TacTic TACJ2005 Bedienungsanleitung

TacTic Funkgesteuertes Spielzeug TACJ2005

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für TacTic TACJ2005 (4 Seiten) in der Kategorie Funkgesteuertes Spielzeug. Dieser Bedienungsanleitung war für 9 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/4

The AnyLink2 SLT 2.4GHz

Radio Adapter can greatly

expand a transmitter’s

versatility, allowing it to be

used with a huge variety

of ﬂ ight models, including

Tx-R

™

Transmitter-Ready

™

aircraft (including Select Scale and Micro Tx-R models). AnyLink2 is

capable of full range, to control any size aircraft.

Read this manual in its entirety before use! Damage resulting

from misuse or modiﬁ cation will void your warranty.

ITEMS INCLUDED

(1) AnyLink2 2.4GHz Radio Adapter with 1S LiPo Battery

(1) Cable A – JR®, Spektrum®, Graupner®

(1) Cable B – Futaba® Square

(1) Cable C – Spektrum, Hitec®

(1) TC10 USB Charger

(2) Hard Locking Adhesive Strips

(1) Instruction sheet

COMPATIBLE TRANSMITTERS

AND RECEIVERS

AnyLink2 can link virtually any brand transmitter (Tx) to any Tactic brand

2.4GHz receiver (Rx) such as the TR624 or TR625. Transmitters must be

equipped with a functioning trainer jack, and can originally be designed

for use on 72MHz, 2.4GHz, FM, PCM, etc. Go to www.tacticrc.com for a

comprehensive Tx compatibility chart. AnyLink2 is not compatible with

non-Tactic brand receivers not having SLT technology.

TX CABLE

See the chart below to determine the cable needed to connect AnyLink2 to

the Tx. Three cables are included, for many Futaba, Hitec, JR, Spektrum,

and Graupner brand radios.

This chart is current as of the date of the printing of this manual. Check

www.tacticrc.com for the most updated compatibility chart. Transmitters

not listed may or may not be compatible with AnyLink2. See your local

hobby retailer for optional cables for other radio types:

TACM0013 AnyLink2 Cable Futaba/Hitec Round

TACM0014 AnyLink2 Cable Airtronics SD-Series

TACM0015 AnyLink2 Cable Airtronics 5-Pin Round

IMPORTANT: For some transmitters, connecting a cable to the

trainer jack will automatically cause the Tx logic circuitry to turn

on. When not in use, make sure to disconnect the cable from trainer jack

to prevent the Tx battery from discharging completely.

ANYLINK2

AnyLink2 Transmitter Compatibility Chart

ANYLINK2

MODE

BRAND MODEL CABLE

Futaba®

4YF (72M, 2.4G), 4YBF, 6EX, TJ, 7C, 8FG, 8J, 9C, 10C, 14SG; (12FG, 12Z, 14MZ, 18MZ

> )See note page 2 *

4VF, 5U, 6A, 6DA, 6H, 6X, 6YF, 6YG, 7U, 7NFK, 8U, 9Z

Hitec ®

Optic 5, Optic 6 Sport, and Eclipse 7 (all on 2.4GHz), Aurora 9

Neon, Flash 4sx, Flash 5, Flash 5sx, Focus 4, Focus 6, Laser 4, Laser 6, Optic 5 (72M),

Optic 6 (72M, 2.4G), Eclipse 7 (72M), Prism 7, Prism 7X

Tower Hobbies

4FM, 6FM

4TH, 6XM

Graupner ®

MX-12, MX-16

Walkera ®

Devo 7, Devo 8S

Airtronics ®

SD-5G, SD-6G, SD-10G

Vanguard 4FM, 6FM, RD6000 Sport, RD6000 Super, RDS8000, Radiant 6FM

Spektrum

DX4e, DX5e, DX6, DX7, DX7s, DX8, DX9, DX10T, DX18

DX6i

JR ®

All with trainer/DSC jack

(Included)

(TACM0013)

(TACM0014)

(TACM0015)

BATTERY AND CHARGER

AnyLink2 is powered by an included 1S 3.7V 450mAh lithium-polymer

battery (LiPo).

IMPORTANT:

It will be necessary to fully charge the battery with

the included USB charger before use! Follow all safety precautions

below before proceeding. Failure to do so may cause AnyLink2 to lose

power prematurely, resulting in a loss of control signal and causing the

model to crash.

●

NEVER LEAVE BATTERY UNATTENDED WHILE CHARGING

● Never allow the battery temperature to exceed 140°F (60°F)

● Never place battery on combustible materials while charging

● Never attempt to disassemble or modify the battery

● Never attempt to charge or continue to use the battery if it’s swollen,

punctured, or deformed in any way.

