Up Stream

Device Location

Uptime:00:04:19

Device Information

CPU Usage

IP Mode Get IP From AC

Lan IP 192.168.188.253

Subnet 255.255.255.0

AC Address 192.168.188.1

MAC Address 44:D1:FA:4C:D8:AE

Memory Usage

LAN Information WDS Information WiFi Information

Encrypt Open

AP BSSID N/A

Status ON

SSID Wireless5.8G

Channel 44

Encrypt WPA/WPA2PSK_TKIPAES

MAC Addres 44:D1:FA:4C:D8:B0

Bandwidth Test

Network Connection Details

Property

Connection-specific DN...

Description

Physical Address

DHCP Enabled

IPv4 Subnet Mak

Lease Obtained

Leae Expires

IPv4 Default Gateway

IPv4 DHCP Server

IPv4 DNS Servers

IPv4 WINS Server

Net BIO over Tcpip En...

Link-local IPv6 Addres

IPv6 Default Gateway

Yes

Fe80 cb8:decO:56c1:94d%14：

Qualcomm Atheros AR956x Wireles

B8-86-87-3E-B5-3D

Yes

192.168.2.2

255.255.255.0

2018 7 28 9 57 23- - ：：

2018 7 28 10 57 22- - ：：

192.168.2.1

114.114.114.114

192.168.82.1

Value

Close Close

Wieless Network Status

General

Connection

IPv4 Connectivity:

IPv6 Connectivity:

Media State:

SSID:

Duration:

Speed:

Signal Quality:

Internet

No Internet access

Enabled

yunlink

01:01:21

72.2Mbps

Activity

Bytes:

Sent Received

Wireless PropertiesDetail...

Properties Disable DIagnoe

Super Intelligent

Working Mode: Super WDS

click to setup location information

running time 00:32:12

channel9

Setup Wizard System Status

More FunctionsWiFi Setup

WLAN

CONNECTED

yunlink 5.8G

Connected

yunlink

Saved

AVAILABLE NETWORKS

123456789

BDCOM-0000

BRCE 2.4G

BV_2_4G-200

BV_5_8G-200

400Mbps

None

192.168.2.2

255.255.255.0

192.168.2.1

Canel OKyunlink 5.8G Network details

IP settings

> DHCP

Static

Canel OKyunlink 5.8G Network details

Gateway

PROXY

IP SETTINGS

192.168.82.1

None >

Static >

192.168.2.2

192.168.2.1

8.8.8.8

8.8.4.4

IP address

Gateway

prefix length

DNS 1

DNS 2

Modify network

Forget network

Android system setup steps

Settings

Apple ID Suggestions

Airplane Mode

Wi-Fi

Bluetooth

Cellular

Personal Hotspot

VPN

Carrier

yunlink 5.8g

Off

CHINA MOBILE

Settings WI-FI

Wi-Fi

FR3800-X5-MESH-5.8G

Unsecured Network

CHOOSE A NETWORK...

BDCOM_0000

BV_2_4G-200

BV_5_8G-200

HP-Print-35-LaserJet Pro MFP

M1 5G test

NIS-HomeAP-5G_519C

szjk5

Wireless 2.4G-11111

Wireless 5.8g-22222

yunlink

Back Configure IPv4

Automatic

Manual

BootP

MANUAL IP

IP Address

Subnet Mask

Router

192.168.2.2

255.255.255.0

192.168.188.253

1 2 3 4 5 6 7 8 9 0

ABC

#+= . , ,

? !

space retur n

IOS system setup steps

Repeater Mode AP Mode

With the CE sign, Techly® ensures that the product is conformed to the

basic European standards and directives. The full text of the EU Declara-

tion of Conformity is available on the WWW.TECHLY.COM website in the

product page.

In compliance with EU Directive WEEE this product is marked with this

symbol. It means that used electrical and electronic products should not

be mixed with general household waste.

There is a separate collections system for these products in compliance

with WEEE directive, otherwise contaminative and hazardous substan-

ces can pollute the environment.

Regional Code 5G Channel

ETSI

5.500GHz (Channel 100)

5.520GHz (Channel 104)

5.540GHz (Channel 108)

5.560GHz (Channel 112)

5.580GHz (Channel 116)

5.600GHz (Channel 120)

5.620GHz (Channel 124)

5.640GHz (Channel 128)

5.660GHz (Channel 132)

5.680GHz (Channel 136)

5.700GHz (Channel 140)

Produktspezifikationen

Marke:	Techly
Kategorie:	Zugangspunkt
Modell:	I-WL-CPE880
Upgradefähige Firmware:	Ja
Breite:	90 mm
Tiefe:	38 mm
Gewicht:	646 g
Mitgelieferte Kabel:	LAN (RJ-45)
Produktfarbe:	Weiß
Höhe:	262 mm
Zweck:	Innen & Außen
Platzierung:	Wand
Gleichstrom-Anschluss (DC):	Ja
Antennentyp:	Intern
Betriebstemperatur:	-40 - 55 °C
Relative Luftfeuchtigkeit in Betrieb:	10 - 95 %
Montage:	Wand- / Mast
Netzstandard:	IEEE 802.11a, IEEE 802.11n, IEEE 802.3
Schnellstartübersicht:	Nein
Power over Ethernet (PoE):	Ja
Anzahl Ethernet-LAN-Anschlüsse (RJ-45):	1
Maximale Datenübertragungsrate:	300 Mbit/s
2,4 GHz:	Ja
WAN Port:	Ethernet (RJ-45)
Antenne Zunahmeniveau (max):	15 dBi
LED-Anzeigen:	LAN, Power, WAN, Wi-Fi
Temperaturbereich bei Lagerung:	-40 - 70 °C
Frequenzband:	5.8 GHz
Web-basiertes Management:	Ja
Nachhaltigkeitskonformität:	Ja
Nachhaltigkeitszertifikate:	CE
Eingangsstrom:	1 A
Reset-Knopf:	Ja
5 GHz:	Ja
Antennenfunktionen:	Integrierte Antenne
Empfängersensitivität:	802.11a: -70dbm @ 54Mbps; -90dBm @ 6Mbps
Polarisation:	Duale Polarisation
MIMO:	Ja
Syslog:	Ja
DC Spannungsrange:	12 V
Betriebsmodi:	AP / Repeater
6 GHz:	Nein