Tactical Fiber Systems CCRT241 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Tactical Fiber Systems CCRT241 (2 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 4 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/2
1525 NW 3rd Street, Deerî…•eld Beach, FL 33442 877-777-7147 www.TacticalFiber.com
TFS ClearCom/RTS 2 wire to 4 wire InterCom Interface - Mod.CCRT242
Installaon and Operang Instrucons with ATEM Studio Converter 2
Product Descripon
TFS's CCRT24 interface connects a 2 wire Clear-Com or RTS base staon to the Blackmagic ATEM Studio
Converter or Studio Converter 2 's four wire intercom system . The Clear-Com or RTS base staon
becomes the master intercom and communicates to both wired or wireless party line/matrix belt-paks
and the ATEM camera converters linked to the Studio Converter over î…•ber.
Installation
Connect the Clear-Com or RTS base staon to the CCRT24 interface using a 3PIN XLR cable from any
intercom output channel. NOTE: The CCRT24 is powered by the Clear-Com or RTS base staon.
Connect the ATEM Studio Converter to the CCRT24 interface using the interface cable designed for
STUDIO CONVERTER 2. (Note: The original STUDIO CONVERTER comes with a diî…’erent cable.) One end
has a 16 pin DIN connector which aaches to the CCRT24. The other end has two break-out cables for
connecon to the Studio Converter's Mic and Headset sockets. Insert the BLACK .20" connector plug
into the MIC input and the grey 1/4" TRS plug into the HEADSET sockets on the Studio Converter.
DIP Switch Positions
The dip switch sengs at the rear of the CCRT241 should be set as follows:
Switch 1 - (up) ON
Switch 2 - ClearCom - OFF (down) RTS -ON(up)
Calibrating the Interface
Your TFS CCRT24 Clear-Com/RTS interface was factory nulled with an MS-702 Clear-Com base staon
aached to a Blackmagic ATEM Studio Converter. You may have to tweak the null adjustments to match
your parcular Studio converter using an ear set and a small screwdriver. To null the interface, plug in
the ear set into the 1/8" jack to the right of the interface and adjust the RLC trim pots for minimum
noise...then unplug the ear set. IMPORTANT: You must unplug the ear set aî…³er nulling the interface
before using it. If you forget, you will hear lots of noise and it will not work. Also the yellow data light --
on the interface will blink repeatedly.
Controls and Operation
Atem Studio Converter Settings:
Turn all camera buttons 1 - 4 on. Buttons should turn blue. You must have all of them on for
intercom audio to pass between the ClearCom or RTS Base station.
ClearCom or RTS Base Station Settings: Termination settings for all intercom outputs should
be ON. On the ClearCom MS-702 or MS-704 base stations these switches are located on back. --
Local Send:
Controls the audio signal level from the Clear-Com/RTS 2 wire Com to the audio of the 4-out
wire I/O (headset). Adjust as required.
Local Receive:
Controls the audio signal level from the audio of the I/O to the local 2-wire intercom. in (mic)
Adjust as required.
Sidetone Null Adjustment:
This set of three trim-pots include R= Resistance, L= Inductance, and C= Capacitance. These
compensate for each component of the line impedance, providing the best null possible. To
prevent damage to the level control and nulling trim-pots, do not force them past their stop
points.
Power LED:
This green LED will illuminate when it is receiving power from pin 2 of the party-line XLR
connection.
Ear set Port
For Nulling
Local PL
Send
Recv
Data
R
On
C
L
4-Wire Interface


Produktspezifikationen

Marke: Tactical Fiber Systems
Kategorie: Nicht kategorisiert
Modell: CCRT241

Brauchst du Hilfe?

Wenn Sie Hilfe mit Tactical Fiber Systems CCRT241 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Tactical Fiber Systems

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-