● Never attempt to charge the battery with an incompatible battery

charger. Only use the included charger.

● Follow appropriate disposal instructions when the battery has reached

the end of its useful life

Open the battery door on the rear side of AnyLink2 and remove the battery.

2. Connect the included TC10 USB charger to a personal computer’s USB

port, and turn the computer on.

3. Connect the LiPo battery to the jack on the opposite end of the charger.

4. The charger’s red LED will turn on to conﬁ rm charge is being delivered.

When the charger automatically detects full charge is achieved, the red

LED will ﬂ ash slowly. The battery can be removed at this time and is ready

for use. Note: Rapid ﬂ ashing of the LED indicates an error occurred.

The battery should be disconnected from the charger and placed in a

ﬁ reproof location. Contact Hobby Services

6. If the battery was successfully charged, attach it to the connector inside

AnyLink2. Carefully insert the battery inside AnyLink2 and close the

door, making sure not to pinch the wires in the door.

AnyLink2 turns on automatically when connected to a host transmitter

and a signal is present at the trainer jack. Otherwise, AnyLink2’s power

will remain off.

Tones will sound from AnyLink2 if its battery voltage drops to an unsafe

level (3.25V). Land the aircraft immediately to avoid loss of control

and possible destruction of the model. Fully re-charge the battery before

further use.

ANYLINK2 MODE SETUP

IMPORTANT!

Remove the airplane’s propeller prior to setting up

AnyLink2 to work with the ﬂ ight system. Failure to do so could result

in personal injury if the motor turns unexpectedly. Make sure all

batteries are fully charged prior to operation. Make sure all connections are

solid physically and cannot easily become dislodged at any time. AnyLink2

must be used with a Tx having a throttle stick that does NOT automatically

spring back to center.

1. Create a new model memory in the host transmitter before starting to

conﬁ gure AnyLink2.

2. Mount AnyLink2 to the host Tx, by either clipping the mounting grip

onto the handle of the host Tx, or using the two hard locking mounting

strips included. Extend AnyLink2’s antenna upwards from the top of the

Tx as much as possible.

3. Remove the Rf module or crystal from the host Tx if possible, or disable

its Rf function.

4. Leave the transmitter’s own antenna in a retracted or folded position.

For computer radios make sure the modulation is set to PPM mode. For

transmitters having the option to transmit a signal when Tx power is

turned ON, make sure “YES” is selected. Futaba 12FG, 12Z, 14MZ, and *

18MZ transmitters must be mapped for Futaba channel order before use.

6. Move the throttle stick to minimum; leave all other sticks at center.

Connect the appropriate cable to the Tx trainer jack. If the transmitter’s

logic turns on automatically do NOT turn the Tx’s power switch on as it

could cause AnyLink2 to not function. Otherwise, if the transmitter’s logic

circuitry does NOT turn on automatically, turn the Tx power switch ON.

8. AnyLink2 should beep when a signal is received from the Tx and a red

LED should illuminate at this time. Identify the letter printed next to the

illuminated LED from the following list:

F Futaba

J JR (also works for Graupner)

S Spektrum

H Hitec

A Airtronics (also works for Walkera)

C Custom

If the LED illuminates next to the proper letter for the connected radio,

skip to the next section.

If the proper LED is not illuminated, insert a small screwdriver into the hole

next to “MODE” and press the button repeatedly until the LED illuminates

next to the proper Tx brand letter. The LED will ﬂ ash. Disconnect the cable

from AnyLink2, and re-connect. The LED should now stay on constantly

next to this selected radio setting. AnyLink2 should now be conﬁ gured for

the Tx and will retain this setting even after power is removed. Resetting

AnyLink2’s radio setting will only be necessary when a different brand Tx

will be connected.

CUSTOM MODE SETUP

If using a radio brand not listed above, AnyLink2 can be custom conﬁ gured

for your radio.

1. Create a new model memory in the host transmitter before starting to

conﬁ gure AnyLink2.

2. Move the Tx throttle stick and throttle trim to minimum position. Leave

all other sticks and trims at center position.

3. Connect the proper cable to the host transmitter’s trainer jack. If the

transmitter’s logic doesn’t turn on automatically, turn the Tx power

switch ON.

4. Connect the cable to AnyLink2, which should power up automatically if

a trainer signal is present.

5. Press AnyLink2’s MODE button and hold until the LED next to “C”

begins to ﬂ ash.

6. Move the throttle trim to center position, then move the throttle stick

to center position. A tone should sound to indicate the throttle channel

is at center.

