Swann SWIFI-COREPRO3S3 Bedienungsanleitung

Swann Nicht kategorisiert SWIFI-COREPRO3S3

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Swann SWIFI-COREPRO3S3 (40 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 3 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/40
CoreCam Pro 2K Wire-Free Security Camera
with Spotlight
Cámara de seguridad CoreCam Pro 2K con Foco
Caméra de sécuritéde CoreCam Pro 2K avec Projecteur
Telecamera di sicurezza CoreCam Pro 2K con illuminazione
CoreCam Pro 2K Ãœberwachungskamera mit Spotlight
EN Quick Start Guide ES Guía de inicio rápido FR Guide de démarrage rapide
IT Guida rapida DE Schnellstartanleitung
Model: SWIFI-COREPRO
2
EN
CAMERA OVERVIEW
Threaded screw hole
(to attach included wall-mount bracket)
Pull rubber cap gently from the bottom to access:
• ON/OFF switch
• MicroSD card slot
32GB card pre-installed, Max. 128GB card supported
• Micro USB charging port
• Reset button
— Press and hold for 5 seconds to enter pairing mode
— Press and hold for 10 seconds to factory reset the camera
Microphone Speaker
QR code (for
device pairing)
Rubber cap
Passive infrared
motion sensor
LED indicator
Night detection
sensor
Infrared LEDs
(for night vision) Spotlight
Threaded
mounting post
Bracket screw hole (x3)
Locking knob
3
EN
GETTING STARTED
Before using the camera for the first time, fully charge it with the included micro USB charging cable.
1 Pull open the rubber cap on the bottom of the camera.
2 Slide the switch to the position ON/OFF ON Note: You can also charge the camera with the
switch OFF but you won’t be able to check the LED indicator for the charging status.
3 Insert the smaller end of the micro USB charging cable into the micro USB port on the camera.
4 Insert the other end of the micro USB charging cable into a USB wall charger such as the USB
power adapter for your smartphone.
5 The LED indicator on the front of the camera will turn solid blue indicating that the camera is
charging. When the camera is fully charged, the LED indicator will turn off. Actual charging times
may vary depending on the USB power supply (DC5V 2A is recommended for faster charging) and
the remaining battery level. A full charge may take up to 6 hours.
6 After charging is finished, unplug the micro USB charging cable from the camera and make sure
to close the rubber cap tightly to keep out water and dust.
The camera comes with a 32GB microSD card pre-installed for recording events and performing
firmware updates. You can easily replace the microSD card with a new one (max. 128GB card
supported), if needed in the future. Simply open the rubber cap on the bottom of the camera, eject
the current microSD card (push in until it clicks) from the microSD card slot, and then insert the new
microSD card (with the label side facing the front of the camera) into the slot until it clicks into place.
You should format the microSD card the first time it is used. From the Swann Security app, go to
Device Settings > [your camera] > and tap Advanced Settings Format.
Charging the camera
Replacing the microSD card


Produktspezifikationen

Marke: Swann
Kategorie: Nicht kategorisiert
Modell: SWIFI-COREPRO3S3

Brauchst du Hilfe?

Wenn Sie Hilfe mit Swann SWIFI-COREPRO3S3 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Swann

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-