7. Determine which stick will be used for aileron control. Move that stick to

the far-right position, then to the far-left position, then return to center.

8. Determine which stick will be used for elevator control. Move that stick

to the far-up position, then to the far-down position, then return to

center.

9. Determine which stick will be used for throttle control. Move that stick

to the far-up position, then far-down position, then return to center.

10 . Determine which stick will be used for rudder control. Move that stick

to the far-right position, then far-left position, then return to center.

11 .

Move the throttle stick to minimum position, which should be followed by

a beep and the LED should illuminate next to “C” to indicate Custom mode

is set. AnyLink2 will save this custom data and exit this setting mode.

12 . Remove power from AnyLink2, and then re-apply. AnyLink2 should be

conﬁ gured to work with this Tx. Once power is removed from AnyLink2

it will not be necessary to reset Custom mode.

LINKING TO A TACTIC RX

To use AnyLink2 with a Micro Tx-R airplane skip to the next section.

Otherwise, to link to a Tactic brand Rx or Select Scale Tx-R aircraft, refer

to the instructions included with the receiver, or go to www.tacticrc.com/

receivers/index.html to ﬁ nd an instruction sheet as needed.

Remember to set the failsafe on the Tactic receiver.

NOTE: Tactic receiver TR1424 does not include a failsafe function. Tactic

receiver TR424 includes a non-adjustable failsafe where the throttle

position is automatically established based on the maximum or minimum

position of the throttle stick (CH3) each time the TR424 is linked to a Tx.

All other channels will hold their last position.

For all other Tactic receivers, the factory default is that CH3 deﬂ ects to

0% (minimum) which should stop motor function if the Rx loses signal,

and all other channels will hold their last position. The throttle deﬂ ection

position can be changed manually if desired. IMPORTANT! Conﬁ rm the Tx

servo reversing settings are in the correct position for the application. To

manually set the throttle failsafe:

A. Make sure the model’s ESC is NOT armed. If using a combustion engine

make sure it’s NOT running.

B. Move the Tx throttle stick to the desired failsafe position.

C. Press and hold the Rx “LINK” button until the Rx LED blinks twice.

D. Release the LINK button. The Rx LED should stay illuminated to indicate

the Rx is now linked, with the throttle failsafe in the new position as set

above.

E. Skip to the SYSTEM CHECK AND OPERATION section.

AUTO-LINKING ANYLINK2 TO

MICRO TX-R AIRCRAFT

When power is originally applied to a Micro Tx-R aircraft the built-in Rx

will automatically search for the strongest signal being emitted from

any Tactic 2.4GHz Tx (including TTX402, 403, AnyLink2, etc.), or other

brand Tx which is currently emitting the SLT protocol, and link to that

signal. There are no link buttons to press to establish this link. A link is

established when the red LED on the board illuminates.

Later, if power is re-applied to the same Micro Tx-R aircraft while multiple

Tactic transmitters are operating simultaneously – including the original

transmitter “A” – the Micro Tx-R aircraft will attempt to re-link with

transmitter “A”. However, if power is re-applied to the Micro Tx-R aircraft

while a signal is being emitted from a different Tactic transmitter, the

Micro Tx-R aircraft will now automatically link to the new transmitter (Tx

“B”). To re-establish the link with Tx “A”, repeat this process but apply

power only to Tx “A” before applying power to the Micro Tx-R aircraft.

Try these tips if the Micro Tx-R aircraft has difﬁ culty linking with AnyLink2

when multiple Tactic signals are present:

1. Pre-link your AnyLink2 and Micro Tx-R aircraft before arriving at the

ﬂ ying site.

Turn on the Tx/AnyLink2 before applying power to the Micro Tx-R aircraft.

3. Wait for other pilots ﬂ ying Tactic to remove power from their Tx/

AnyLink2 before attempting to link.

4. Move further away from other Tactic transmitters before powering your

equipment.

SYSTEM CHECK AND OPERATION

Check the general operation of the system and all ﬂ ight equipment before

attempting a ﬂ ight.

WARNING! With the aircraft on the ground, make sure the throttle

stick remains at the minimum position and is not accidentally

moved. NOTE: Micro Tx-R aircraft have a throttle arming procedure

which does require movement of the throttle channel during setup (see

instructions included with the Micro Tx-R aircraft).

Range Check: Determine the safe operating distance from the Tx to the Rx.

Place the aircraft on the ground and walk 100 feet (30m) away from the

model. Conﬁ rm that smooth, interference-free control of all surfaces exists.

Failsafe Check: If using the failsafe feature, test for proper operation:

1. Prepare a way to quickly disconnect the battery/ESC connection if

power needs to be cut immediately.

2. Have an assistant hold the aircraft in place on a test stand, with hands

away from the motor.

3. Apply power to the system and test the motor and ﬂ ight gear for general

operation.

4. Remove power from the Tx/AnyLink2.

5. Observe the model’s surfaces to ensure they move to the previously set

failsafe positions.

6. If failsafe operation is correct, re-connect power to the system as

explained earlier and prepare for ﬂ ight. If the failsafe function does not

operate correctly, re-check the LINKING TO A TACTIC Rx and SYSTEM

CHECK AND OPERATION sections and re-try.

7. After the ﬂ ight is complete, remove power from the ﬂ ight system as

soon as possible, then the transmitter and AnyLink2.

INACTIVITY ALARM AND

REMOVING POWER

If no Tx controls are moved for 5 minutes, AnyLink2 will ﬂ ash all LEDs

simultaneously and tones will sound to alert that power is still ON and

AnyLink2 is still transmitting a signal. After power has safely been removed

from the model, power must be removed from AnyLink2 by disconnecting it

from the transmitter’s trainer jack or turning off power to the Tx (depending

on Tx type).

SPECIFICATIONS

Compatible Rxs: Tactic 2.4GHz, Tx-R aircraft, Rxs having SLT protocol

Frequencies: 2.403 – 2.479GHz

Modulation: FHSS spread spectrum

Flight range: full range

Input power: 3.30 – 4.20V, 150mA

Power control: automatic with incoming signal recognition

Power on indicator: red LEDs with audible tones

Low voltage alarm: audible tones at 3.25V

Inactivity alarm: tones sound after 5 minutes of Tx inactivity

Output power: < 0.1W

Case dimensions: 2.68 x 1.46 x 0.98" (68 x 37 x 25mm)

Weight: 1.62 oz. (46g)

TACTIC ACCESSORIES

See your local hobby retailer for any of these optional parts:

TACL0624 TR624 2.4GHZ 6CH Receiver

TACL0625 TR625 2.4GHZ 6CH Twin Antenna Receiver

TACP0010 AnyLink2 TC10 USB 1S LiPo Charger

TACP0011 AnyLink2 1S 3.7V 450mAh 25C LiPo Battery

IMPORTANT WARNING AND

PRECAUTIONS

● Do not allow water or moisture inside AnyLink2.

● Do not operate R/C model aircraft near power lines, radio or cell

phone towers, roads or automobiles, buildings, or pedestrians.

● Do not operate R/C equipment if you are physically impaired as it could

pose a safety hazard to yourself or others in the area.

● Do not allow small children to operate/control model R/C equipment

without the supervision of an adult.

● Do not allow the transmitter’s throttle stick to accidentally be moved

away from the “off” or minimum position while the model’s engine/

motor is running.

● Do not allow chemicals to come in contact with any parts of AnyLink2.

Substances such as glow fuel, gasoline, CA glue, etc. could permanently

damage the case and electronic components.

● Always follow the Academy of Model Aeronautics National Model

Aircraft Safety Code when operating an R/C aircraft.

Produktspezifikationen

Marke:	TacTic
Kategorie:	Funkgesteuertes Spielzeug
Modell:	TACJ2005

Brauchst du Hilfe?

Wenn Sie Hilfe mit TacTic TACJ2005 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Funkgesteuertes Spielzeug TacTic

TacTic TR325 Bedienungsanleitung

13 September 2024

TacTic AnyLink2 Bedienungsanleitung

2 September 2024

TacTic TACJ2005 Bedienungsanleitung

27 Juli 2024

TacTic TTX410 Bedienungsanleitung

4 Juli 2024

Bedienungsanleitung Funkgesteuertes Spielzeug

Neueste Bedienungsanleitung für -Kategorien-

Proline Trencher Bedienungsanleitung

4 Oktober 2024

Futaba 12Z Bedienungsanleitung

4 Oktober 2024

Graupner 33718.XT60 Bedienungsanleitung

3 Oktober 2024

Amewi Hyper Go Bedienungsanleitung

1 Oktober 2024

Carson Drift Burner Bedienungsanleitung

1 Oktober 2024

Carson Micro X-Warrior 2.0 Bedienungsanleitung

1 Oktober 2024

Biltema 45-8119 Bedienungsanleitung

1 Oktober 2024

Traxxas Stampede Bedienungsanleitung

29 September 2024

Hobbywing XeRun XR10 Pro WP Bedienungsanleitung

25 September 2024

Hobbywing XeRun XR10 Stock Spec G2 Bedienungsanleitung

25 September 2024